BS PD CEN TS 12201-7-2014 Plastics piping systems for water supply and for drainage and sewerage under pressure Polyethylene (PE) Guidance for the assessment of conformity《供水 压力条件下.pdf

1、BSI Standards PublicationPlastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE)Part 7: Guidance for the assessment of conformityPD CEN/TS 12201-7:2014National forewordThis Published Document is the UK implementation of CEN/TS 12201-7:2014. It superse

2、des DD CEN/TS 12201-7:2003 and DD CEN/TS 13244-7:2003, which are withdrawn.The UK participation in its preparation was entrusted by TechnicalCommittee PRI/88, Plastics piping systems, to Subcommittee PRI/88/2,Plastics piping for pressure applications.A list of organizations represented on this commi

3、ttee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 83045 7ICS 23.040.01

4、; 91.140.60Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was published under the authority of theStandards Policy and Strategy Committee on 31 March 2014.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMENTPD CEN

5、/TS 12201-7:2014TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 12201-7 February 2014 ICS 91.140.60; 23.040.01 Supersedes CEN/TS 12201-7:2003, CEN/TS 13244-7:2003English Version Plastics piping systems for water supply, and for drainage and sewerage under pressure - Po

6、lyethylene (PE) - Part 7: Guidance for the assessment of conformity Systmes de canalisations en plastique pour lalimentation en eau et pour les branchements et les collecteurs dassainissement avec pression - Polythylne (PE) - Partie 7: Guide pour lvaluation de la conformit Kunststoff-Rohrleitungssys

7、teme fr die Wasserversorgung und fr Entwsserungs- und Abwasserdruckleitungen - Polyethylen (PE) - Teil 7: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 19 August 2013 for provisional application. The period of validity of this CEN/TS is l

8、imited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN an

9、d to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national sta

10、ndards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, S

11、lovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reser

12、ved worldwide for CEN national Members. Ref. No. CEN/TS 12201-7:2014 EPD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 2 Contents Page Foreword 3 Introduction .4 1 Scope 6 2 Normative references 6 3 Terms and definitions .7 4 Abbreviated terms 10 5 General . 11 6 Testing and inspection . 11 6.1 Groupin

13、g 11 6.1.1 General . 11 6.1.2 Size groups 11 6.1.3 Fitting groups 11 6.1.4 Fitting types . 12 6.2 Type testing . 12 6.3 Batch release tests . 21 6.4 Process verification tests 24 6.5 Audit tests . 27 6.6 Indirect tests 30 6.7 One-off products and products produced in very low quantity 30 6.8 Mechani

14、cal fittings 30 6.9 Documentation 31 6.9.1 Type test results . 31 6.9.2 Test records 31 6.9.3 Technical file for certification purposes 31 A.1 General . 32 A.2 Change . 32 A.2.1 Change of base polymer 32 A.2.2 Change of grade 32 A.2.3 Change of pigment . 32 A.2.4 Change of additives other than pigme

15、nts 32 A.3 Type testing required for re-evaluation 33 A.3.1 Changes A.2.1 and A.2.3.1 . 33 A.3.2 Changes A.2.2.1, A.2.2.2, A.2.2.3, A.2.3.2, A.2.4.1, A.2.4.2 and A.2.4.3 33 B.1 Grouping 34 B.2 Type tests 34 B.3 Batch release tests . 36 B.4 Process verification tests 36 B.5 Audit tests . 36 Bibliogra

16、phy . 40 PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 3 Foreword This document (CEN/TS 12201-7:2014) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the ele

17、ments of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 12201-7:2003 and CEN/TS 13244-7:2003. EN 12201, Plastics piping systems for water supply, and for drainage and s

18、ewerage under pressure Polyethylene (PE), consists of the following parts: EN 12201-1, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 1: General EN 12201-2, Plastics piping systems for water supply, and for drainage and sewerage under pr

19、essure Polyethylene (PE) Part 2: Pipes EN 12201-3, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 3: Fittings EN 12201-4, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 4: Va

20、lves EN 12201-5, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 5: Fitness for purpose of the system CEN/TS 12201-7, Plastics piping systems for water supply, and for drainage and sewerage under pressure Polyethylene (PE) Part 7: Guidanc

21、e for the assessment of conformity This issue of CEN/TS 12201-7 takes into account the technical changes made in the revision of EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-5 and EN 12201-4, published in 2011 and respectively in 2012. Guidance for the assessment of conformity given in this document

22、 has been revised to reflect the changes made to test methods and requirements given in EN 12201-1, EN 12201-2, EN 12201-3, EN 12201-4 and EN 12201-5. Two new types of pipe have been introduced, i.e. coextruded pipes and peelable layer pipes. The sampling procedures and sampling frequencies for thes

23、e types of pipes have been introduced into the tables for TT, BRT, PVT and AT for pipes. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,

24、 Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Ki

25、ngdom. PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 4 Introduction Figure 1 and Figure 2 are intended to provide general information on the concept of testing and organization of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type testing (TT), batch r

26、elease test (BRT), process verification test (PVT), and audit test (AT), this part of EN 12201 details the applicable characteristics to be assessed as well as the frequency and sampling of testing. A typical scheme for the assessment of conformity of compounds, pipes, fittings, valves, joints or as

27、semblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment of conformity of compounds, pipes, fittings, valves, joints or assemblies by manufacturers, including certification, is given in Figure 2. PD

28、 CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 5 Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including certification PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 6 1 Scope This part of EN 12201 gives guidance for the assessment of conformity of compounds, products, join

29、ts and assemblies in accordance with the applicable part(s) of EN 12201 intended to be included in the manufacturers quality plan as part of the quality management system and for the establishment of certification procedures. It is recommended that the quality management system conforms to or is no

30、less stringent than the relevant requirements to EN ISO 9001 1. NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065 5, EN ISO/IEC 17021 3 or EN ISO/IEC 17020 2, as applicable. In conjunction with Parts 1 to 5 of EN 12201 (see Forew

31、ord) this document is applicable to polyethylene (PE) plastics piping systems for water supply, and for drainage and sewerage under pressure. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following cond

32、itions: a) allowable operating pressure, PFA, up to 25 bar1); b) an operating temperature of 20 C as a reference temperature; c) buried in the ground; d) sea outfalls; e) laid in water; f) above ground, including pipes suspended below bridges. NOTE 2 For applications operating at constant temperatur

33、e greater than 20 C and up to 40 C, see EN 12201-1:2011, Annex A. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation

34、practices or codes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 122

35、01-1:2011, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 1: General EN 12201-2:2011+A1:2013, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes EN 12201-3:2011+

36、A1:2012, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings 1) 1 bar = 0,1 MPa = 105Pa; 1 MPa = 1 N/mm2PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 7 EN 12201-4:2012, Plastics piping systems for water supply, and for drainag

37、e and sewerage under pressure - Polyethylene (PE) - Part 4: Valves EN 12201-5:2011, Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 5: Fitness for purpose of the system EN ISO 6259-1, Thermoplastics pipes - Determination of tensile pr

38、operties - Part 1: General test method (ISO 6259-1) EN ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient (ISO 12162) EN ISO 13477, Thermoplastics pipes for the conveyance of fluids - Determination of resistance t

39、o rapid crack propagation (RCP) - Small-scale steady-state test (S4 test) (ISO 13477) EN ISO 13478, Thermoplastics pipes for the conveyance of fluids - Determination of resistance to rapid crack propagation (RCP) - Full-scale test (FST) (ISO 13478) ISO 14236, Plastics pipes and fittings - Mechanical

40、-joint compression fittings for use with polyethylene pressure pipes in water supply systems ISO 17885, Plastics piping systems - Mechanical fittings for pressure piping systems - Specifications 2)ISO 21751, Plastics pipes and fittings - Decohesion test of electrofusion assemblies - Strip-bend test

41、3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12201-1:2011, EN 12201-2:2011+A1:2013, EN 12201-3:2011+A1:2012, EN 12201-4:2012 and EN 12201-5:2011 and the following apply. 3.1 certification body impartial body, governmental or non-governmental, posse

42、ssing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 5. 3.2 inspection body body that performs inspection Note 1 to entry: A

43、body can be an organization or part of an organization. Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 2. 3.3 testing laboratory laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products No

44、te 1 to entry: In the context of this part of EN 12201, the materials and products can be subjected to type testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable. 2) At the time of publication of this Technical Specification, this document is

45、 still in development and can be found under ISO/DIS 17885. PD CEN/TS 12201-7:2014CEN/TS 12201-7:2014 (E) 8 Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 4. 3.4 quality management system management system to direct and control an organization with regard to qual

46、ity Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 1. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type test TT test performed to prove that

47、the material, product, joint or assembly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are done regularly. 3.7

48、 batch release test BRT test performed by or on behalf of the manufacturer on a batch of compound or products, which is satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer on compound or products or joints or

49、assemblies at specific intervals to confirm that type tests originally performed on the compound or products or joints or assemblies continue to be valid and the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of compound or products and are carried out as a measure of process control. 3.9 audit test AT test performed by a test laboratory on behalf of an inspection