CEN ISO TS 16181-2011 Footwear - Critical substances potentially present in footwear and footwear components - Determination of phthalates in footwear materials (ISO TS 16181 2011).pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationDD CEN ISO/TS 16181:2011Footwear Critical substancespotentially present in footwearand footwear components Determination of phthalatesin footwear materials (ISO/TS16181:2011)Copy

2、right European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN ISO/TS 16181:2011 BRITISH STANDARDNational forewordThis Draft for Development is the UK implementation of CEN ISO/TS 16181:2011

3、.This publication is not to be regarded as a British Standard.It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and experience of its practical application can be obtained.Comment

4、s arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an international standard. A review of this publication will be initiated not later than 3 years after its publication by the i

5、nternational organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards.According to the replies received by the end of the review period, the responsible BSI Committee will d

6、ecide whether to support theconversion into an international Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British Standards House, 389 Chiswick High Road, London W4 4AL.The UK par

7、ticipation in its preparation was entrusted to Technical Committee TCI/69, Footwear, leather and coated fabrics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. U

8、sers are responsible for its correct application. BSI 2011 ISBN 978 0 580 74887 5 ICS 61.060 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2011.Amend

9、ments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION

10、CEN ISO/TS 16181 July 2011 ICS 61.060 English Version Footwear - Critical substances potentially present in footwear and footwear components - Determination of phthalates in footwear materials (ISO/TS 16181:2011) Chaussures - Substances critiques potentiellement prsentes dans les chaussures et les c

11、omposants des chaussures - Dtermination des phtalates dans les matriaux des chaussures (ISO/TS 16181:2011) Schuhe - Mglicherweise in Schuhen und Schuhbestandteilen vorhandene kritische Substanzen - Bestimmung von Phthalaten in Schuhwerkstoffen (ISO/TS 16181:2011) This Technical Specification (CEN/TS

12、) was approved by CEN on 21 May 2011 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European

13、 Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final

14、decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour

15、g, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights o

16、f exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN ISO/TS 16181:2011: ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN I

17、SO/TS 16181:2011CEN ISO/TS 16181:2011 (E) 3 Foreword This document (CEN ISO/TS 16181:2011) has been prepared by Technical Committee CEN/TC 309 “Footwear“, the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 216 “Footwear“. Attention is drawn to the possibility

18、 that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are boun

19、d to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa

20、in, Sweden, Switzerland and the United Kingdom. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN ISO/TS 16181:2011ISO/TS 16181:2011(E) ISO 2011 All rights reserved iiiForew

21、ord ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a techni

22、cal committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of e

23、lectrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to

24、the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. In other circumstances, particularly when there is an urgent market requirement for such documents, a technical committee may decide to publish other types o

25、f document: an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in an ISO working group and is accepted for publication if it is approved by more than 50 % of the members of the parent committee casting a vote; an ISO Technical Specification (ISO/TS) r

26、epresents an agreement between the members of a technical committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting a vote. An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a further three years, r

27、evised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an International Standard or be withdrawn. Attention is drawn to the possibility that some of the elemen

28、ts of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TS 16181 was prepared by the European Committee for Standardization (CEN) Technical Committee CEN/TC 309, Footwear, in collaboration with Technical Committee

29、ISO/TC 216, Footwear, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN ISO

30、/TS 16181:2011ISO/TS 16181:2011(E) iv ISO 2011 All rights reservedIntroduction Phthalates are commonly used as plasticizers in polymers. Toxicological concern has arisen due to their potential effect as endocrine disruptors and some of the listed phthalates are toxic in reproduction. The level of me

31、dia publicity will ensure that their use continues to be of concern to consumers. Phthalates are controversial because high doses of many phthalates have shown hormonal activity in rodent studies. Studies on rodents involving large amounts of phthalates have shown damage to the liver, the kidneys, t

32、he lungs, and the developing testes. This Technical Specification calls for the use of substances and/or procedures that can be injurious to health if appropriate precautions are not observed. It refers only to technical suitability and does not absolve the user from legal obligations relating to he

33、alth and safety at any stage. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN ISO/TS 16181:2011TECHNICAL SPECIFICATION ISO/TS 16181:2011(E) ISO 2011 All rights reserved 1F

34、ootwear Critical substances potentially present in footwear and footwear components Determination of phthalates in footwear materials SAFETY PRECAUTIONS Persons using this Technical Specification should be familiar with normal laboratory practice. This Technical Specification does not claim to addre

35、ss all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions. IMPORTANT It is absolutely essential that tests conducted according to this Tech

36、nical Specification be carried out by suitably trained staff. 1 Scope This Technical Specification specifies a test method to determine the presence of phthalate compounds. This test method is applicable to all types of footwear materials. NOTE 1 This test method can also be used to determine plasti

37、cizers other than those listed in 3.2, subject to validation. NOTE 2 ISO/TR 16178 defines which materials are concerned by this determination. 2 Principle The aim of the method is to extract phthalates in footwear materials such as leather, textile, polymer, coated materials or others. This method u

38、ses extraction apparatus with n-hexane/acetone as solvent. The total n-hexane/acetone extractable phthalate plasticizer content is calculated by weight with gas chromatography-mass spectrometry (GC-MS) detection to identify and quantify individual phthalates. 3 Apparatus and reagents 3.1 Apparatus 3

39、.1.1 Scales, resolution of 1 mg. 3.1.2 Flask, 50 ml. 3.1.3 Water-cooled condenser. 3.1.4 Spark-proof heating mantle/water bath. 3.1.5 Ultrasonic bath. 3.1.6 Microwave extractor. 3.1.7 Steam bath or rotary evaporator. Copyright European Committee for Standardization Provided by IHS under license with

40、 CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN ISO/TS 16181:2011ISO/TS 16181:2011(E) 2 ISO 2011 All rights reserved3.1.8 Calibrated volumetric flasks of suitable volume. Avoid direct contact between the samples and glassware and/or equipment used in ord

41、er to minimize cross-contamination. Glassware, after washing, should be given an extra rinse with 0,1 N nitric acid and finally with acetone, acetone/methanol and/or cyclohexane. Dry at 110 C for 1 h. WARNING The vapour of the organic solvents are highly flammable, especially at high temperature. Al

42、low glassware to cool down before use. 3.1.9 Gas chromatograph with mass-selective detector (GC-MS). 3.2 Reagents Unless otherwise specified, use only reagents of recognized analytical grade. 3.2.1 Water, distilled or of equivalent purity. 3.2.2 n-Hexane, CAS1)number: 110-54-3. 3.2.3 Di-iso-nonyl ph

43、thalate (DINP), CAS number: 28553-12-0 or 68515-48-0. 3.2.4 Di-(2-ethylhexyl) phthalate (DEHP), CAS number: 117-81-7. 3.2.5 Di-n-octyl phthalate (DNOP), CAS number: 117-84-0. 3.2.6 Di-iso-decyl phthalate (DIDP), CAS number: 26761-40-0 or 68515-49-1. 3.2.7 Butyl benzyl phthalate (BBP), CAS number: 85

44、-68-7. 3.2.8 Di-butyl phthalate (DBP), CAS number: 84-74-2. 3.2.9 Di-cyclohexyl phthalate (DCHP), CAS number: 84-61 -7, internal standard. 3.2.10 Acetone, CAS number: 67-64-1. 3.2.11 Mixture of n-hexane/acetone, 80 %/20 % volume fraction. 3.2.12 Di-isobutyl phthalate (DIBP), CAS number: 84-69-5. 4 S

45、ampling The test piece consists of a single material taken from the footwear, such as leather, textile, polymer, coated material or others. The preparation of the sample should involve removal of the individual materials from the footwear, and preparation of a test piece made of particles as small a

46、s possible (but of at least 4 mm). NOTE It is possible to grind the sample. 1) CAS: Chemical Abstract Service. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DD CEN ISO/TS 16181

47、:2011ISO/TS 16181:2011(E) ISO 2011 All rights reserved 35 Test procedure 5.1 Preparation of solutions 5.1.1 Preparation of the internal standard solution Prepare a 500 g/ml stock solution of the internal standard in n-hexane. 5.1.2 Standard solution Prepare a series of individual stock standard solu

48、tions of the individual phthalate in n-hexane, as shown in Table 1. Table 1 Stock solutions Phthalate DIDP DINP DBP BBP DNOP DEHP DIBP Concentration, g/ml 1 000 1 000 200 200 200 200 200 From the stock standard solutions, prepare appropriate phthalate calibration solutions in n-hexane. Use at least

49、five appropriate dilutions of the calibration sets to create calibration graphs, add to each an appropriate amount of internal standard and perform GC-MS analysis. NOTE DIDP and DINP overlap in the chromatogram; the target ions to be chosen are indicated in Annex A. 5.2 Extraction procedures 5.2.1 General Prepa