CAN CSA-C13256-2001 Water-source heat pumps - Testing and rating for performance - Part 1 Water-to-air and brine-to-air heat pumps (First Edition).pdf

1、National Standard of Canada CAN/CSA-C13256-l-01 ASSOCIATION / - International Standard IS0 13256-1: 1998 (first edition, 19984X3-15) has been adopted with Canadian deviations as CSA Standard CAN/CSA-C13256-1-01, which has been approved as a National Standard of Canada by the Standards Council of Can

2、ada. ISBN 1-5.5324-243-2 June 2001 Water-source heat pumps - Testing and rating for performance - Part 1: Water-to-air and brine-to-air heat pumps Pompes B chaleur 21 eau - Essais et d this remains the continuing responsibility of the accredited standards-development organization. Those who have a n

3、eed to apply standards are encouraged to use National Standards of Canada whenever practicable. These standards are subject to periodic review; therefore, users are cautioned to obtain the latest edition from the organization preparing the standard. The responsibility for approving National Standard

4、s of Canada rests with the Standards Council of Canada 270 Albert Street, Suite 200 Ottawa, Ontario, Kl P 6N7 Canada Les normes nationales du Canada sont publiees en versions frarqaise et anglaise. Although the intended primary application of this Standard is stated in its Scope, it is important to

5、note that it remains the responsibility of the users to judge its suitability for their particular purpose. Registered trade-mark of Canadian Standards Association CSA Standards Update ServiceCAN/CSA-C13256-1-01June 2001Title: Water-source heat pumps Testing and rating for performance Part 1: Water-

6、 to-air and brine- to-air heat pumpsPagination: 45 pages (CSA/1CSA/3, iv, and 37 text)To register for e-mail notification about any updates to this publicationgo to www.shop.csa.caclick on E-mail Services under MY ACCOUNTclick on CSA Standards Update ServiceThe List ID that you will need to register

7、 for updates to this publication is 2012250.If you require assistance, please e-mail techsupportcsa.ca or call 416-747-2233.Visit CSAs policy on privacy at www.csagroup.org/legal to find out how we protect your personal information.Blank pageCAN/CSA-C73256-7-07 Water-source heat pumps - Testing and

8、rating for performance - Part 7 : Water-to-air and brine-to-air heat pumps CAN/CSA-Cl3256-l-01 Water-source heat pumps - Testing and rating for perfiormance - Part 1: Water-to-air and brine-to-air heat pumps CSA Preface This is the first edition of CSA Standard CANKSA-(73256-1, Water-source heat pum

9、ps - Testing and rating for performance - Part 7 : Water-to-air and brine-to-air heat pumps, which is an adoption, with Canadian deviations, of the identically titled IS0 (International Organization for Standardization) Standard 13256-l :1998 (first edition, 1998-08-l 5). It is one of two Standards

10、that establish performance testing and rating criteria for factory-made residential, commercial and industrial, electrically driven, mechanical compression type heat pumps. The other Standard in the series is IS0 13256-2, Water-source heat pumps - Testing and rating for performance - Part 2: Water-t

11、o-water and brine-to-water heat pumps, which has been adopted as CANKSA-C13256-2-01. These two standards together supersede CANKSA-C446-94, Performance of Ground Source Heat Pumps, and CANKSA-C655M91, Performance Standard for Internal Water-Loop Heat Pump. This Standard was reviewed for Canadian ado

12、ption by the CSA Subcommittee on Ground and Water Source Heat Pumps under the jurisdiction of the CSA Technical Committee on Renewables and the Strategic Steering Committee on Performance, Energy Efficiency, and Renewables, and has been approved by the Technical Committee. A list of the members of t

13、he Technical Committee is available upon request. This Standard has been approved as a National Standard of Canada by the Standards Council of Canada. lune 200 7 0 Canadian Standards Association - 200 7 All rights reserved. No part of this publication may be reproduced in any form whatsoever without

14、 the prior permission of the publisher. IS0 material is reprinted with permission. Where the words “this International Standard” appear in the text, they should be interpreted as “this National Standard of Canada”. Inquiries regarding this National Standard of Canada should be addressed to Canadian

15、Standards Association 7 78 Rexdale Boulevard, Toronto, Ontario, Canada M9W 7 R3 7-800-463-6727 l 4 7 6-747-4044 www.csa.ca /une 200 7 0 Canadian Standards Association GSA/l CAN/CSA-C73256-7-07 Water-source beat pumps - Testing and rating for performance - Part 7: Water-to-air and brine-to-air heat p

16、umps CSA Foreword The Canadian Standards Association (CSA) develops standards under the name Canadian Standards Association, and provides certification and testing under the name CSA International. CSA International provides certification services for manufacturers who, under license from CSA, wish

17、to use the appropriate registered CSA Marks on certain products of their manufacture to indicate conformity with CSA Standards. CSA Certification for a number of products is provided in the interest of maintaining agreed-upon standards of quality, performance, interchangeability and/or safety, as ap

18、propriate. Where applicable, certification may form the basis for acceptance by inspection authorities responsible for enforcement of regulations. Where feasible, programs will be developed for additional products for which certification is desired by producers, consumers, or other interests. In per

19、forming its functions in accordance with its objectives, CSA does not assume or undertake to discharge any responsibility of the manufacturer or any other party. The opinions and findings of the Association represent its professional judgement given with due consideration to the necessary limitation

20、s of practical operation and state of the art at the time the Standard is processed. Products in substantial accord with this Standard but which exhibit a minor difference or a new feature may be deemed to meet the Standard providing the feature or difference is found acceptable utilizing appropriat

21、e CSA International Operating Procedures. Products that comply with this Standard shall not be certified if they are found to have additional features which are inconsistent with the intent of this Standard. Products shall not be certifiable if they are discovered to contravene applicable laws or re

22、gulations. Testing techniques, test procedures, and instrumentation frequently must be prescribed by CSA International in addition to the technical requirements contained in Standards of CSA. In addition to markings specified in the Standard, CSA International may require special cautions, markings,

23、 and instructions that are not specified by the Standard. Some tests required by CSA Standards may be inherently hazardous. The Association neither assumes nor accepts any responsibility for any injury or damage that may occur during or as the result of tests, wherever performed, whether performed i

24、n whole or in part by the manufacturer or the Association, and whether or not any equipment, facility, or personnel for or in connection with the test is furnished by the manufacturer or the Association. Manufacturers should note that, in the event of the failure of CSA International to resolve an i

25、ssue arising from the interpretation of requirements, there is an appeal procedure: the complainant should submit the matter, in writing, to the Secretary of the Canadian Standards Association. If this Standard is to be used in obtaining CSA Certification please remember, when making application for

26、 certification, to request all current Amendments, Bulletins, Notices, and Technical Information Letters that may be applicable and for which there may be a nominal charge. For such information or for further information concerning CSA Certification, please address your inquiry to Applications and C

27、ustomer Service, CSA International, 178 Rexdale Boulevard, Toronto, Ontario, Canada M9W 1 R3. - CSA/2 0 Canadian Standards Association lune 200 7 CAN/CSA-C73256-7-07 Water-source heat pumps - Testing and rating for performance - Part 7: Water-to-air and brine-to-air heat pumps Canadian Deviations 3.

28、8 Replace the term “energy efficiency ratio (EER)” in the title of Clause 3.8 and throughout the Standard with the term “Coefficient for performance for cooling (COP,)“. 3.9 Replace the term “coefficient of performance (COP)” in the title of Clause 3.9 and throughout the Standard with the term “Coef

29、ficient for performance for heating (COP,)“. Add the following Clause 8A Minimum values of COP, and COP, When tested in accordance with Clause 6, the heat pump shall have a minimum COP, and COP, as follows: Table 10A Type of System COP, COP, Open 4.75 at 15C 3.6 at 10C Closed-loop 3.93 at 25C 3.1 at

30、 0C internal loop 3.52 at 30C 4.2 at 20C Note: The temperature shown in the above table is for water entering the outdoor exchanger. june 200 7 0 Canadian Standards Association CSA/3 Blank pageINTERNATIONAL STANDARD IS0 13256-l First edition 1998-08-l 5 Water-source heat pumps - Testing and rating f

31、or performance - Part 1: Water-to-air and brine-to-air heat pumps Pompes 21 chaleur B eau - Essais et d i.e. the sum of: - the power input for operation of the compressor excluding additional electrical heating devices, - the power input of all control and safety devices of the equipment, and - the

32、proportional power input of the conveying devices for the transport of the heat transfer media through the heat pump only (e.g., fans, pumps, whether internal or external, whether provided with the equipment or not) (See 4.1.3 and 4.1.4.) 3.12 latent cooling capacity amount of latent heat that the e

33、quipment can remove from the conditioned space in a defined interval of time, in watts 3.13 sensible cooling capacity amount of sensible heat that the equipment can remove from the conditioned space in a defined interval of time, in watts 4 Rating and test conditions 4.1 Rating conditions for the de

34、termination of capacity 4.1 .l Standard ratings Standard ratings shall be established at the standard rating conditions specified in 4.2, using the test procedures described in clause 6. Standard ratings relating to cooling and heating capacities shall be net values, including the effects of circula

35、ting- fan heat, but not including supplementary heat. Standard efficiency ratings shall be based on the effective power input as defined in 3.11. 4.1.2 Power input of fans for heat pumps without duct connection In the case of heat pumps which are not designed for duct connection and which are equipp

36、ed with an integral fan, all power consumed by the fans shall be included in the effective power input to the heat pump. 4.1.3 Power input of fans for heat pumps with duct connection 4.1.3.1 If no fan is provided with the heat pump, a fan power adjustment is to be included in the effective power inp

37、ut to the heat pump, using the following formula: 4fa = q x AP r7 where rl = 0,3 x 103 by convention; Ap is the measured internal static pressure difference, in pascals; 9 is the nominal airflow rate, in litres per second. This value shall be added to the heating capacity and subtracted from the coo

38、ling capacity. IS0 13256-l :1998( E) 0 IS0 4.1.3.2 If a fan is an integral part of a heat pump, only the portion of the fan power required to overcome the internal resistance shall be included in the effective power input to the heat pump. The fraction which is to be excluded from the total power co

39、nsumed by the fan shall be calculated using the following formula: .- 4fa = q x ir, rl where Aa is the fan power adjustment, in watts; rl = 0,3 x 103 by convention; 9 is the nominal airflow rate, in litres per second. This value shall be subtracted from the heating capacity and added to the cooling

40、capacity. 4.1.4 Power input of liquid pumps 4.1.4.1 If no liquid pump is provided with the heat pump, a pump power adjustment is to be included in the effective power consumed by the heat pump, using the following formula: where rl = 0,3 x 103 by convention; Ap is the measured internal static pressu

41、re difference, in pascals; 9 is the nominal fluid flow rate, in litres per second. 4.1.4.2 If a liquid pump is an integral part of the heat pump, only the portion of the pump power required to overcome the internal resistance shall be included in the effective power input to the heat pump. The fract

42、ion which is to be excluded from the total power consumed by the pump shall be calculated using the following formula: 4 x AP pa= - r7 where ha is the pump power adjustment, in watts; rl = 0,3 x 103 by convention; Ap is the measured external static pressure difference, in pascals; 9 is the nominal f

43、luid flow rate, in litres per second. 4.1.5 Airflow rates 4.1.5.1 All standard ratings shall be determined at airflow rates as described below. All airflow rates shall be expressed as litres per second of standard air as defined in 3.10. - 4.1.5.2 Ducted heat pumps which have integral fans shall be

44、tested at the airflow rates specified by the manufacturer, or those obtained at zero external static pressure difference, whichever provides the lower airflow rate. IS0 IS0 13256-l :1998(E) 4.1.5.3 Ducted heat pumps which do not have integral fans, but which are tested in combination with a device e

45、mploying a fan, shall be tested as described in 4.1.5.2. Ducted heat pumps which do not have integral fans but which are rated for general use with a variety of air moving devices, shall be tested at the airflow rates specified by the manufacturer in the published ratings. However, the pressure drop

46、 across the indoor coil assembly and the recommended enclosures and attachment means shall not exceed 75 Pa. 4.1.5.4 Non-ducted heat pumps shall be tested at the airflow rates obtained at zero external static pressure difference. 4.1.5.5 The manufacturer shall specify a single airflow rate for all t

47、ests required in this part of IS0 13256 unless automatic adjustment of airflow rate is provided by the equipment. A separate control signal output for each step of airflow rate shall be considered as an automatic adjustement. 4.1.6 Liquid flow rates 4.1.6.1 All standard ratings shall be determined a

48、t a liquid flow rate described below, expressed as litres per second. 4.1.6.2 Heat pumps with integral liquid pumps shall be tested at the liquid flow rates specified by the manufacturer or those obtained at zero external static pressure difference, whichever provides the lower liquid flow rate. 4.1

49、.6.3 Heat pumps without integral liquid pumps shall be tested at the flow rates specified by the manufacturer. 4.1.6.4 The manufacturer shall specify a single liquid flow rate for all of the tests required in this part of IS0 13256 unless automatic adjustment of the liquid flow rate is provided by the equipment. A separate control signal output for each step of liquid flow rate will be considered as an automatic adjustment. 4.1.7 Requirements for separated assemblies In the case of heat pumps consisting of separate matched assemblies, the following installation procedu