CAN CSA-ISO IEC 14496-4N-2008 Information technology - Coding of audio-visual objects - Part 4 Conformance testing AMENDMENT 14 BSAC conformance.pdf

1、 Reference numberISO/IEC 14496-4:2004/Amd.14:2007(E)ISO/IEC 2007Information technology Coding of audio-visual objects Part 4: Conformance testing AMENDMENT 14: BSAC conformance Technologies de linformation Codage des objets audiovisuels Partie 4: Essai de conformit AMENDEMENT 14: Conformit BSAC Amen

2、dment 14:2008 toNational Standard of CanadaCAN/CSA-ISO/IEC 14496-4:06Amendment 14:2007 to International Standard ISO/IEC 14496-4:2004 has been adopted withoutmodification (IDT) as Amendment 14:2008 to CSA Standard CAN/CSA-ISO/IEC 14496-4:06. ThisAmendment was reviewed by the CSA Technical Committee

3、on Information Technology (TCIT) under thejurisdiction of the Strategic Steering Committee on Information Technology and deemed acceptable for use inCanada.September 2008 International Organization for Standardization (ISO), 2007. All rights reserved. International Electrotechnical Commission (IEC),

4、 2007. All rights reserved. NOT FOR RESALE. ISO/IEC 14496-4:2004/Amd.14:2007(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2007 All rights reserved. Unless required for installation or otherwise specified, no part of these CD-ROMs may be reproduced, stored in a retrieval system or transmitted in any form

5、or by any means without prior permission from ISO. Requests for permission to reproduce this product should be addressed to ISO copyright office Case postale 56 CH-1211 Geneva 20 Switzerland Internet copyrightiso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators

6、 may be prosecuted. ii ISO/IEC 2007 All rights reservedPDF disclaimer PDF files may contain embedded typefaces. In accordance with Adobes licensing policy, such files may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the compute

7、r performing the editing. In downloading a PDF file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create

8、 the PDF file(s) constituting this document can be found in the General Info relative to the file(s); the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the files are suitable for use by ISO member bodies. In the unlikely event that a problem relating t

9、o them is found, please inform the Central Secretariat at the address given below. ISO/IEC 14496-4:2004/Amd.14:2007(E) Installation If this publication has been packaged as a zipped file, do NOT open the file from the CD-ROM, but copy it to the desired location in your local environment. Once the fi

10、le has been copied to your local environment, open the file to unzip its contents. For compound documents (e.g. HTML documents comprising several files or folders, documents that have been subdivided owing to the total file size, etc.), in order for the links between documents to function properly,

11、the file and folder names must be maintained and all the files stored in the same folder. Where the zip file contains a Readme file, it is essential to consult this file to understand the way in which the document has been structured. ISO/IEC 2007 All rights reserved iiiThese CD-ROMs contain: 1) the

12、 publication ISO/IEC 14496-4:2004/Amd.14:2007 in portable document format (PDF), which can be viewed using Adobe Acrobat Reader; 2) conformance bitstreams relevant to ISO/IEC 14496-4:2004/Amd.14:2007. Adobe and Acrobat are trademarks of Adobe Systems Incorporated. ISO/IEC 14496-4:2004/Amd.14:2007(E)

13、 iv ISO/IEC 2007 All rights reservedISO/IEC 14496-4:2004/Amd.14:2007(E) ISO/IEC 2007 All rights reserved vISO/IEC 14496-4:2004/Amd.14:2007(E) vi ISO/IEC 2007 All rights reservedISO/IEC 14496-4:2004/Amd.14:2007(E) ISO/IEC 2007 All rights reserved viiINTERNATIONAL STANDARD Disk 1 of 2 Reference number

14、 ISO/IEC 14496-4:2004/ Amd.14:2007(E) ICS 35.040 ISO/IEC 14496-4 Second edition 2004-12-15 AMENDMENT 14 2007-12-01 Made in Switzerland ISO/IEC 2007 All rights reserved. Unless required for installation or otherwise specified, no part of this CD-ROM may be reproduced, stored in a retrieval system or

15、transmitted in any form or by any means without prior permission from ISO. Requests for permission to reproduce this product should be addressed to ISO copyright office Case postale 56 CH-1211 Geneva 20 Switzerland Internet copyrightiso.org Reproduction may be subject to royalty payments or a licens

16、ing agreement. Violators may be prosecuted. INTERNATIONAL STANDARD Disk 2 of 2 Reference number ISO/IEC 14496-4:2004/ Amd.14:2007(E) ICS 35.040 ISO/IEC 14496-4 Second edition 2004-12-15 AMENDMENT 14 2007-12-01 Made in Switzerland ISO/IEC 2007 All rights reserved. Unless required for installation or

17、otherwise specified, no part of this CD-ROM may be reproduced, stored in a retrieval system or transmitted in any form or by any means without prior permission from ISO. Requests for permission to reproduce this product should be addressed to ISO copyright office Case postale 56 CH-1211 Geneva 20 Sw

18、itzerland Internet copyrightiso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted. ISO/IEC 14496-4:2004/Amd.14:2007(E) ICS 35.040 ISO/IEC 2007 All rights reserved Copyright NoticeThis Amendment to the International Standard contains information

19、 copyright protected by the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). Except as permitted under the laws of Canada, no extract of this Amendment to the International Standard may be reproduced, stored in any retrieval system, or tra

20、nsmitted in any form or by any means, electronic, photocopying, recording, or otherwise, without prior permission from the Standards Council of Canada (SCC). Requests for permission to reproduce this Amendment to the International Standard or parts thereof should be addressed to Manager, Technical D

21、ocument Centre Standards Council of Canada 270 Albert Street, Suite 200 Ottawa, Ontario K1P 6N7 The Canadian adoption of this Amendment to the International Standard contains information copyright protected by the Canadian Standards Association. All rights reserved. No part of this adopted Amendment

22、 may be reproduced in any form whatsoever without the prior permission of the publisher. ISO/IECmaterial is reprinted with permission. Requests for permission to reproduce this adopted Amendment or parts thereof should be addressed to Director, Information Products Canadian Standards Association 506

23、0 Spectrum Way, Suite 100 Mississauga, Ontario L4W 5N6Copyright violators will be prosecuted to the full extent of the law. PRINTED IN CANADAIMPRIMEAU CANADA100%The Canadian Standards Association (CSA) prints its publications on Rolland Enviro100, which contains 100% recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using biogas energy.