CEN TS 14578-2013 Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Reco.pdf

1、BSI Standards PublicationPD CEN/TS 14578:2013Plastics piping systems forwater supply or drainageand sewerage Glass-reinforced thermosettingplastics (GRP) based onunsaturated polyester resin(UP) Recommended practicefor installationPD CEN/TS 14578:2013 PUBLISHED DOCUMENTNational forewordThis Published

2、 Document is the UK implementation of CEN/TS 14578:2013. It supersedes DD CEN/TS 14578:2003 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/88/2, Plastics piping for pressure applications.A list of organizations represented on this committee can be

3、 obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 82219 3ICS 23.040.20; 83.140.

4、99Compliance with a British Standard cannot confer immunity from legal obligations.This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 December 2013.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dPD CEN/TS 14578:20

5、13TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 14578 December 2013 ICS 83.140.99; 23.040.20 Supersedes CEN/TS 14578:2003English Version Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsatur

6、ated polyester resin (UP) - Recommended practice for installation Systmes de canalisations plastiques pour ladduction deau et lassainissement - Plastiques thermodurcissables renforcs de verre (PRV) base de rsine de polyester non satur (UP) - Pratique recommande pour la pose Kunststoff-Rohrleitungssy

7、steme fr die Wasserversorgung und Ableitung von Abwasser - Glasfaserverstrkte duroplastische Kunststoffe (GFK) auf der Basis von ungesttigtem Polyesterharz (UP) - Empfehlungen fr die Verlegung This Technical Specification (CEN/TS) was approved by CEN on 10 September 2013 for provisional application.

8、 The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of

9、this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN i

10、s reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor

11、way, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of expl

12、oitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 14578:2013 EPD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 2 Contents Page Foreword 3 Introduction .3 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Procedures .6 4.1 General 6 4.2 Special

13、conditions for pipes having a nominal stiffness less than SN 1250 6 5 Specific information and recommendations .6 5.1 General 6 5.2 Special transportation requirements .6 5.3 Maximum storage heights on site 6 5.4 Maximum storage period in direct sunlight 6 5.5 Climatic conditions requiring special s

14、torage 6 5.6 Limiting deflections .6 5.7 Coefficient of linear expansion 7 5.8 Longitudinal tensile modulus and strength 7 5.9 Appropriate jointing system .7 5.10 Cold bending 7 5.11 Permitted rates of loss of water and/or pressure .7 Bibliography 8 PD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 3 Forewo

15、rd This document (CEN/TS 14578:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of which is held by NEN. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN a

16、nd/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes CEN/TS 14578:2003. The following is a list of the major technical changes that have been made since the previous edition: a) removed reference to ENV 1046 which will be revised to beco

17、me applicable only to thermoplastic pipes; b) reference is made to ISO/TS 10465-1 which is specifically addressing installation of GRP piping; c) revised wording to improve clarity and to reflect revisions to GRP product standards EN 1796 and EN 14364. According to the CEN-CENELEC Internal Regulatio

18、ns, the national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, I

19、taly, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. PD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 4 Introduction System Standards EN 1796 and EN 14364 specify the properties of a piping

20、 system and its components when made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for pressure and non-pressure water or sewerage applications. A System Standard includes specifications for pipes, fittings and joints and makes refer

21、ence to supporting standards covering test methods, recommended practices for installation (this Technical Specification) and procedures for assessment of conformity. Matters such as design procedures, determination of long-term safety factors based on a semi-probabilistic approach, surge allowance

22、and allowable negative pressures for buried GRP pipe applications are covered in CEN/TS 14807 1. This supporting Technical Specification, which covers practices for installation, is intended to be used in conjunction with ISO/TS 10465-1 by, amongst others, end-users, authorities, design engineers, t

23、esting and certification institutes and manufacturers. In this Technical Specification, much of the guidance is expressed as requirements, e.g. by use of “shall” or by instructions in the imperative. It is strongly recommended that these be followed whenever applicable. Other guidance is presented f

24、or consideration as a matter of judgement in each case, e.g. by use of “should”. PD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 5 1 Scope This Technical Specification (CEN/TS) specifies recommended practices for the underground installation of piping systems made of glass-reinforced thermosetting plastic

25、s based on unsaturated polyester resin (GRP-UP), intended to be used for pressure or non-pressure water or sewerage applications and complying with, as applicable, EN 14364 and/or EN 1796. It is applicable to GRP-UP piping systems of nominal sizes from DN 100 to DN 4000 which are intended to be used

26、 for the conveyance of liquids at temperatures up to 50 C and at pressures of 0,5 bar and greater. Design procedures, the determination of long-term safety factors based on a semi-probabilistic approach, surge allowance and allowable negative pressures for buried GRP pipe applications are addressed

27、in CEN/TS 14807 1. Piping systems conforming to EN 1796 or EN 14364 can also be used for above-ground applications provided the influence of the environment and the supports is considered in the design of the pipes and joints. It is recommended to refer to ISO/TR 10986 4 for guidelines for the insta

28、llation of above-ground flexible jointed pipes. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. 2 Normative

29、references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) appli

30、es. EN 805, Water supply - Requirements for systems and components outside buildings EN 1610, Construction and testing of drains and sewers EN 1796:2013, Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester r

31、esin (UP) EN 14364:2013, Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints ISO/TS 10465-1:2007, Underground installation of flexible glas

32、s-reinforced pipes based on unsaturated polyester resin (GRP-UP) - Part 1: Installation procedures 3 Terms and definitions For the purposes of this document the terms and definitions given in ISO/TS 10465-1:2007 apply. In addition, see also EN 1796:2013 and EN 14364:2013 for general terms and defini

33、tions relating to GRP pipes. PD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 6 4 Procedures 4.1 General Pipes and fittings covered by EN 1796 or EN 14364 shall be installed in accordance with ISO/TS 10465-1 taking into account the following information and guidance. In conditions not covered thereby, the

34、engineer shall make his own recommendations. Attention is drawn to the limitations that may apply to negative pressure in service, in particular if the pipe zone backfill material is removed and to mechanical compaction requirements during installation. This is of particular concern for pipe stiffne

35、ss up to and including SN 5000 (see also ISO/TS 10465-1). 4.2 Special conditions for pipes having a nominal stiffness less than SN 1250 Pipes having a nominal stiffness less than SN 1250 are not intended for laying directly in the ground. When installed in the ground, they shall be encased in concre

36、te. 5 Specific information and recommendations 5.1 General In ISO/TS 10465-1 reference is made to ISO product standards ISO 10639 3 and ISO 10467 2. These ISO product standards are similar to EN 1796 and EN 14364 respectively. For any such reference, substitute the respective EN product standard. 5.

37、2 Special transportation requirements When following the guidance given in ISO/TS 10465-1 particular care shall be taken to avoid impact damage. Pipes and fittings shall be secured before transporting them to or around the site. 5.3 Maximum storage heights on site Guidelines for the number of layers

38、 in a storage stack are given in ISO/TS 10465-1. The manufacturer may also supply specific storage recommendations. 5.4 Maximum storage period in direct sunlight When materials such as ultraviolet inhibitors have been incorporated or other protective pipe constructions have been used, pipes and fitt

39、ings may be stored in direct sunlight for their design lives. Care should be taken to protect rubber-sealing profiles from prolonged exposure to sunlight. Consult the manufacturer for all storage guidelines and recommendations. 5.5 Climatic conditions requiring special storage Apart from high winds,

40、 there are no climatic conditions that require special storage conditions for products conforming to EN 1796 or EN 14364. 5.6 Limiting deflections In no case shall the vertical diameter increase by more than 1,5 % of the mean diameter due to installation procedures, e.g. the relative initial ovaliza

41、tion shall not exceed 1,5 %. This may be verified by measurements when the pipe zone backfilling operation is completed. The initial deflection should be measured and monitored to assist in achieving a satisfactory installation. PD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 7 The property requirements f

42、or GRP-UP pipes made in accordance with EN 1796 and EN 14364 assume that maximum permissible initial deflection is 3 % and the maximum long term deflection is 6 %. If the recommendations for installation in ISO/TS 10465-1 are followed it is expected that the deflections achieved will be less than th

43、ese limiting values. If the maximum long term deflection is different than 6 % the requirements are adjusted proportionally as covered in EN 1796 and EN 14364. 5.7 Coefficient of linear expansion A typical range for the coefficient of linear expansion in the axial direction, , is 20 106/C to 50 106/

44、C. This property varies with the nature, orientation and quantity of reinforcement in any particular pipe. The manufacturer shall provide the relevant information when requested by the purchaser. 5.8 Longitudinal tensile modulus and strength These properties vary with the nature, orientation and qua

45、ntity of reinforcement in any particular pipe. The manufacturer shall provide this information when requested by the purchaser. 5.9 Appropriate jointing system Joints described in and conforming to EN 1796 or EN 14364, as applicable, should be used. 5.10 Cold bending GRP-UP pipes are not suitable fo

46、r cold bending. Changes in direction should be achieved either by using fittings conforming to EN 1796 or EN 14364 or by utilizing the flexibility of the joint. 5.11 Permitted rates of loss of water and/or pressure Guidelines for testing both pressure and non-pressure systems is given in ISO/TS 1046

47、5-1. In addition, attention shall also be given to the requirements given in EN 805 and EN 1610 as may be applicable. PD CEN/TS 14578:2013CEN/TS 14578:2013 (E) 8 Bibliography 1 CEN/TS 14807, Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin

48、(UP) - Guidance for the structural analysis of buried GRP-UP pipelines 2 ISO 10467, Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin 3 ISO 10639, Plastics piping systems for p

49、ressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin 4 ISO/TR 10986, Plastics piping systems for pressure and non-pressure applications - Installation of pipes above ground - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated b