BS ISO 9255-2008 Aerospace - Bolts normal spline head normal shank short or medium length MJ threads metallic material coated or uncoated strength classes less than or equal to 110.pdf

1、BS ISO 9255:2008ICS 49.030.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace Bolts,normal spline head,normal shank, shortor medium lengthMJ threads, metallicmaterial, coated oruncoated, strengthclasses less than orequal to 1 100 MPa DimensionsThis Brit

2、ish Standardwas published underthe authority of theStandards Policy andStrategy Committee on 30September 2008 BSI 2008ISBN 978 0 580 55030 0Amendments/corrigenda issued since publicationDate CommentsBS ISO 9255:2008National forewordThis British Standard is the UK implementation of ISO 9255:2008. Its

3、upersedes BS A 308:1994 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport

4、to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 9255:2008Reference numberISO 9255:2008(E)ISO 2008INTERNATIONAL STANDARD ISO9255Second edition2008-08-15Aerosp

5、ace Bolts, normal spline head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions Aronautique et espace Vis tte cannele normale, avec tige normale et filetages MJ courts ou de longueur moyenne, en matria

6、u mtallique, revtues ou non revtues, des classes de rsistance infrieures ou gales 1 100 MPa Dimensions BS ISO 9255:2008ISO 9255:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited

7、unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trade

8、mark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies

9、. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any mea

10、ns, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyr

11、ightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedBS ISO 9255:2008ISO 9255:2008(E) ISO 2008 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work

12、of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-government

13、al, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The mai

14、n task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Att

15、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 9255 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 4,

16、Aerospace fastener systems. This second edition cancels and replaces the first edition (ISO 9255:1993), which has been technically revised. BS ISO 9255:2008BS ISO 9255:2008INTERNATIONAL STANDARD ISO 9255:2008(E) ISO 2008 All rights reserved 1Aerospace Bolts, normal spline head, normal shank, short o

17、r medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa Dimensions 1 Scope This International Standard specifies the dimensions of normal spline head bolts, with close or large tolerance normal shank and short or medium length MJ threads, i

18、n metallic material, coated or uncoated, with strength classes less than or equal to 1 100 MPa. This International Standard is applicable to the compilation of aerospace product standards. 2 Normative references The following referenced documents are indispensable for the application of this documen

19、t. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 3353-1

20、, Aerospace Lead and runout threads Part 1: Rolled external threads ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts ISO 7403, Aerospace Spline drives Wrenching configuration Metric series ISO 7913, Aerospace Bolts and screws, metric Tolerances of form and position 3 Conf

21、iguration and dimensions See Figure 1 and Table 1. Dimensions and tolerances are expressed in millimetres. They are applicable after any coating (tolerance on shank diameter before coating is also specified for heat cured matrix coatings), but before the application of any lubricant. Details of form

22、 not stated are left to the manufacturers discretion. Tolerances of form and position shall be as specified in ISO 7913 if not otherwise stated on product standard. BS ISO 9255:2008ISO 9255:2008(E) 2 ISO 2008 All rights reservedDimensions in millimetres Break sharp edges 0,1 to 0,4 Key 1 thread aRou

23、nded or chamfered in this area. bShape optional. cIn accordance with ISO 3353-1. Figure 1 BS ISO 9255:2008ISO 9255:2008(E) ISO 2008 All rights reserved 3Blank page BS ISO 9255:2008ISO 9255:2008(E) 4 ISO 2008 All rights reservedTable 1 D1Coated bolts Uncoated bolts Tol. Tol. D2D3D4D5D6D7 Four holes,

24、equi-distant, optional D8 One hole, optionalDiameter code Threadanom. before coatingbclose large close large,050+nom. Tol. min. min. max. H13cH13c040 MJ4 0,7-4h6h 4 3 ,0056 7,5 8,3 1,1 050 MJ5 0,8-4h6h 5 3,2 3,4 7 8, 9,1 1 060 MJ6 1-4h6h 6 0,0300,045 0,010 0,035 4,1 4,2 8 9,8 10,6 1,5 070 MJ7 1-4h6h

25、 7 4,9 5, 9 11,3 12,1 080 MJ8 1-4h6h 8 5,2 6, 10 12,8 13,6 1,4 1,9 100 MJ10 1,25-4h6h 10 0,0330,048 0,013 0,038 6,7 7,9 12 15,7 16,7 120 MJ12 1,25-4h6h 12 0,0360,051 0,016 0,041 h12cf7ch12c8 9,8 0,514 18,8 19,9 1,6 2,4 BS ISO 9255:2008ISO 9255:2008(E) ISO 2008 All rights reserved 5Table 1 (continued

26、) L2L3 H K L1 0,2 dThread Thread P R S T min. h15 cshort medium short medium nom. Tol. ,040+min. Wrenching dash numbere0,8 5,5 2 to 40 7,5 10 5 6 3,5 0,4 2,5 060 1 6,5 3 to 50 9 12 6 7,5 4,5 0,5 2,5 2,8 070 1,2 7,5 3 to 60 10 14 8,5 5,2 2,8 3,5 080 1,4 8,2 4 to 70 11 15 7 9,5 5,9 3,3 3,8 090 1,6 8,6

27、 4 to 80 11,5 16,5 7,5 10,5 6,3 0,7 3,7 3,9 100 2 10,1 5 to 100 14,5 20,5 9 13 7,7 0,8 ,0024,7 4,2 120 2,4 11,4 6 to 120 16 22,5 10 14,5 8,8 0,9 ,0035,6 4,5 140 aIn conformity with ISO 5855-2, except for the maximum thread major diameter, dmax, of bolts with a close tolerance on D1, which shall be e

28、qual to (D1,min 0,025). bHeat cured organic matrix coatings for close tolerance normal shanks. cSee ISO 286-2. dIncrements: 1 for L1u 30; 2 for 30 100. If greater lengths are required, they shall be chosen using these increments. eIn conformity with ISO 7403 over T min. BS ISO 9255:2008ISO 9255:2008

29、(E) ICS 49.030.20 Price based on 4 pages ISO 2008 All rights reserved BS ISO 9255:2008This page has been intentionally left blank BS ISO9255:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independ

30、ent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they posses

31、s the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of wh

32、ich can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and forei

33、gn standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI im

34、plementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic info

35、rmation services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase pric

36、e of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI

37、website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval syste

38、m or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: