CAN CSA-ISO IEC 7810A-2010 Identification cards - Physical characteristics - AMENDMENT 1 Criteria for cards containing integrated circuits.pdf

1、Identification cards Ph ysical characteristics AMENDMENT1: Criteria for cards containing integrated circuitsAmendment 1:2010 (IDT) toNational Standard of CanadaCAN/CSA-ISO/IEC 7810-04(ISO/IEC 7810:2003, IDT)NOT FOR RESALE.PUBLICATION NON DESTINE LA REVENTE.CSA Standards Update ServiceAmendment 1:201

2、0 toCAN/CSA-ISO/IEC 7810-04December 2010Title:Identification cards Physical character istics AMENDMENT1: Criteria for cards containing integrated circuitsPagination:5 pages (iii preliminary and 2 text)To register for e-mail notification about any updates to this publicationgo to www.ShopCSA.caclick

3、on E-mail Services under MY ACCOUNTclick on CSA Standards Update ServiceThe List ID that you will need to register for updates to this publication is 2420822.If you require assistance, please e-mail techsupportcsa.ca or call 416-747-2233.Visit CSAs policy on privacy at www.csagroup.org/legal to find

4、 out how we protect your personal information.Reference numberISO/IEC 7810:2003/Amd.1:2009(E)ISO/IEC 2009INTERNATIONAL STANDARD ISO/IEC7810Third edition2003-11-01AMENDMENT 12009-12-15Identification cards Physical characteristics AMENDMENT 1: Criteria for cards containing integrated circuits Cartes d

5、identification Caractristiques physiques AMENDEMENT 1: the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretar

6、iat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writ

7、ing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org ii ISO/IEC 2009 All rights reservedAmendment 1:2010 to CAN/CSA-ISO

8、/IEC 7810-04ISO/IEC 7810:2003/Amd.1:2009(E) ISO/IEC 2009 All rights reserved iiiForeword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO

9、 or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations

10、, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directi

11、ves, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the n

12、ational bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Amendment 1 to ISO/IEC 7810:2003 was prepared by Joint Technic

13、al Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. It reflects a transfer of certain physical requirements from integrated circuit card standards (primarily ISO/IEC 14443-1). Amendment 1:2010 to CAN/CSA-ISO/IEC 7810-04ISO/IEC 7810:2003/Amd.1:20

14、09(E) ISO/IEC 2009 All rights reserved 1Identification cards Physical characteristics AMENDMENT 1: Criteria for cards containing integrated circuits Page v, Introduction Add the following after list item 6: “7. Criteria for cards containing certain types of integrated circuit have been added.” Page

15、1, Clause 3 Add the following to the list of normative references: ISO/IEC 10373-3, Identification cards Test methods Part 3: Integrated circuit cards with contacts and related interface devices ISO/IEC 10373-6, Identification cards Test methods Part 6: Proximity cards ISO/IEC 10373-7, Identificatio

16、n cards Test methods Part 7: Vicinity cards Page 6 Add the following new clause after 8.14: 9 Criteria for cards containing integrated circuits The following characteristics only apply to cards containing integrated circuits (ICs). 9.1 X-rays The card shall continue to operate as intended after expo

17、sure of any card surface to medium-energy X-radiation as described in the test methods in ISO/IEC 10373-1, with energy in the range of 70 keV to 140 keV, of a cumulative dose of 0,1 Gy per year. NOTE This corresponds to approximately twice the maximum acceptable dose to which humans may be exposed a

18、nnually. 9.2 Dynamic bending stress When subjected to a total of 1 000 bending cycles, the card shall remain testably functional and shall not show any cracked part after testing the card in accordance with the test methods described in ISO/IEC 10373-1. 9.3 Dynamic torsional stress When subjected to

19、 a total of 1 000 torsion cycles, the card shall remain testably functional and shall not show any cracked part after testing in accordance with the test methods described in ISO/IEC 10373-1. Amendment 1:2010 to CAN/CSA-ISO/IEC 7810-04ISO/IEC 7810:2003/Amd.1:2009(E) 2 ISO/IEC 2009 All rights reserve

20、d9.4 Static electricity 9.4.1 Contact IC cards The card shall not be damaged in normal use by a person charged with static electricity. The performance of the card shall not be degraded by exposure to a static discharge in accordance with the test methods described in ISO/IEC 10373-3 between any con

21、tact and ground of a voltage of 2 kV through a resistance of 1 500 ohm from a capacitor of 100 pF. 9.4.2 Contactless IC cards The card shall continue to operate as intended after testing in accordance with the static electricity test methods described in ISO/IEC 10373-6 and ISO/IEC 10373-7 with a te

22、st voltage of 6 kV. NOTE The referenced test methods will eventually be moved to ISO/IEC 10373-1. 9.5 Operating temperature The card shall operate as intended over an ambient temperature range of 0 C to 50 C. Amendment 1:2010 to CAN/CSA-ISO/IEC 7810-04ISO/IEC 7810:2003/Amd.1:2009(E) ICS 35.240.15 IS

23、O/IEC 2009 All rights reserved Copyright NoticeThis A mendment to the I nternational Standard co ntains information copyright protected by th e International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). Except as permitted under the laws of Canada,

24、no extract of this Amendment to the International Standard may be reproduced, stored in any retrieval system, or transmitted in any form or by any means, electronic, photocopying, recording, or otherwise, without prior permission from the Standards Council of Canada (SCC). Requests for permission to

25、 reproduce this Amendment to the International Standard or parts thereof should be addressed to Manager, Technical Document Centre Standards Council of Canada 270 Albert Street, Suite 200 Ottawa, Ontario K1P 6N7 The Canadian adoption of this Amendment to the International Standard contains informati

26、on copyright protected by the Canadian Standards Association. All rights reserved. No part of this adopted Amendment may be reproduced in any form whatsoever without the prior permission of the publisher. ISO/IEC material is reprinted with permission. Requests for permission to reproduce this adopte

27、d Amendment or parts thereof should be addressed to Manager, Sales Canadian Standards Association 5060 Spectrum Way, Suite 100 Mississauga, Ontario L4W 5N6Copyright violators will be prosecuted to the full extent of the law.PRINTED IN CANADAIMPRIMEAU CANADA100%The Canadian Standards Association (CSA) prints its publications on Rolland Enviro100, which contains 100%recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using biogas energy.