CEN TS 13476-4-2013 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U) polypr.pdf

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationPlastics piping systems for non-pressure undergrounddrainage and sewerage Structured-wall piping systems of unplasticizedpoly(vinyl chloride) (PVC-U),polypropylene (PP) and polye

2、thylene (PE)Part 4: Guidance for the assessment of conformityPD CEN/TS 13476-4:2013National forewordThis Published Document is the UK implementation of CEN/TS 13476-4:2013.It supersedes DD CEN/TS 13476-4:2008 which is withdrawn.The UK participation in its preparation was entrusted by Technical Commi

3、tteePRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plastics piping fornon-pressure applications.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of acontract. Users a

4、re responsible for its correct application. The British Standards Institution 2013Published by BSI Standards Limited 2013ISBN 978 0 580 77216 0ICS 23.040.20; 93.030Compliance with a British Standard cannot confer immunity fromlegal obligations.This Published Document was published under the authorit

5、y of theStandards Policy and Strategy Committee on 31 May 2013.Amendments issued since publicationAmd. No. Date Text affectedPUBLISHED DOCUMENTPD CEN/TS 13476-4:2013TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 13476-4 April 2013 ICS 93.030 Supersedes CEN/TS 13476-4:

6、2008English Version Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 4: Guidance for the assessment of conformity Systmes de canalisations en plas

7、tique pour les branchements et les collecteurs dassainissement sans pression enterrs - Systmes de canalisations parois structures en poly(chlorure de vinyle) non plastifi (PVC-U), polypropylne (PP) et polythylne (PE) - Partie 4: Guide pour lvaluation de la conformit Kunststoff-Rohrleitungssysteme fr

8、 erdverlegte drucklose Abwasserkanle und -leitungen - Rohrleitungssysteme mit profilierter Wandung aus weichmacherfreiem Polyvinylchlorid (PVC-U), Polypropylen (PP) und Polyethylen (PE) - Teil 4: Empfehlungen fr die Beurteilung der Konformitt This Technical Specification (CEN/TS) was approved by CEN

9、 on 10 June 2012 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN membe

10、rs are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the p

11、ossible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, L

12、ithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Bru

13、ssels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 13476-4:2013: EPD CEN/TS 13476-4:2013CEN/TS 13476-4:2013 (E) 2 Contents Page Foreword . 3 Introduction 4 1 Scope 5 2 Normative references . 5 3 Terms and definitions 5

14、4 Abbreviated terms 8 5 General . 9 6 Testing and inspection 9 6.1 Material specification PVC . 9 6.2 Material specifications PP . 10 6.3 Material specifications PE . 10 6.4 External reprocessable and recycled materials - validation 11 6.5 Grouping . 11 6.5.1 General . 11 6.5.2 Size groups. 11 6.5.3

15、 Fitting groups . 11 6.6 Type testing 12 6.7 Batch release tests . 16 6.8 Process verification tests 18 6.9 Audit tests 19 6.10 Indirect tests . 21 6.11 Test records . 21 Annex A (informative) Survey of test regime . 22 Bibliography 23 PD CEN/TS 13476-4:2013CEN/TS 13476-4:2013 (E) 3 Foreword This do

16、cument (CEN/TS 13476-4:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CE

17、NELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 13476-4:2008. The main changes with respect to the previous edition are listed below: updating of the references in Clause 2 and Bibliography; updating of the definitions in Clause 3; S

18、pecification of PVC reprocessable and recycling material Table 2; deletion of Table 3, Compound specification PP masterbatch; deletion of Table 5, Compound specification PE masterbatch; changing Table 8, by deletion of column “P“; deletion of 4.2.3.2, Preliminary type testing; deletion of 4.2.3.3, I

19、nitial type testing; deletion of Table 11, Specification of use of reprocessable and recyclable material that shall require the production to be considered at least as one batch; deletion of Table 12, Material characteristics that require BRT. EN 13476 consists of the following Parts under the gener

20、al title Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): Part 1: General requirements and performance characteristics; Part 2: Specifications for pipes a

21、nd fittings with smooth internal and external surface and the system, Type A; Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the system, Type B; Part 4: Guidance for the assessment of conformity (this Technical Specification). According to the CE

22、N-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,

23、Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 13476-4:2013CEN/TS 13476-4:2013 (E) 4 Introduction Figures 1 and 2 are intended to provide

24、general information on the concept of testing and organisation of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type testing (TT), batch release test (BRT), process verification test (PVT), and audit test (AT), this part of EN 13476 details the applica

25、ble characteristics to be assessed as well as the frequency and sampling of testing. A typical scheme for the assessment of conformity of compounds/formulations, pipes, fittings, joints or assemblies by manufacturers is given in Figure 1. Figure 1 Typical scheme for the assessment of conformity by a

26、 manufacturer A typical scheme for the assessment of conformity of compounds/formulations, pipes, fittings, joints or assemblies by manufacturers, including a third-party certification, is given in Figure 2. Figure 2 Typical scheme for the assessment of conformity by a manufacturer, including a thir

27、d-party certification PD CEN/TS 13476-4:2013CEN/TS 13476-4:2013 (E) 5 1 Scope This Technical Specification gives guidance for the assessment of conformity of compounds / formulations, products and assemblies in accordance with the applicable part(s) of EN 13476-1, EN 13476-2 and EN 13476-3 intended

28、to be included in the manufacturers quality plan as part of the quality management system and for the establishment of third-party certification procedures. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001:2008 1.

29、If third-party certification is involved, it is recommended that the certification body is accredited to EN 45011 2, EN 45012 3 or EN ISO/IEC 17021 4, as applicable. In conjunction with EN 13476-1, EN 13476-2 and EN 13476-3 (see Foreword) this document is applicable to Plastics piping systems for no

30、n-pressure underground drainage and sewerage Structural-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE): for non-pressure underground drainage and sewerage outside the building structure (application area code “U”) reflected in de-marking o

31、f products by “U”, and for non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code “D” and outside the building structure (application area code “U”) reflected in de marking of products by “UD”. 2 Normative references The followin

32、g documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13476-1:2007, Pl

33、astics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: General requirements and performance characteristics EN 13476-2:2007, Plastics piping systems for no

34、n-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for pipes and fittings with smooth internal and external surface and the system, Type A EN 13476-3:2007+A1:2009,

35、Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 3: Specifications for pipes and fittings with smooth internal and profiled external surface and the s

36、ystem, Type B 3 Terms and definitions For the purposes of this document, the following terms and definitions given in EN 13476-1:2007, EN 13476-2:2007 and EN 13476-3:2007+A1:2009 and the following apply. 3.1 certification body impartial body, governmental or non-governmental, possessing the necessar

37、y competence and responsibility to carry out certification of conformity according to given rules of procedure and management Note 1 to entry: A certification body is preferably accredited to EN 45011 2. PD CEN/TS 13476-4:2013CEN/TS 13476-4:2013 (E) 6 3.2 inspection body impartial organisation or co

38、mpany, approved by the certification body as possessing the necessary competence to verify and/or to carry out initial type testing, audit testing and inspection of the manufacturers factory production control in accordance with the relevant standard Note 1 to entry: An inspection body is preferably

39、 accredited to EN ISO/IEC 17020 5. 3.3 testing laboratory laboratory which measures, tests, calibrates or otherwise determines the characteristics of the performance of materials and products Note 1 to entry: In the context of this part of EN 13476, the materials and products can be subjected to typ

40、e testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable. Note 2 to entry: A testing laboratory is preferably accredited to EN ISO/IEC 17025 6. 3.4 quality management system management system to direct and control an organization with regard t

41、o quality Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001:2008 1. 3.5 quality plan document setting out the specific quality practices, resources and sequence of activities relevant to a particular product or range of products 3.6 type testing TT testing perform

42、ed to prove that the material, product, joint or assembly is capable of conforming to the requirements given in the relevant standard Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly provided that the process verification tests are do

43、ne regularly. 3.7 batch release test BRT test performed by or on behalf of the manufacturer on a batch of formulation/ compound or products, which has to be satisfactorily completed before the batch can be released 3.8 process verification test PVT test performed by or on behalf of the manufacturer

44、on formulation/compound or products, joints or assemblies at specific intervals to confirm that the process continues to be capable of producing products which conform to the requirements given in the relevant standard Note 1 to entry: Such tests are not required to release batches of formulation/co

45、mpound or products and are carried out as a measure of process control. 3.9 audit test AT test performed by a test laboratory on behalf of an inspection body or certification body to confirm that the formulation / compound, product, joint or assembly continues to conform to the requirements given in

46、 the relevant standard and to provide information to assess the effectiveness of the quality management system PD CEN/TS 13476-4:2013CEN/TS 13476-4:2013 (E) 7 3.10 indirect test IT test performed by or on behalf of the manufacturer, different from that specified test for that particular characterist

47、ic, having previously verified its correlation with the specified test 3.11 witness test WT test accepted by an inspection or a certification body for type testing and/or audit testing, which is carried out by or on behalf of the manufacturer and supervised by a representative of the inspection or c

48、ertification body, qualified in testing 3.12 material generic term for compositions compounds/formulations grouped by families, expressed by generic names, e.g. polypropylene, stainless steel, brass or EPDM Note 1 to entry: Definition from European Commission, Directorate-General for Enterprise and

49、Industry, Sub-group on Product Testing Procedures (EC, DG ENT and IND, SG PTP). 3.13 compound / formulation clearly defined homogenous mixture of base polymer with additives, i.e. antioxidants, pigments, stabilizers and others, at a dosage level necessary for the processing and the intended use of the final product Note 1 to entry: Definition from EC, DG ENT and IND, SG PTP (European Commission, Directorate-General for Enterprise and Industry, Sub-group on Product Testing Proc