BS ISO IEC 18000-64-2013 Information technology Radio frequency identification for item management Parameters for air interface communications at 860 MHz to 960 MHz Type D《信息技术 项目管.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO/IEC 18000-64:2012Information technology Radio frequency identification for item management Part 64: Parameters for air interface communications at 860 MHz to 960 MHz Type

2、D BS ISO/IEC 18000-64:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO/IEC 18000-64:2012. Together with BS ISO/IEC 18000-6:2013, BS ISO/IEC 18000-61:2012, BS ISO/IEC 18000-62:2012, and BS ISO/IEC 18000-63:2012, it supersedes BS ISO/IEC 18000-6:2010, which i

3、s withdrawn.The UK participation in its preparation was entrusted to Technical Committee IST/34, Automatic identification and data capture techniques.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the

4、 necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013.ISBN 978 0 580 75347 3ICS 35.040 Compliance with a British Standard cannot confer immunity from legal obligations.This British Stand

5、ard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2013.Amendments issued since publicationDate Text affectedBS ISO/IEC 18000-64:2012Reference numberISO/IEC 18000-64:2012(E)ISO/IEC 2012INTERNATIONAL STANDARD ISO/IEC18000-64First edition2012-07-15Infor

6、mation technology Radio frequency identification for item management Part 64: Parameters for air interface communications at 860 MHz to 960 MHz Type D Technologies de linformation Identification par radiofrquence (RFID) pour la gestion dobjets Partie 64: Paramtres de communications dune interface ra

7、dio entre 860 MHz et 960 MHz, Type D BS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including

8、photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in

9、 Switzerland ii ISO/IEC 2012 All rights reservedBS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) ISO/IEC 2012 All rights reserved iiiContents Page Foreword . v Introduction vi 1 Scope 1 2 Conformance . 1 2.1 Claiming conformance 1 2.2 Interrogator conformance and obligations . 2 2.3 Tag conformance

10、and obligations . 2 3 Normative references 2 4 Terms, definitions, symbols and abbreviated terms . 3 4.1 Terms and definitions . 3 4.2 Symbols 3 4.3 Abbreviated terms . 4 5 Overview . 5 5.1 Parameter tables 5 6 Type D . 8 6.1 Physical layer . 8 6.1.1 Interrogator power-up waveform . 8 6.1.2 Interrog

11、ator power-down 9 6.1.3 Frequency hopping carrier rise and fall times . 10 6.2 Protocol overview 11 6.2.1 General . 11 6.2.2 Protocol parameter values . 12 6.2.3 Tag arbitration . 12 6.2.4 Operating procedure . 13 6.2.5 TagMsg . 15 6.2.6 CW control . 16 6.2.7 Message encoding 16 6.2.8 Symbol modulat

12、ion . 17 6.2.9 Page modulation 17 6.2.10 Interrogator modulation detection . 20 6.3 Type D Data 20 6.3.1 General . 20 6.3.2 TID . 21 6.3.3 Structured data encoding . 23 6.3.4 Tag configuration 26 6.4 Encoding and decoding TID-S Tags 26 6.4.1 Encoding rules . 26 6.4.2 Decoding rules . 27 7 Sensor sup

13、port 28 7.1 Applicability . 28 7.2 Overview . 28 7.3 Simple Sensors 28 Annex A (informative) Calculation of 5-bit and 16-bit cyclic redundancy checks . 29 A.1 Example CRC-5 encoder/decoder 29 A.2 Example TID-S CRC-16 encoder/decoder . 30 A.3 Example TID-U CRC-16 encoder/decoder . 31 BS ISO/IEC 18000

14、-64:2012ISO/IEC 18000-64:2012(E) iv ISO/IEC 2012 All rights reservedAnnex B (normative) Simple Sensors Data Block .32 B.1 Simple sensor types 32 B.2 General bit-based rules .33 B.3 Temperature sensor with 14 C span 33 B.3.1 Monitored measurement span 33 B.3.2 Accuracy .33 B.3.3 Sampling regime 34 B.

15、3.4 High in-range limit level 34 B.3.5 Low in-range limit level .35 B.3.6 Monitor delay 35 B.3.7 High out-of-range alarm delay 36 B.3.8 Low out-of-range alarm delay .36 B.3.9 Alarms .37 B.4 Temperature sensor with 28 C span 38 B.4.1 Monitored measurement span 38 B.4.2 Accuracy .38 B.4.3 Sampling reg

16、ime 38 B.4.4 High in-range limit .38 B.4.5 Low in-range limit 38 B.4.6 Monitor delay 39 B.4.7 High out-of-range alarm delay 39 B.4.8 Low out-of-range alarm delay .39 B.4.9 Alarms .39 B.5 Relative humidity .39 B.5.1 Monitored measurement span 39 B.5.2 Accuracy .39 B.5.3 Sampling regime 40 B.5.4 High

17、in-range limit level 40 B.5.5 Low in-range limit level .40 B.5.6 Monitor delay 40 B.5.7 High out-of-range alarm delay 40 B.5.8 Low out-of-range alarm delay .40 B.5.9 Alarms .40 B.6 Impact .41 B.6.1 Monitored measurement span 41 B.6.2 Accuracy .41 B.6.3 Sampling regime 41 B.6.4 High in-range limit .4

18、1 B.6.5 Low in-range limit 41 B.6.6 Monitor delay 41 B.6.7 High out-of-range alarm delay 41 B.6.8 Low out-of-range alarm delay .42 B.6.9 Alarms .42 B.7 Tilt 42 B.7.1 Monitored measurement span 42 B.7.2 Accuracy .42 B.7.3 Sampling regime 42 B.7.4 High in-range limit .42 B.7.5 Low in-range limit 42 B.

19、7.6 Monitor delay 42 B.7.7 High out-of-range alarm delay 43 B.7.8 Low out-of-range alarm delay .43 B.7.9 Alarms .43 BS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) ISO/IEC 2012 All rights reserved vForeword ISO (the International Organization for Standardization) and IEC (the International Electrot

20、echnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical

21、 activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical

22、committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circula

23、ted to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. ISO/IEC 18000-64 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 31, Automatic identification and dat

24、a capture techniques. ISO/IEC 18000 consists of the following parts, under the general title Information technology Radio frequency identification for item management: Part 1: Reference architecture and definition of parameters to be standardized Part 2: Parameters for air interface communications b

25、elow 135 kHz Part 3: Parameters for air interface communications at 13,56 MHz Part 4: Parameters for air interface communications at 2,45 GHz Part 6: Parameters for air interface communications at 860 MHz to 960 MHz General Part 61: Parameters for air interface communications at 860 MHz to 960 MHz T

26、ype A Part 62: Parameters for air interface communications at 860 MHz to 960 MHz Type B Part 63: Parameters for air interface communications at 860 MHz to 960 MHz Type C Part 64: Parameters for air interface communications at 860 MHz to 960 MHz Type D Part 7: Parameters for active air interface comm

27、unications at 433 MHz BS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) vi ISO/IEC 2012 All rights reservedIntroduction This part of ISO/IEC 18000 describes a passive backscatter radio frequency identification (RFID) system that supports the following system capabilities: identification and communica

28、tion with multiple tags in the field; reading from individual tags; data integrity protection; tag-to-Interrogator communications link with error detection; support for both passive back-scatter tags with or without batteries. This part of ISO/IEC 18000 specifies the physical and logical requirement

29、s for a passive-backscatter, RFID system operating in the 860 MHz to 960 MHz frequency range. The system comprises Interrogators, also known as readers, and tags, also known as labels. An Interrogator transmits a continuous-wave (CW) RF signal in the 860 MHz to 960 MHz frequency range. The tag recei

30、ves operating energy from this RF signal and responds by modulating the reflection coefficient of its antenna, thereby backscattering an information signal to the Interrogator. Passive tags are those which receive all of their operating energy from the Interrogators RF waveform. If tags maintain a b

31、attery then they may operate using some passive principles; however, they do not necessarily get all their operating energy from the Interrogators RF waveform. This part of ISO/IEC 18000 contains an optional Tag Only Talks After Listening (TOTAL), an enhanced Tag Talks Only (TTO) technique. A Type D

32、 tag shall announce itself when it detects CW emitted by an Interrogator, only after it has detected the absence of ITF modulation as defined in ISO/IEC 18000 part 6. Type D uses Pulse-Position Encoding (PPE) or Miller encoding in the return link and does not define a dedicated forward link. Tags ma

33、y implement a forward link of one of the types defined in ISO/IEC 18000 part 6 in order to allow enhanced tag access techniques. The International Organization for Standardization (ISO) and International Electrotechnical Commission (IEC) draw attention to the fact that it is claimed that compliance

34、with this document may involve the use of patents concerning radio frequency identification technology. ISO and IEC take no position concerning the evidence, validity and scope of these patent rights. The holders of these patent rights have assured ISO and IEC that they are willing to negotiate lice

35、nces under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statements of the holders of these patent rights are registered with ISO and IEC. BS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) ISO/IEC 2012 All rights reserved viiInformat

36、ion on the declared patents may be obtained from: Contact details Patent Holder Legal Name: CISC Semiconductor Design+Consulting GmbH Contact for license application Name the tag responds by modulating the reflection coefficient of its antenna, thereby backscattering an information signal to the Int

37、errogator. The system is TOTAL, meaning that a tag modulates its antenna reflection coefficient with an information signal upon entering an Interrogators field after first listening for Interrogator modulation in order to determine if the system is ITF or not. In detail, this part of ISO/IEC 18000 c

38、ontains Type D. Type D is TOTAL based on Pulse Position Encoding or Miller M=2 encoded subcarrier. This part of ISO/IEC 18000 specifies physical interactions (the signalling layer of the communication link) between Interrogators and tags, Interrogator and tag operating procedures, the collision arbi

39、tration scheme used to identify a specific tag in a multiple-tag environment. 2 Conformance 2.1 Claiming conformance To claim conformance with this part of ISO/IEC 18000, an Interrogator or tag shall comply with all relevant clauses of this part of ISO/IEC 18000, except those marked as “optional”. T

40、he Interrogator or tag shall also operate within local radio regulations, which can further restrict operation. BS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) 2 ISO/IEC 2012 All rights reservedRelevant conformance test methods are provided in ISO/IEC TR 18047-6. Conformance can also require a lice

41、nse from the owner of any intellectual property utilized by said device. 2.2 Interrogator conformance and obligations To conform to this part of ISO/IEC 18000, an Interrogator shall support Type D; receive/demodulate a sufficient set of the electrical signals defined in the signalling layer of this

42、part of ISO/IEC 18000 to communicate with conformant tags; and operate within the applicable local regulations. To conform to this part of ISO/IEC 18000, an Interrogator may implement one of the types defined in ISO/IEC 18000 part 6 or proprietary commands in order to allow enhanced tag access techn

43、iques. 2.3 Tag conformance and obligations To conform to this part of ISO/IEC 18000, a tag shall: support Type D; operate over the frequency range from 860 MHz to 960 MHz, inclusive; modulate a backscatter signal only after listening for the absence of ITF modulation; and conform to local radio regu

44、lations. To conform to this part of ISO/IEC 18000, a tag may implement one of the types defined ISO/IEC 18000 part 6 or proprietary commands in order to allow enhanced tag access techniques. To conform to this part of ISO/IEC 18000, a tag shall not: modulate a backscatter signal before listening for

45、 the absence of ITF modulation as defined in ISO/IEC 18000 part 6. 3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docu

46、ment (including any amendments) applies. ISO/IEC 7816-6, ldentification cards lntegrated circuit cards Part 6: Interindustry data elements for interchange ISO/IEC 15961, Information technology Radio frequency identification (RFID) for item management Data protocol: application interface ISO/IEC 1596

47、2, Information technology Radio frequency identification (RFID) for item management Data protocol: data encoding rules and logical memory functions BS ISO/IEC 18000-64:2012ISO/IEC 18000-64:2012(E) ISO/IEC 2012 All rights reserved 3ISO/IEC 15963, Information technology Radio frequency identification

48、for item management Unique identification for RF tags ISO/IEC 18000-1, Information technology Radio frequency identification for item management Part 1: Reference architecture and definition of parameters to be standardized ISO/IEC 19762 (all parts), Information technology Automatic identification a

49、nd data capture (AIDC) techniques Harmonized vocabulary EPCglobal Tag Data Standards version 1.5 and above, EPCglobal Inc. 4 Terms, definitions, symbols and abbreviated terms 4.1 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 19762 (all parts) and the following apply. 4.1.1 collision arbitration algorithm used to prepare for and handle a dialogue between an Interrogator and a tag 4.1.2 physi