CEN TS 1329-2-2018 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part.pdf

1、BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U)Part 2: Guidance for the assessment of conformityPD CEN/TS 13292:

2、2018TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 1329-2 June 2018 ICS 23.040.01; 91.140.80 Supersedes CEN/TS 1329-2:2012English Version Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly

3、(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity Systmes de canalisations en plastique pour lvacuation des eaux-vannes et des eaux uses ( basse et haute temprature) lintrieur de la structure des btiments - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 2: Guide po

4、ur lvaluation de la conformit Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approve

5、d by CEN on 24 December 2017 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standar

6、d. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision

7、 about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Ital

8、y, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Cent

9、re: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 1329-2:2018 ENational forewordThis Published Document is the UK implementation of CEN/TS 13292:2018. It supersedes PD CEN/TS 13292:2

10、012, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for nonpressure applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include a

11、ll the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2018 Published by BSI Standards Limited 2018ISBN 978 0 580 98699 4ICS 91.140.80; 83.140.30; 23.040.01Compliance with a British Standard cannot confer immunity from legal ob

12、ligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 30 June 2018.Amendments/corrigenda issued since publicationDate Text affectedPUBLISHED DOCUMENTPD CEN/TS 13292:2018TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIK

13、ATION CEN/TS 1329-2 June 2018 ICS 23.040.01; 91.140.80 Supersedes CEN/TS 1329-2:2012English Version Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conf

14、ormity Systmes de canalisations en plastique pour lvacuation des eaux-vannes et des eaux uses ( basse et haute temprature) lintrieur de la structure des btiments - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 2: Guide pour lvaluation de la conformit Kunststoff-Rohrleitungssysteme zum Ablei

15、ten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebudestruktur - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN on 24 December 2017 for provisional application. The period o

16、f validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS i

17、n the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CE

18、N members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

19、Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels 2018 CEN All rights of explo

20、itation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 1329-2:2018 EPD CEN/TS 13292:2018CEN/TS 1329-2:2018 (E) 2 Contents Page European foreword 3 Introduction . 4 1 Scope . 6 2 Normative references . 6 3 Terms and definitions 6 4 Abbreviated terms 10 5 Gen

21、eral 10 6 Testing and inspection 10 6.1 Material specification 10 6.2 Grouping . 11 6.2.1 General 11 6.2.2 Size groups . 11 6.2.3 Fitting groups . 12 6.3 Type testing . 12 6.4 Batch release tests 15 6.5 Process verification tests . 17 6.6 Audit tests 18 6.7 Indirect tests . 21 6.8 Test records 21 An

22、nex A (informative) Basic test matrix 22 Bibliography 23 PD CEN/TS 13292:2018CEN/TS 1329-2:2018 (E) 3 European foreword This document (CEN/TS 1329-2:2018) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Atten

23、tion is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 1329-2:2012. Compared to the previous version, this document has been upda

24、ted according to the latest version of EN 1329-1. EN 1329 consists of the following parts, under the general title “Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Unplasticized poly(vinyl chloride) (PVC-U)“: Part 1: Specifications for pi

25、pes, fittings and the system Part 2: Guidance for the assessment of conformity (the present document) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cro

26、atia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Tur

27、key and the United Kingdom. PD CEN/TS 13292:2018CEN/TS 1329-2:2018 (E) 4 Introduction Figures 1 and 2 are intended to provide general information on the concept of testing and organization of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type test (TT)

28、, batch release test (BRT), process verification test (PVT) and audit test (AT), this part of EN 1329 details the applicable characteristics to be assessed and the frequency and sampling of testing. A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valve

29、s or assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a manufacturer A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or assemblies by manufacturers, including certification, is given i

30、n Figure 2. PD CEN/TS 13292:2018CEN/TS 1329-2:2018 (E) 5 Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including certification PD CEN/TS 13292:2018CEN/TS 1329-2:2018 (E) 6 1 Scope This document gives guidance for the assessment of conformity of materials (formulations),

31、 products and assemblies in accordance with EN 1329-1 intended to be included in the manufacturers quality plan as part of the quality management system and for the establishment of certification procedures. NOTE 1 It is advised that the quality management system conforms to or is no less stringent

32、than the relevant requirements to EN ISO 9001 2. NOTE 2 If certification is involved, it is advised that the certification body is preferably compliant with EN ISO/IEC 17065 6 or EN ISO/IEC 17021-1 4, as applicable. NOTE 3 In order to help the reader, a basic test matrix is given in Annex A. In conj

33、unction with EN 1329-1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for the following purposes: for soil and waste discharge systems (low and high temperature) inside buildings (application area code “B“); for soil and waste di

34、scharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code “BD“). NOTE 4 This is reflected in the marking of products by “B“ or “BD“. 2 Normative references The following documents are referred to in the text in such

35、 a way that some of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1329-1:2014+A1:2018, Plastics piping systems for soil and wa

36、ste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the systems 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1329-1 and the following a

37、pply. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp 3.1 certification body impartial body, governmental or non-government

38、al, possessing the necessary competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certification body is preferably compliant with EN ISO/IEC 17065 6. PD CEN/TS 13292:2018CEN/TS 1329-2:2018 (E) 7 3.2 inspection

39、body body, that performs inspection Note 1 to entry: An inspection body can be an organization or part of an organization. SOURCE: EN ISO/IEC 17020:2012 3, definition 3.5 Note 2 to entry: An inspection body is preferably compliant with EN ISO/IEC 17020 3. 3.3 testing laboratory laboratory which meas

40、ures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products Note 1 to entry: In the context of this part of EN 1329, the materials and products can be subjected to type testing, batch release testing, process verification testing, audit testing an

41、d witness testing, as applicable. Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 5. 3.4 quality management system part of a management system with regard to quality SOURCE: EN ISO 9000:2015 1, definition 3.5.4 Note 1 to entry: Requirements for quality management

42、systems are given in EN ISO 9001 2. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing performed to prove that the material, product, joint or assembly is capable

43、 of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are done regularly. 3.7 batch release test BRT test performed by or on beh

44、alf of the manufacturer on a batch of materials or products, which needs to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by, or on behalf of the manufacturer on materials, products or joints or assemblies at specific intervals to confi

45、rm that the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of materials or products; rather they are carried out as a measure of process control. PD CEN/TS 13292:20

46、18CEN/TS 1329-2:2018 (E) 8 3.9 audit test AT test performed by a test laboratory on behalf of an inspection body or certification body to confirm that the material, product, joint or assembly continues to conform to the requirements given in the relevant standard and to provide information to assess

47、 the effectiveness of the quality management system 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characteristic, having previously verified its correlation with the specified test 3.11 witness test WT test accepted b

48、y an inspection or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or certification body, qualified in testing 3.12 material generic term for formulations grouped by families, ex

49、pressed by generic names, e.g. polypropylene, stainless steel, brass or EPDM Note 1 to entry: Definition from the work done on harmonization of Drinking water in European Commission, Sub-group on Product Testing Procedures. 3.13 formulation clearly defined homogenous mixture of base polymer with additives, i.e. anti-oxidants, pigments, stabilizers and others, at a dosage level necessary for the processing and the intended use of the final product Note 1 to entry: the term “compound“