BS ISO IEC 11160-2-2013 Information technology Office equipment Minimum information to be included in specification sheets Printers Class 3 and Class 4 printers《信息技术 办公设备 规格单中含有的最少.pdf

1、BSI Standards PublicationBS ISO/IEC 11160-2:2013Information technology Office equipment Minimuminformation to be included inspecification sheets PrintersPart 2: Class 3 and Class 4 printersBS ISO/IEC 11160-2:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO/

2、IEC11160-2:2013.The UK participation in its preparation was entrusted to TechnicalCommittee IST/3, IT Printers and Cartridges.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a

3、 contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 78295 4ICS 35.180Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the aut

4、hority of theStandards Policy and Strategy Committee on 31 October 2013.Amendments issued since publicationDate Text affectedBS ISO/IEC 11160-2:2013Reference numberISO/IEC 11160-2:2013(E)ISO/IEC 2013INTERNATIONAL STANDARD ISO/IEC11160-2Second edition2013-10-15Information technology Office equipment

5、Minimum information to be included in specification sheets Printers Part 2: Class 3 and Class 4 printers Technologies de linformation quipements de bureau Information minimale devant figurer dans les notices techniques Imprimantes Partie 2: Imprimantes classe 3 et classe 4 BS ISO/IEC 11160-2:2013ISO

6、/IEC 11160-2:2013(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2013 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet

7、, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Publis

8、hed in Switzerland ii ISO/IEC 2013 All rights reservedBS ISO/IEC 11160-2:2013ISO/IEC 11160-2:2013(E) ISO/IEC 2013 All rights reserved iiiContents Page Foreword iv Introduction . v 1 Scope 1 2 Conformance . 1 3 Normative references 1 4 Test and measurement conditions 2 5 Information to be included in

9、 the specification sheets . 2 Annex A (normative) Classification of printers -Class 3 and Class 4 . 9 Annex B (informative) Test Pattern . 11 Annex C (informative) Classification of Printers . 13 Annex D (informative) Example of a layout for a specification sheet . 14 Bibliography 17 BS ISO/IEC 1116

10、0-2:2013ISO/IEC 11160-2:2013(E) iv ISO/IEC 2013 All rights reservedForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC parti

11、cipate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmenta

12、l and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

13、The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodie

14、s casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/IEC 11160-2 was prepared by Joint Technical Committee ISO/IEC JTC 1, Informatio

15、n technology, Subcommittee SC 28, Office equipment. This second edition cancels and replaces the first edition which has been technically revised. ISO/IEC 11160 consists of the following parts, under the general title Information technology Office equipment Minimum information to be included in spec

16、ification sheets Printers: Part 1: Class 1 and Class 2 printers Part 2: Class 3 and Class 4 printers Annex A forms an integral part of this part of ISO/IEC 11160. Annexes B, C and D are for information only. BS ISO/IEC 11160-2:2013ISO/IEC 11160-2:2013(E) ISO/IEC 2013 All rights reserved vIntroductio

17、n Printers of many different types and capacities are now available and their specifications vary so widely that it is difficult for potential users to assess which machine might best meet their requirements. BS ISO/IEC 11160-2:2013BS ISO/IEC 11160-2:2013INTERNATIONAL STANDARD ISO/IEC 11160-2:2013(E

18、) ISO/IEC 2013 All rights reserved 1Information technology Office equipment Minimum information to be included in specification sheets Printers Part 2: Class 3 and Class 4 printers 1 Scope ISO/IEC 11160 is intended to facilitate users in selecting a printer which meets their requirements. ISO/IEC 11

19、160 specifies the minimum information to be included in the specification sheets of printers in order for users to compare the characteristics of different machines. The term “Specification Sheets” applies to documents which describe the performance characteristics of the printers to be included in

20、instruction manuals, product brochures or on websites. ISO/IEC 11160 applies to printers that could be operated in an office environment. Printers requiring specially equipped rooms or specially instructed operators are not considered in ISO/IEC 11160. ISO/IEC 11160 deals with different classes of p

21、rinters This part of ISO/IEC 11160 accommodates Class 3 and Class 4 printers, as defined in Annex C. Detailed descriptions of Class 3 and Class 4 printers are specified in Annex A. Serial printers are classified as Class 1 or Class 2 printers as defined in Annex C and covered by Part-1 of ISO/IEC 11

22、160. 2 Conformance In order to comply with this part of ISO/IEC 11160, specification sheets shall include, in the order shown, all required items listed in clause 5 which are relevant to the machine being described. 3 Normative references The following documents, in whole or in part, are normatively

23、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7779, Acoustics Measurement of airborne noise emitted by informa

24、tion technology and telecommunications equipment ISO 9295, Acoustics Measurement of high-frequency noise emitted by computer and business equipment ISO 9296, Acoustics Declared noise emission values of computer and business equipment ISO/IEC 19752, Information technology Method for the determination

25、 of toner cartridge yield for monochromatic electrophotographic printers and multi-function devices that contain printer components ISO/IEC 19798, Information technology Method for the determination of toner cartridge yield for colour printers and multi-function devices that contain printer componen

26、ts BS ISO/IEC 11160-2:2013ISO/IEC 11160-2:2013(E) 2 ISO/IEC 2013 All rights reservedISO/IEC 24711, Method for the determination of ink cartridge yield for colour inkjet printers and multi-function devices that contain printer components ISO/IEC 24734, Information technology Office equipment - Method

27、 for measuring digital printing productivity 4 Test and measurement conditions Unless otherwise specified, all tests and measurements shall be conducted at the following conditions: a) Temperature: 23 C 5C b) Relative humidity: 50 % 20 % c) Line Voltage: rated input voltage d) Line Frequency: rated

28、frequency e) Paper size: A4 f) Paper weight: 60 g/m2 to 90 g/m2g) Paper transport direction: standard direction For the test pattern, the document in Annex B (Informative) should be used. Annex B is derived from ISO/IEC 10561, where the guide line (character art, size etc) is given for the creation

29、of the test target. So long as the document is text only, a bit of modification causes no influence over the results of measurement. For monochrome test pattern, all letters should be black. For colour test pattern, arbitrary letters should be colourized by using the primary colorants of the printer

30、. Instead of A4 paper size, the size most commonly used in the country may be used, both for the test page and the copies. This shall be indicated in the specification sheet. 5 Information to be included in the specification sheets Table 1 defines, for each parameter, the name of the parameter and a

31、 short description of the entry. These constitute the information to be included in the specification sheet. Parameters whose properties shall be included in the specification sheets are marked as “R“ (required), while other parameters whose properties are recommended to be included are marked as “O

32、“ (optional). The heading of the specification sheet shall indicate that it has been prepared in accordance with this part of ISO/IEC 11160. For every parameter, if any special instruction is not given, the name of the parameter of Table 1 shall be used without change. Non-applicable parameters may

33、be ignored, without changing the order of remaining parameters. Additional parameters may be adjacently inserted to the related parameter in Table 1 for the purpose of describing the function which is not covered by other parameters. For a parameter with voluminous description, it may be stated sepa

34、rately and may use a figure or a table. In such case, the caption of the figure or the table shall be identical with the name of parameter shown in Table 1. The “Remarks and examples“ column is provided for the persons who prepare the information sheet, and it is not intended to appear in the specif

35、ication sheet. The column includes informative examples and normative test methods and descriptions. Test methods to be applied, when not defined in other International Standards, are defined in this column. Whenever a capacity is given in sheets, the reference paper weight (g/m2) shall be specified

36、 Numbers attached to parameters are not normative but only for convenience. BS ISO/IEC 11160-2:2013ISO/IEC 11160-2:2013(E) ISO/IEC 2013 All rights reserved 3Table 1 Information to be included Parameter R/O Description of the entry Remarks and examples 1 General data 1.1 Printer class O Class 3 or Cl

37、ass 4 printer. See Annex A for description of classes.1.2 Machine name, model and/or model number R Product name, model number. 1.3 Type O State the machine type. State if the machine is portable, desk-top or floor-standing for the standard configuration, without optional devices.1.4 Printing method

38、 R The printing process used Such as ink-jet, thermal transfer, electro-photographic (laser), electrophotographic (LED). 1.5 Print resolution R Indicate horizontal and vertical dots per 25,4 mm (dpi), in this order. The maximum value shall be indicated in the order of horizontal and vertical. The de

39、sign capability of the machine to place the dots. Note that the theoretical writing resolution and the actual printing resolution may be different. If the dot density can be stepped up and down, all grades should be indicated. If technologies which can improve apparent resolution (line smoothing tec

40、hnology, bit depth control for each dot, etc.) are applied, resultant resolution, its method or trade name of such technology should be additionally indicated. 1.6 Tone O Indicate the available number of tone or colours in design theory. 2. Performance data 2.1 Warm-up time R Indicate both 1) and 2)

41、. 1) Send the print signal (i.e. click on PC), just after power-on. Measure time in minutes and/or seconds from the power-on to the completion of the first paper ejection. Warm-up time is described as the difference of the measured time and First print out time (2.2). 2) Send the print signal (i.e.

42、click on PC) from power save mode. Measure time in minutes and/or seconds from the print start to the completion of the first paper ejection. Warm-up time is described as the difference of the measured time and First print out time (2.2). If the value measured by 2) is equal to or longer than the va

43、lue of 1), indicate both values of 1) and 2). If the value of 1) is longer than the value 2), the value 2) is omissible. The results measured at 23 C should be indicated. Round off the results to integer number. In the case of less than 10 seconds round off the results to one decimal places and repo

44、rt two significant digits (e. g. from 5,35 to 5,4 seconds). Or after rounding up the results, it may report as “less than or equal to the figure“ or “ less than the figure“. If there is more than one power saver mode, indicate the results for each mode, or indicate the longest result. BS ISO/IEC 111

45、60-2:2013ISO/IEC 11160-2:2013(E) 4 ISO/IEC 2013 All rights reservedTable 1 (contd) Parameter R/O Description of the entry Remarks and examples 2.2 First print out time R The number of seconds between the initiation of the job until the complete exit of the first sheet The number of seconds shall be

46、described with the measuring condition and/or the name of international standard which was used for the measurement. 2.3 Continuous print speed O Measure the time (t in second) from just after complete discharge of the first sheet to end of discharge of the last sheet (nthsheet) for more than one mi

47、nute. The sustained throughput (S) is calculated using following equation: )1(60ntS For printers with duplex mode, measure the throughput at duplex printing mode. Indicate; For simplex print: pages/min For duplex print: images/min (doubling S obtained from the above equation) The Continuous Print Sp

48、eed shall not include the time for maintenance, such as cleaning. Significant digits for the sustained throughput (S in sheets/min) are, For less than 10 sheets/min : two digits“,0“ can be deleted and make integer number (for example, 6,0 to 6). For 10 pages/min or more and less than 100 pages/min:

49、two digits or three digits may be selected at companys option. For 100 pages/min or more : three digits Describe the value whether it is for monochrome, colour or both. For the test pattern, see Clause 4. 2.4 Printing productivity R State FSOT and ESAT parameters and a pointer to the full test report. ISO/IEC 24734. 3 Control Item 3.2 may be described together with item 3.1 at the end of 3.1. 3.1 Interface for hardware connection R State the hardware connections available. and the name of