CAN CSA-ISO IEC 14443-1A-2013 Identification cards - Contactless integrated circuit cards - Proximity cards - Part 1 Physical characteristics AMENDMENT 1 Additional PICC classes.pdf

1、Identification cards Contactless in tegrated circuit cards Proximity cards Part 1: Physical characteristics AMENDMENT 1: Additional PICC classes Amendment 1:2013 (IDT) toNational Standard of CanadaCAN/CSA-ISO/IEC 14443-1-09(ISO/IEC 14443-1:2008, IDT)NOT FOR RESALE. / PUBLICATION NON DESTINE LA REVEN

2、TE.Standards Update ServiceAmendment 1:2013 toCAN/CSA-ISO/IEC 14443-1-09January 2013Title:Identification cards Contactless integr ated circuit cards Proximity cards Part 1: Physical characteristics AMENDMENT 1: Additional PICC classes Pagination:10 pages (iii preliminary and 7 text)To register for e

3、-mail notification about any updates to this publicationgo to shop.csa.caclick on CSA Update ServiceThe List ID that you will need to register for updates to this publication is 2422244.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on p

4、rivacy at csagroup.org/legal to find out how we protect your personal information.Reference numberISO/IEC 14443-1:2008/Amd.1:2012(E)ISO/IEC 2012INTERNATIONAL STANDARD ISO/IEC14443-1Second edition2008-06-15AMENDMENT 12012-05-01Identification cards Contactless integrated circuit cards Proximity cards

5、Part 1: Physical characteristics AMENDMENT 1: Additional PICC classes Cartes didentification Cartes circuit(s) intgr(s) sans contact Cartes de proximit Partie 1: Caractristiques physiques AMENDEMENT 1: Classes de PICC additionnelles ISO/IEC 14443-1:2008/Amd.1:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO

6、/IEC 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in

7、the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org ii ISO/IEC 2012 All rights reservedAmendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) ISO/IEC 2012 A

8、ll rights reserved iiiForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International St

9、andards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO a

10、nd IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committe

11、e is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the p

12、ossibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO/IEC 14443-1:2008 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Sub

13、committee SC 17, Cards and personal identification. Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) ISO/IEC 2012 All rights reserved 1Identification cards Contactless integrated circuit cards Proximity cards Part 1: Physi

14、cal characteristics AMENDMENT 1: Additional PICC classes Page 1, Normative references Replace “ISO/IEC 10373-6” with “ISO/IEC 10373-6:2011”. Add the following normative reference: “ISO/IEC 14443-2, Identification cards Contactless integrated circuit cards Proximity cards Part 2: Radio frequency powe

15、r and signal interface” Page 2, 4.4 Replace the paragraph with the following: “If the PICC meets the requirements of one particular class as specified in Annex A, then the PICC, whichever form the PICC has according to 4.1, shall continue to operate as intended after continuous exposure to a magneti

16、c field of an average level of 4/3 times Hmaxat 13,56 MHz as specified in ISO/IEC 14443-2:2010/Amd.2:1), 6.2 for this class. The averaging time is 30 seconds and the maximum level of the magnetic field is limited to 8/5 times Hmax. If the PICC does not claim to meet the requirements of one particula

17、r class as specified in Annex A, then the PICC, whichever form the PICC has according to 4.1, shall continue to operate as intended after continuous exposure to a magnetic field of an average level of 10 A/m (rms) at 13,56 MHz. The averaging time is 30 seconds and the maximum level of the magnetic f

18、ield is limited to 12 A/m (rms).” Page 3, Annex A Replace Annex A with the following: 1)To be published. Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) 2 ISO/IEC 2012 All rights reservedAnnex A (normative) PICC class definitions A.1 “Class 1” A “Class 1” PICC shall

19、fulfil the requirements in A.1.1 and A.1.2. The support of “Class 1” PICCs is mandatory for PCDs. A.1.1 Antenna location The antenna of a “Class 1” PICC shall be located within a zone defined by two rectangles, as specified in Figure A.1: external rectangle: 81 mm 49 mm; internal rectangle: 64 mm 34

20、 mm, centered in the external rectangle, with 3 mm corner radii; except for the connections to the ends of the antenna coil, with a maximum area of 300 mm2. 81 mm64 mmR 3 mmPICC antenna zoneFigure A.1 Location of the antenna of the “Class 1” PICC The antenna of a PICC with ID-1 dimensions (as define

21、d in ISO/IEC 7810 or ISO/IEC 15457-1) should be centered. A.1.2 Electrical requirement The “Class 1” PICC shall also pass the PICC maximum loading effect test defined in ISO/IEC 10373-6:2011/Amd.1:2012, 7.2.4. Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) ISO/IEC 2

22、012 All rights reserved 3A.2 “Class 2” A “Class 2” PICC shall fulfil the requirements in A.2.1 and A.2.2. The support of “Class 2” PICCs is mandatory for PCDs. A.2.1 Antenna location The antenna of a “Class 2” PICC shall be located within a zone defined by two rectangles, as specified in Figure A.2:

23、 external rectangle: 81 mm 27 mm; internal rectangle: 51 mm 13 mm, located at 7 mm and 8,5 mm from the external rectangle, with 3 mm corner radii; except for the connections to the ends of the antenna coil, with a maximum area of 300 mm2. 27 mm13mm81 mm51 mmR 3 mmPICC antenna zone8,5 mm7mmFigure A.2

24、 Location of the antenna of the “Class 2” PICC A.2.2 Electrical requirement The “Class 2” PICC shall also pass the PICC maximum loading effect test defined in ISO/IEC 10373-6:2011/Amd.1:2012, 7.2.4. Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) 4 ISO/IEC 2012 All r

25、ights reservedA.3 “Class 3” A “Class 3” PICC shall fulfil the requirements in A.3.1 and A.3.2. The support of “Class 3” PICCs is mandatory for PCDs. A.3.1 Antenna location The antenna of a “Class 3” PICC shall be located within a zone defined by either: external rectangle: 50 mm 40 mm; internal rect

26、angle: 35 mm 24 mm, centered in the external rectangle, with 3 mm corner radii; or external circle with diameter 50 mm; internal circle with diameter 32 mm, concentric with the external circle; as specified in Figure A.3, except for the connections to the ends of the antenna coil, with a maximum are

27、a of 300 mm2. 40 mm 24 mmPICC antenna zone50 mm 32 mmFigure A.3 Location of the antenna of the “Class 3” PICC A.3.2 Electrical requirement The “Class 3” PICC shall also pass the PICC maximum loading effect test defined in ISO/IEC 10373-6:2011/Amd.1:2012, 7.2.4. Amendment 1:2013 to CAN/CSA-ISO/IEC 14

28、443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) ISO/IEC 2012 All rights reserved 5A.4 “Class 4” A “Class 4” PICC shall fulfil the requirements in A.4.1 and A.4.2. The support of “Class 4” PICCs is optional for PCDs. A.4.1 Antenna Location The antenna of a “Class 4” PICC shall be located within a zone def

29、ined by either: external rectangle: 50 mm 27 mm; internal rectangle: 35 mm 13 mm, centered in the external rectangle, with 3 mm corners radii; or external circle with diameter 41 mm; internal circle with diameter 24 mm, concentric with the external circle; as specified in Figure A.4, except for the

30、connections to the ends of the antenna coil, with a maximum area of 300 mm2. 27 mm 13mmFigure A.4 Location of the antenna of the “Class 4” PICC A.4.2 Electrical requirement The “Class 4” PICC shall also pass the PICC maximum loading effect test defined in ISO/IEC 10373-6:2011/Amd.1:2012, 7.2.4. Amen

31、dment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) 6 ISO/IEC 2012 All rights reservedA.5 “Class 5” A “Class 5” PICC shall fulfil the requirements in A.5.1 and A.5.2. The support of “Class 5” PICCs is optional for PCDs. A.5.1 Antenna location The antenna of a “Class 5” PICC

32、shall be located within a zone defined by either: external rectangle: 40,5 mm 24,5 mm; internal rectangle: 25 mm 10 mm, centered in the external rectangle, with 3 mm corners radii; or external circle with diameter 35 mm; internal circle with diameter 18 mm, concentric with the external circle; as sp

33、ecified in Figure A.5, except for the connections to the ends of the antenna coil, with a maximum area of 300 mm2. 24,5 mm40,5 mmPICC antenna zone10 mm25 mmR 3 mmFigure A.5 Location of the antenna of the “Class 5” PICC A.5.2 Electrical requirement The “Class 5” PICC shall also pass the PICC maximum

34、loading effect test defined in ISO/IEC 10373-6:2011/Amd.1:2012, 7.2.4. Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:2012(E) ISO/IEC 2012 All rights reserved 7A.6 “Class 6” A “Class 6” PICC shall fulfil the requirements in A.6.1 and A.6.2. The support of “Class 6” PICCs is

35、 optional for PCDs. A.6.1 Antenna location The antenna of a “Class 6” PICC shall be located within a zone defined by either a rectangle of dimensions 25 mm 20 mm or a circle of 25 mm diameter, as specified in Figure A.6, except for the connections to the ends of the antenna coil, with a maximum area

36、 of 300 mm2. 20 mmFigure A.6 Location of the antenna of the “Class 6” PICC A.6.2 Electrical requirement The “Class 6” PICC shall also pass the PICC maximum loading effect test defined in ISO/IEC 10373-6:2011/Amd.1:2012, 7.2.4. Amendment 1:2013 to CAN/CSA-ISO/IEC 14443-1-09ISO/IEC 14443-1:2008/Amd.1:

37、2012(E) ICS 35.240.15 ISO/IEC 2012 All rights reserved Copyright NoticeThis Amendment to the International Standard contains information copyright protected by t he International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). Except as permitted under

38、 the laws of Canada, no extract of this Amendment to the International Standard may be reproduced, stored in any retrieval system, or transmitted in any form or by any means, electronic, photocopying, recording, or otherwise, without prior permission from the Standards Council of Canada (SCC). Reque

39、sts for permission to reproduce this Amendment to the International Standard or parts thereof should be addressed to Manager, Technical Document Centre Standards Council of Canada 270 Albert Street, Suite 200 Ottawa, Ontario K1P 6N7 The Canadian adoption of this Amendment to the International Standa

40、rd contains information copyright protected by CSA Group. All rights reserved. No part of this adopted Amendment may be reproduced in any form whatsoever without the prior permission of the publisher. ISO/IEC material is reprinted with permission. Requests for permission to reproduce this adopted Am

41、endment or parts thereof should be addressed to Manager, Sales CSA Group 5060 Spectrum Way, Suite 100 Mississauga, Ontario L4W 5N6Copyright violators will be prosecuted to the full extent of the law.PRINTED IN CANADAIMPRIMEAU CANADA100%CSA Group prints its publications on Rolland Enviro100, which contains 100%recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using biogas energy.