CAN CGSB-44 227-2008 Free-standing Office Desk Products and Components.pdf

1、CAN/CGSB-44.227-2008Supersedes CAN/CGSB-44.227-2000Free-standing Office Desk Products and ComponentsICS 97.140National Standard of CanadaThe CANADIAN GENERAL STANDARDS BOARD (CGSB), under whose auspices this National Standard of Canada has been developed is a government agency within Public Works an

2、d Government Services Canada. CGSB is engaged in the production of voluntary standards in a wide range of subject areas through the media of standards committees and the consensus process. The standards committees are composed of representatives of relevant interests including producers, consumers a

3、nd other users, retailers, governments, educational institutions, technical, professional and trade societies, and research and testing organizations. Any given standard is developed on the consensus of views expressed by such representatives. CGSB has been accredited by the Standards Council of Can

4、ada as a national standards-development organization. The standards that it develops and offers as National Standards of Canada conform to the criteria and procedures established for this purpose by the Standards Council of Canada. In addition to standards it publishes as national standards, CGSB pr

5、oduces standards to meet particular needs, in response to requests from a variety of sources in both the public and private sectors. Both CGSB standards and CGSB national standards are developed in conformance with the policies described in the CGSB Policy Manual for the Development and Review of St

6、andards. CGSB standards are subject to review and revision to ensure that they keep abreast of technological progress. Suggestions for their improvement, which are always welcome, should be brought to the notice of the standards committees concerned. Changes to standards are issued either as separat

7、e amendment sheets or in new editions of standards. An up-to-date listing of CGSB standards, including details on latest issues and amendments, and ordering instructions, is found in the CGSB Catalogue, which is published annually and is available without charge upon request. An electronic version,

8、CAT, is also available. More information is available about CGSB products and services at our Web site www.ongc-cgsb.gc.ca. Although the intended primary application of this standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the standard to ju

9、dge its suitability for their particular purpose. The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this stand

10、ard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any applicable regulatory requirements prior to its use. CGSB neither assumes nor accepts any responsibility for any injury or damage that may occur during o

11、r as the result of tests, wherever performed. Attention is drawn to the possibility that some of the elements of this Canadian standard may be the subject of patent rights. CGSB shall not be held responsible for identifying any or all such patent rights. Users of this standard are expressly advised

12、that determination of the validity of any such patent rights are entirely their own responsibility. Further information on CGSB and its services and standards may be obtained from: The Manager Strategic Standardization Division Canadian General Standards Board Gatineau, Canada K1A 1G6 The STANDARDS

13、COUNCIL OF CANADA is the coordinating body of the National Standards System, a coalition of independent, autonomous organizations working towards the further development and improvement of voluntary standardization in the national interest. The principal objects of the SCC are to foster and promote

14、voluntary standardization as a means of advancing the national economy, benefiting the health, safety and welfare of the public, assisting and protecting the consumer, facilitating domestic and international trade, and furthering international cooperation in the field of standards. A National Standa

15、rd of Canada (NSC) is a standard prepared or reviewed by an accredited Standards Development Organization (SDO) and approved by the SCC according to the requirements of CAN-P-2. Approval does not refer to the technical content of the standard; this remains the continuing responsibility of the SDO. A

16、 NSC reflects a consensus of a number of capable individuals whose collective interests provide, to the greatest practicable extent, a balance of representation of general interests, producers, regulators, users (including consumers), and others with relevant interests, as may be appropriate to the

17、subject in hand. It normally is a standard, which is capable of making a significant and timely contribution to the national interest. Those who have a need to apply standards are encouraged to use NSCs. These standards are subject to periodic review. Users of NSCs are cautioned to obtain the latest

18、 edition from the SDO, which publishes the standard. The responsibility for approving standards as National Standards of Canada rests with the: Standards Council of Canada 200-270 Albert Street Ottawa, Ontario K1P 6N7 How to order Publications: by telephone 819-956-0425 or 1-800-665-2472 by fax 819-

19、956-5740 by mail CGSB Sales Centre Gatineau, Canada K1A 1G6 in person Place du Portage Phase III, 6B1 11 Laurier Street Gatineau, Quebec by email ncr.cgsb-ongcpwgsc.gc.ca on the Web www.ongc-cgsb.gc.ca NATIONAL STANDARD OF CANADA CAN/CGSB-44.227-2008Supersedes CAN/CGSB-44.227-2000FREE-STANDING OFFIC

20、E DESK PRODUCTS AND COMPONENTSNATIONAL STANDARD OF CANADA CAN/CGSB-3.14-2006Prepared by the Approved by the Canadian General Standards Board Standards Council of CanadaPublished September 2008 by the Canadian General Standards Board Gatineau, Canada K1A 1G6 HER MAJESTY THE QUEEN IN RIGHT OF CANADA,

21、as represented by the Minister of Public Works and Government Services, the Minister responsible for the Canadian General Standards Board, (2008). No part of this publication may be reproduced in any form without the prior permission of the publisher.CANADIAN GENERAL STANDARDS BOARDCOMMITTEE ON FREE

22、-STANDING OFFICE DESK PRODUCTS AND COMPONENTS(Voting membership at date of approval)ChairmanComtois, M. Micom Laboratories Inc. (General Interest)General Interest CategoryDennie, J. Bodycote Materials Testing Canada Inc.Driscoll, R. Business and Institutional Furniture Manufacturers AssociationJantz

23、, J. IntertekSimon, T. Tanda Laboratories Inc.Stables, L. Workplace Safety and Insurance BoardProducer CategoryBarber, P. Compx WaterlooCarmona, P. Correctional Services Canada (CORCAN)Choo, C. Teknion Furniture SystemsDykstra, T. Haworth Inc.Figueiras, J. Standard Desk Division of Xception Internat

24、ional Inc.Musculus, J. Steelcase Inc.Parratt, B. The Global GroupRuster, R. Herman Miller Inc.User CategoryBach, A. Canada Revenue AgencyCook, B. City of EdmontonDenault, J. Industry CanadaDewling, D. Government of Newfoundland and LabradorGerrard, K. City of TorontoGitt, M. ConsultantLeblanc, D. Pu

25、blic Works and Government Services CanadaSecretary (Non-member)Khan, R. Canadian General Standards BoardAcknowledgment is made for the translation of this National Standard of Canada by the Translation Bureau of Public Works and Government Services Canada.CAN/CGSB-44.227-2008CAN/CGSB-44.227-2008 1CA

26、N/CGSB-44.227-2008Supersedes CAN/CGSB-44.227-2000CANADIAN GENERAL STANDARDS BOARDFREE-STANDING OFFICE DESK PRODUCTS AND COMPONENTS1. SCOPE1.1 This standard provides dimensional and performance requirements for safety, durability and structural adequacy of free-standing components of office desk prod

27、ucts.1.2 This standard also provides dimensional and adjustment requirements that respect generally accepted ergonomics guidelines or standards, such as those of CAN/CSA-ISO 9241-5-00, using NATICK/TR-89/044, 1988 as its source of anthropometric data.1.2.1 The dimensional and adjustment requirements

28、 aim to address the estimated needs of the 5th to 95th percentile of adult office workers when in the seated position.1.3 The selected methods for measuring desk products and components and for assessing their performance are based on the actual field and product-testing experience of the members of

29、 the Canadian General Standards Board Committee on Free-standing Office Desk Products and Components.1.4 Quantities and dimensions used in this standard are given in metric units with imperial equivalents shown in brackets where appropriate. The metric units shall be regarded as official in the even

30、t of dispute.1.5 The testing and evaluation of a product against this standard may require the use of materials and/or equipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to con

31、sult the appropriate authorities and to establish health and safety practices in conjunction with any applicable regulatory requirements prior to its use.2. REFERENCED PUBLICATIONS2.1 The following publications are referenced in this standard:2.1.1 Canadian Standards Association (CSA)CAN/CSA-ISO 924

32、1-5-00 Ergonomic Requirements for Office Work with Visual Display Terminals (VDTs) Part 5: Workstation Layout and Postural RequirementsC22.2 No. 9.0 General Requirements for LuminairesC22.2 No. 12 Portable Luminaires.2.1.2 American Association of Textile Chemists and Colorists (AATCC)EP 1 Grey Scale

33、 for Color Change.2.1.3 American National Standards Institute (ANSI)/BIFMA InternationalANSI/BIFMA X5.5-2008 Desk/Table Products TestsANSI/BIFMA X5.9-2004 Storage Units Tests.2 CAN/CGSB-44.227-20082.1.4 American National Standards Institute (ANSI)/National Electrical Manufacturers Association (NEMA)

34、ANSI/NEMA LD 3-2005 High-Pressure Decorative Laminates.2.1.5 ASTM InternationalC 297-04 Standard Test Method for Flat Tensile Strength of Sandwich ConstructionsD 523-89(1999) Standard Test Method for Specular GlossD 3359-02 Standard Test Methods for Measuring Adhesion by Tape TestD 3363-05 Standard

35、Test Method for Film Hardness by Pencil TestD 4060-01 Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser.2.1.6 BIFMA InternationalG1-2002 Ergonomics Guideline For VDT (Visual Display Terminal) Furniture Used In Office Work Spaces.2.1.7 International Organization fo

36、r Standardization (ISO)ISO/IEC 17025 General requirements for the competence of testing and calibration laboratories.2.1.8 U.S. Army NATICK Research, Development and Engineering CenterNATICK/TR-89/044, 1988 Anthropometric Survey of U.S. Army Personnel: Methods and Summary Statistics.2.2 A dated refe

37、rence in this standard is to the issue specified. An undated reference in this standard is to the latest issue, unless otherwise specified by the authority applying this standard. The sources are given in the Notes section.3. TERMINOLOGY3.1 The definitions in ANSI/BIFMA X5.5-2008 and X5.9-2004 and t

38、he following apply in this standard:Articulating Keyboard Support Surface (Support articul pour clavier)A vertically and horizontally continuously user-adjustable support surface for a computer keyboard, mouse and other input devices where the adjustment is provided by a jointed or segmented arm pro

39、viding retractability of the support surface complete with keyboard and mouse below the primary work surface to which it is attached.Roll-out Keyboard Support Surface (Support coulissant pour clavier)A horizontally user-adjustable work surface or tray that is used to support a computer keyboard and,

40、 in some instances, to provide space for a mouse.4. GENERAL REQUIREMENTS4.1 Tolerances Unless otherwise specified, the tolerances on test equipment, measuring equipment and loading devices shall be as follows:a. Test weights, 5%b. Forces, velocities and time, 5%c. Linear measurements, 1.5 mm (1/16 i

41、n.)CAN/CGSB-44.227-2008 3d. Angles, 5e. Levels, within 5 mm per metre (1/16 in. per linear foot)f. Cycles, all requirements are minimums.Test weights, forces, dimensions, angles, time, rates and velocities shall be targeted at the nominal values specified.4.2 Workmanship The assembled components sha

42、ll be uniform in quality, style, material and workmanship and shall be clean and free from any defects that may affect appearance, serviceability or safety. When assembled in any of the manufacturers recommended configurations, there shall be no unfinished edges or surfaces other than stainless stee

43、l when viewed in normal use positions. Metal edges, corners and parts with which the user is intended to come in contact shall be rounded or covered with protective caps. Lubricated parts, excluding drawer and roll-out keyboard shelf slides, shall be protected against accidental contact with the use

44、r, the users clothes or documents. Wood core surfaces shall have a balanced construction to minimize warping.4.3 Finish The specified finish (par. 10.1 a.) shall meet the requirements of Table 1. All exposed aluminum components shall be anodized, painted or otherwise treated to prevent oxidation.4.4

45、 Welds All welds shall be structurally sound, free from cracks and surface voids. They shall be clean, smooth, uniform in appearance and free from scale, flux, trapped foreign matter or any other inclusions that may be detrimental to the application of the primer or final finish.4.5 Safety Fixed, mo

46、vable or adjustable parts shall be constructed so that they cannot unintentionally become loose, dislodged or cause personal injury.4.6 Clearance Between Adjusting Surfaces The clearance between a vertical user-adjustable surface and any adjacent surface shall not be less than 25 mm (1 in.). A clear

47、ance less than 8 mm (0.3 in.) is acceptable where the clearance is maintained throughout the travel of the adjusting surface. Articulating keyboard support surfaces are exempt from this requirement.4.7 Interchangeability When specified (par. 10.1 b.), all components shall be interchangeable, right-t

48、o-left and left-to-right.4.8 Wood All visible solid wood shall be free from open knots.4.9 Cord and Cable Management When specified (par. 10.1 c.), the system shall provide cord and cable management capability. When specified (par. 10.1 c.), reusable covers shall be provided for each grommet to conc

49、eal the openings when not in use.4.10 Edges All work surface edges that are designed for a user to rest the forearm or wrist shall have a radius of at least 3 mm (0.12 in.).4.11 Recycled Material No limit is imposed on the amount of recycled material used in the manufacture of new components, and manufacturers are encouraged to use recyclable materials whenever possible and applicable. Where possible, all major plastic components should carry a composition code to facilitate recycling. The finished components