BS ISO 96-2-2009 Textile machinery and accessories - Rings and travellers for ring spinning and ring twisting frames - HZ- and J-rings and their travellers《纺织机械和附件 环锭细纱机和环锭捻线机用钢领和钢.pdf

1、BS ISO 96-2:2009ICS 59.120.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTextile machinery andaccessories Ringsand travellers for ringspinning and ringtwisting framesPart 2: HZ- and J-rings and theirtravellersThis British Standardwas published underthe autho

2、rity of theStandards Policy andStrategy Committee on 30September 2009 BSI 2009ISBN 978 0 580 56362 1Amendments/corrigenda issued since publicationDate CommentsBS ISO 96-2:2009National forewordThis British Standard is the UK implementation of ISO 96-2:2009. Itsupersedes BS ISO 96-2:1992 which is with

3、drawn.The UK participation in its preparation was entrusted to TechnicalCommittee TCI/33, Textile machinery.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users a

4、re responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 96-2:2009Reference numberISO 96-2:2009(E)ISO 2009INTERNATIONAL STANDARD ISO96-2Second edition2009-03-01Textile machinery and accessories Rings and travellers for ring spi

5、nning and ring twisting frames Part 2: HZ- and J-rings and their travellers Matriel pour lindustrie textile Anneaux et curseurs pour machines filer et retordre Partie 2: Anneaux HZ et J et leurs curseurs BS ISO 96-2:2009ISO 96-2:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In

6、 accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Ado

7、bes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for

8、 printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless oth

9、erwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyrig

10、ht office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 96-2:2009ISO 96-2:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the International Organization for S

11、tandardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the ri

12、ght to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Internationa

13、l Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as

14、an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO

15、 96-2 was prepared by Technical Committee ISO/TC 72, Textiles machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories. This second edition cancels and replaces the first edition (ISO 96-2:1992), which has been technically revised.

16、ISO 96 consists of the following parts, under the general title Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames: Part 1: Flange rings T and SF and their travellers Part 2: HZ- and J-rings and their travellers BS ISO 96-2:2009BS ISO 96-2:2009INTERNATI

17、ONAL STANDARD ISO 96-2:2009(E) ISO 2009 All rights reserved 1Textile machinery and accessories Rings and travellers for ring spinning and ring twisting frames Part 2: HZ- and J-rings and their travellers 1 Scope This part of ISO 96 specifies the principal dimensions of HZ- and J-rings, and the mass

18、and tolerance on the mass, of the appropriate travellers for HZ- and J-rings employed on ring spinning and ring twisting machines. It also specifies the method of designation of the travellers. 2 Normative references The following referenced documents are indispensable for the application of this do

19、cument. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 3, Preferred numbers Series of preferred numbers 3 Principal dimensions of HZ- and J-rings The principal dimensions of HZ- and J

20、-rings are illustrated in Figure 1 and Figure 2, respectively, and specified in Table 1. Figure 1 Example of an HZ-ring (vertical ring) BS ISO 96-2:2009ISO 96-2:2009(E) 2 ISO 2009 All rights reservedFigure 2 Example of a J-ring (conical ring) Table 1 Ring dimensions Dimensions in millimetres Ring ty

21、pe HZ J inside diameter Tolerance of fitting diameter d1height height d tolerance ah h 0,10+0,10+45 48 50 6,3 55 60 9,5 65 70 10,3 75 80 00,2511,1 9,1 90 100 16,7 110 125 00,3225,4 11,1 140 150 160 00,438,1 17,4 180 200 200 00,55aThe tolerance refers to the diameter d1, excluding any ovality. BS ISO

22、 96-2:2009ISO 96-2:2009(E) ISO 2009 All rights reserved 34 Travellers 4.1 Examples of travellers appropriate for HZ- and J-rings are shown in Figures 3 and 4, and Figures 5 and 6, respectively. Figure 3 Example of a metal traveller on an HZ-ring Figure 4 Example of a plastic traveller on an HZ-ring

23、Figure 5 Example of a metal traveller on a J-ring Figure 6 Example of a plastic traveller on a J-ring BS ISO 96-2:2009ISO 96-2:2009(E) 4 ISO 2009 All rights reserved4.2 The values for traveller mass are given in Table 2. The traveller mass is taken from the R20 series of preferred numbers in accorda

24、nce with ISO 3. The range of traveller mass comprises values from 9 to 20 000 inclusive. The traveller mass represents the nominal mass, in grams, of 1 000 travellers of the same type. The tolerance on the nominal mass for 1 000 travellers of the same type is 3 % for metal travellers and ()50%+for p

25、lastic travellers. Table 2 Traveller mass Mass of traveller (grams per 1 000 travellers) 9 63 450 3 150 10 71 500 3 550 11,2 80 560 4 000 12,5 90 630 4 500 14 100 710 5 000 16 112 800 5 600 18 125 900 6 300 20 140 1 000 7 100 22,4 160 1 120 8 000 25 180 1 250 9 000 28 200 1 400 10 000 31,5 224 1 600

26、 11 200 35,5 250 1 800 12 500 40 280 2 000 14 000 45 315 2 240 16 000 50 355 2 500 18 000 56 400 2 800 20 000 BS ISO 96-2:2009ISO 96-2:2009(E) ISO 2009 All rights reserved 55 Designation of travellers The designation of a traveller for an HZ- or J-ring shall include the following information: a) “Tr

27、aveller”; b) reference to this part of ISO 96 (i.e. ISO 96-2); c) the symbol “HZ” or “J”; d) the height, h, in millimetres, of the appropriate ring; e) the manufacturers designation for the traveller style (optional); f) the wire section symbol (if applicable), e.g. “f ”, “r ” (“f ” = flat, “r” = ro

28、und); g) the traveller mass (see Table 2); h) the traveller material if it is other than steel (where this information is omitted, it is assumed that the traveller material is steel); i) the surface finish (optional); j) the presentation (loose or stacked). BS ISO 96-2:2009ISO 96-2:2009(E) ICS 59.12

29、0.10 Price based on 5 pages ISO 2009 All rights reserved BS ISO 96-2:2009This page has been intentionally left blank BS ISO96-2:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national

30、body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest

31、amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be fo

32、und on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards

33、publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation

34、of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information servi

35、ces are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standard

36、s. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at ht

37、tp:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmit

38、ted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: