CAN CSA-ISO IEC 7810B-2013 Identification cards - Physical characteristics AMENDMENT 2 Opacity.pdf

1、Identification cards Ph ysical characteristics AMENDMENT 2: OpacityAmendment 2:2013 (IDT) toNational Standard of CanadaCAN/CSA-ISO/IEC 7810-04(ISO/IEC 7810:2003, IDT)NOT FOR RESALE. / PUBLICATION NON DESTINE LA REVENTE.Standards Update ServiceAmendment 2:2013 toCAN/CSA-ISO/IEC 7810-04January 2013Tit

2、le:Identification cards Physical characteristics AMENDMENT 2: OpacityPagination:4 pages (iii preliminary and 1 text)To register for e-mail notification about any updates to this publicationgo to shop.csa.caclick on CSA Update ServiceThe List ID that you will need to register for updates to this publ

3、ication is 2422267.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at csagroup.org/legal to find out how we protect your personal information.Reference numberISO/IEC 7810:2003/Amd.2:2012(E)ISO/IEC 2012INTERNATIONAL STANDARD ISO

4、/IEC7810Third edition2003-11-01AMENDMENT 22012-01-15Identification cards Physical characteristics AMENDMENT 2: Opacity Cartes didentification Caractristiques physiques AMENDEMENT 2: Opacit ISO/IEC 7810:2003/Amd.2:2012(E) COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2012 All rights reserved. Unless otherwise

5、 specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright off

6、ice Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org ii ISO/IEC 2012 All rights reservedAmendment 2:2013 to CAN/CSA-ISO/IEC 7810-04ISO/IEC 7810:2003/Amd.2:2012(E) ISO/IEC 2012 All rights reserved iiiForeword ISO (the International

7、 Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by t

8、he respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of i

9、nformation technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft Intern

10、ational Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document

11、 may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. Amendment 2 to ISO/IEC 7810 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identification. It update

12、s opacity requirements by providing criteria to match a new test method that is published in ISO/IEC 10373-1. Amendment 2:2013 to CAN/CSA-ISO/IEC 7810-04Amendment 2:2013 to CAN/CSA-ISO/IEC 7810-04ISO/IEC 7810:2003/Amd.2:2012(E) ISO/IEC 2012 All rights reserved 1Identification cards Physical characte

13、ristics AMENDMENT 2: Opacity Page v, Introduction Add the following after the last numbered point: The test method and criteria for opacity has changed. Previously the test method used a spectrophotometer and criteria included both visible and IR light. The present method uses 2 frequencies of only

14、IR light and a reference material to establish compliance. Page 2 Add the following to the end of Clause 4: 4.12 opacity reference reference card designated ORM 7810 used to establish opacity compliance NOTE Opacity reference cards can be ordered from Eclipse Laboratories, 7732 W. 78th Street, Bloom

15、ington, MN 55439, USA until at least 2013. Page 5 Replace the first paragraph in subclause 8.10 with the following text and equation: All machine readable cards shall have the ability to block infrared wavelength light through the card to the extent as shown in the equations below. The current throu

16、gh the test sensor shall be less when the card is positioned between the source and sensor (Icard) than when the opacity reference is positioned between the source and sensor (Iref). See ISO/IEC 10373-1 for compliance test procedures. Icard at 860 nmIref at 860 nmIcard at 950 nmIref at 950 nm 1 1 AN

17、D Page 5 Delete Note 2 and Note 4 and change Note 3 to become Note 2. Amendment 2:2013 to CAN/CSA-ISO/IEC 7810-04ISO/IEC 7810:2003/Amd.2:2012(E) ICS 35.240.15 ISO/IEC 2012 All rights reserved Copyright NoticeThis Amendment to the International Standard contains information copyright protected by t h

18、e International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC). Except as permitted under the laws of Canada, no extract of this Amendment to the International Standard may be reproduced, stored in any retrieval system, or transmitted in any form or by

19、 any means, electronic, photocopying, recording, or otherwise, without prior permission from the Standards Council of Canada (SCC). Requests for permission to reproduce this Amendment to the International Standard or parts thereof should be addressed to Manager, Technical Document Centre Standards C

20、ouncil of Canada 270 Albert Street, Suite 200 Ottawa, Ontario K1P 6N7 The Canadian adoption of this Amendment to the International Standard contains information copyright protected by CSA Group. All rights reserved. No part of this adopted Amendment may be reproduced in any form whatsoever without t

21、he prior permission of the publisher. ISO/IEC material is reprinted with permission. Requests for permission to reproduce this adopted Amendment or parts thereof should be addressed to Manager, Sales CSA Group 5060 Spectrum Way, Suite 100 Mississauga, Ontario L4W 5N6Copyright violators will be prosecuted to the full extent of the law.PRINTED IN CANADAIMPRIMEAU CANADA100%CSA Group prints its publications on Rolland Enviro100, which contains 100%recycled post-consumer fibre, is EcoLogo and Processed Chlorine Free certified, and was manufactured using biogas energy.