CAN CSA-C22 2 NO 60745-2-12A-2008 Amendment 1 Hand-held motor-operated electric tools - Safety - Part 2-12 Particular requirements for concrete vibrators (Second Edition).pdf

1、(IEC 60745-2-12:2003, IDT)CAN/CSA-C22.2 No. 60745-2-12-05Amendment 1Hand-held motor-operated electric tools Safety Part 2-12: Particular requirements for concrete vibratorsAmendment 1:2008 (MOD) to National Standard of CanadaBlank pageCanadian Standards AssociationAmendment 1:2008 (MOD) to National

2、Standard of CanadaCAN/CSA-C22.2 No. 60745-2-12-05, Second Edition(IEC 60745-2-12:2003, IDT)Underwriters Laboratories Inc.UL 60745-2-12Second EditionAmendment 1Hand-held motor-operated electric tools Safety Part 2-12:Particular requirements for concrete vibratorsAmendment publication date: OCTOBER 17

3、, 2008This amendment is an adoption of IEC Amendment 1 (2008) to publication IEC 60745-2-12, Second Edition (2003).ANSI/UL 60745-2-12-2008 2008Canadian Standards AssociationAll rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the p

4、ublisher.Amendment 1:2008 to International Standard IEC 60745-2-12:2003 has been adopted with National Differences (MOD) as Amendment 1:2008 to CAN/CSA-C22.2 No. 60745-2-12-05. This Amendment was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdi

5、ction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee.October 2008Copyright 2008 Underwriters Laboratories Inc.Revisions of this Standard w

6、ill be made by issuing revised or additional pages bearing their date of issue. A UL Standard is current only if it incorporates the most recently adopted revisions, all of which are itemized on the transmittal notice that accompanies the latest set of revised requirements. The most recent designati

7、on of ANSI/UL 60745-2-12 as an American National Standard (ANSI) occurred on October 17, 2008.This ANSI/UL Standard for Safety, which consists of the Second edition with revisions through October 17, 2008, is under continuous maintenance, whereby each revision is ANSI approved upon publication. Comm

8、ents or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/.OCTOBER 17, 2008 Amendment 1:2008 to CAN/CSA-C22.2 No. 60745-2-12-05 UL 6074

9、5-2-12 iiiCanadian/US National Differences24.4DV DR Modification: Replace Clause 24.4 of this Part 2 with the following:A supply cord shall be Type SOW, STW, or equivalent that is oil- and weather-resistant in accordance with the National Electrical Code, NFPA 70, and the Canadian Electrical Code, P

10、art I, CSA C22.1.Blank pageIEC 60745-2-12Edition 2.0 2008-05INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held motor-operated electric tools Safety Part 2-12: Particular requirements for concrete vibrators Outils lectroportatifs moteur Scurit Partie 2-12: Rgles particulires pour les vibreurs bton

11、IEC60745-2-12A1:2008 AMENDMENT 1 AMENDEMENT 1 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including ph

12、otocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your

13、local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les micro

14、films, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre p

15、ays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electron

16、ic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The I

17、EC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Publish

18、ed details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in ad

19、ditional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec

20、.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des

21、publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la

22、CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications

23、 de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en angla

24、is et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez

25、 des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60745-2-12Edition 2.0 2008-05INTERNATIONAL STANDARD NORME INTERNATIONALEHand-held motor-operated electric tools Safety Part 2-12: Particular requirements for concrete

26、 vibrators Outils lectroportatifs moteur Scurit Partie 2-12: Rgles particulires pour les vibreurs bton INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE FICS 25.140.20 PRICE CODECODE PRIXAMENDMENT 1 AMENDEMENT 1 2 60745-2-12 Amend. 1 IEC:2008 FOREWORD This amendmen

27、t has been prepared by subcommittee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. The text of this amendment is based on the following documents: FDIS Report on voting 61F/737/FDIS 61F/757/RVD Full inform

28、ation on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. With this amendment, this Part 2 is established on the basis of the fourth edition (2006) of IEC 60745-1, Hand-held motor-operated electric tools Safety Part 1: General requireme

29、nts. Main changes include editorial modifications to match with the fourth edition of IEC 60745-1 and clarifications in Annex K. The committee has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web sit

30、e under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. _ 1 Scope Replace the existing text of Clause 1 by the following: This clause of Part 1 is applicable, except as f

31、ollows: Addition: This standard applies to concrete vibrators. 3 Definitions Change the title of Clause 3 to read: 3 Terms and definitions Replace the existing text of 3.101 by the following: Amendment 1:2008 to CAN/CSA-C22.2 No. 60745-2-12-0560745-2-12 Amend. 1 IEC:2008 3 3.101 concrete vibrator to

32、ol intended for compacting concrete. The active part (vibrator bottle) of the vibrator performs low-amplitude vibrations and is immersed into the mass of concrete to be vibrated. Concrete vibrators may be of one of the following designs: a) the motor and the vibrating mechanism are inside the vibrat

33、or bottle to which the part containing the mains switch or a power converter and switch handle assembly is connected by means of a long flexible hose containing the interconnecting cable. The long flexible hose may be used as the handle (see Figure 101); b) only the vibrator mechanism is inside the

34、vibrator bottle to which a separate portable unit, comprising the motor, the handle and the mains switch, is connected by means of a long flexible hose containing a flexible shaft (see Figure 102) 14 Moisture resistance Replace the existing text of 14.1 by the following: 14.1 Replacement of the firs

35、t paragraph: For design a) as defined in 3.101, the enclosure of all parts and the cable entry shall be IPX7. During the relevant test of this subclause, the part containing the switch or the power converter and switch handle assembly is placed in the normal position of use, the hose, if any, being

36、attached correctly to it. For design b) as defined in 3.101, the motor unit shall be IPX4. During the relevant test of this subclause, the motor unit is placed in the most unfavourable position occurring during normal use. The isolating transformer or the motor-generator shall be IPX4. 18 Abnormal o

37、peration Replace the existing text of 18.12 by the following: 18.12 This subclause is not applicable. Replace the last paragraph of 18.101 by the following: After the concrete vibrator has been allowed to cool down to approximately room temperature, it shall withstand an electric strength test as sp

38、ecified in 15.2. For concrete vibrators having the motor in the bottle, the test voltage across basic insulation is, however, reduced to 1 000 V for tools other than those of class III. 20 Mechanical strength Add the following new subclause: 20.5 This subclause is not applicable. Replace the last pa

39、ragraph of 20.101 by the following: Amendment 1:2008 to CAN/CSA-C22.2 No. 60745-2-12-05 4 60745-2-12 Amend. 1 IEC:2008 Moreover, the concrete vibrator shall withstand an electric strength test as specified in 15.2. For concrete vibrators having the motor in the bottle, the test voltage across basic

40、insulation is, however, reduced to 1 000 V for tools other than those of class III. 21 Construction Add the following new subclause: 21.32 This subclause is not applicable. 24 Supply connection and external flexible cords Replace the existing text of 24.4 by the following: 24.4 Modification: Instead

41、 of the first paragraph, the following applies: Supply cords shall be at least heavy polychloroprene sheathed flexible cable (60245 IEC 66). Replace the existing text of 24.101 by the following: 24.101 The supply cable attached to the part containing the mains switch shall have a length: of at least

42、 5 m for designs a) as defined in 3.101; of not more than 0,5 m or of at least 5 m for design b) as defined in 3.101. Compliance is checked by measuring the length of the cable, including any cord guard, between the plug and the point where the cable enters the part containing the mains switch. Add

43、the following figures: 1 2 3 4 IEC 739/08 Key 1 electric supply cable 2 power converter and switch with handle 3 part containing the mains switch 4 vibrator bottle with motor Figure 101 Typical design a) of a concrete vibrator Amendment 1:2008 to CAN/CSA-C22.2 No. 60745-2-12-0560745-2-12 Amend. 1 IE

44、C:2008 5 1 2 3 4 IEC 740/08 Key 1 electric supply cable 2 motor unit with switch 3 flexible shaft 4 vibrator bottle Figure 102 Typical design b) of a concrete vibrator Annexes Replace the existing texts of Annexes K and L by the following: Annex K (normative) Battery tools and battery packs K.1 Addi

45、tion: All clauses of this Part 2 apply unless otherwise specified in this annex. K.10.1 This subclause of Part 2 is not applicable. K.12.4 This subclause of Part 2 is not applicable. K.14.1 This subclause of Part 2 is not applicable. K.17.2 This subclause of Part 2 is not applicable. K.18.101 This s

46、ubclause of Part 2 is not applicable. K.20.3 This subclause of Part 2 is not applicable. K.20.101 This subclause of Part 2 is not applicable. K.21.16 This subclause of Part 2 is not applicable. Amendment 1:2008 to CAN/CSA-C22.2 No. 60745-2-12-05 6 60745-2-12 Amend. 1 IEC:2008 K.24.4 This subclause o

47、f Part 2 is not applicable. K.24.101 This subclause of Part 2 is not applicable. Annex L (normative) Battery tools and battery packs provided with mains connection or non-isolated sources L.1 Addition: All clauses of this Part 2 apply unless otherwise specified in this annex. _ Amendment 1:2008 to C

48、AN/CSA-C22.2 No. 60745-2-12-05ICS 25.140.20 PRINTED IN CANADAIMPRIMEAU CANADA100%The Canadian Standards Association (CSA) prints its publications on Rolland Enviro100, which contains 100% recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using bioga

49、s energy.Copyright NoticeThis Amendment to the International Standard contains information copyright protected by theInternational Electrotechnical Commission (IEC). Except as permitted under the laws of Canada, no extract ofthis Amendment to the International Standard may be reproduced, stored in any retrieval system, ortransmitted in any form or by any means, electron