CEPT T L 02-11 E-1987 Interfaces for Operation Maintenance and Supervision of Telecommunications Equipment in Telecommunications Centres《电信中心电信设备操作、维护和监督接口》.pdf

1、Page 1 (old reference: T/TR 02-1 1 E) Recommendation T/L 02-11 (Copenhagen 1987) INTERFACES POR OPERATION, MAINTENANCE AND SUPERVISION OF TELECOMMUNICATIONS EQUIPMENT IN TELECOMMUNICATIONS CENTRES Recommendation proposed by Working Group T/WG 12 “Transmission and multiplexing” (TM) Text of the Recom

2、mendation revised adopted by “Telecommunications” Commission: “The European Conference of Posts and Telecommunications Administrations, considering . - that telecommunications equipment is usually located in Telecommunications Centres, - that the installation of equipment from multiple sources in a

3、single Telecommunications Centre requires a certain degree of standardisation of interfaces for operations, maintenance and supervision, - that the existing Recommendations of CCITT on the subject do not provide a sufficient degree of standardisation, - that the CEPT Administrations are in favour of

4、 any harmonisation measures likely to facilitate maintenance, O operations and supervision, recommends that the members of the CEPT should apply the specifications contained in the present Recommendation concerning the harmonisation of interfaces for operation, maintenance and supervision of telecom

5、munications equipment.” - - Edition of December 15, 1987 f i I I !CEPT T/L*02-33*E 87 = 2326434 0005963 3 T/L 02-11 E Page 2 Contents 1. OBJECTIVES. . 2 2ANs . 2 3. ClINTERFACE. 2 4. C2 INTERFACE. 2 5. C3INTERFACE. 3 1. OBJECTIVES To define interfaces between telecommunications equipments and a data

6、 network designed to realise among others the following functions : - To provide network management information. - To provide network performance information. - To assist in localising intermittent faults. - To allow all information to be made available at remote network management and maintenance c

7、entres. - To permit remote control functions. 2, MEANS In order to attain these objectives it is necessary: - To provide where possible, messages characterising performance of each telecommunications equipment. - To set up a system for acquisition, processing and transmission of fault, measurement o

8、r control More particularly in the case of a Telecommunications Centre, a network structure for operation, main- tenance and supervision on several levels, in accordance with Figure 1 (T/L 02-1 1) is envisaged. The primary role of the central processing equipment is to control the collection device,

9、 to process and store the information received and to present it at operations terminals, if needed. The necessity for central processing equipment depends on economic considerations, the processing power of the collection devices and on the number of collection devices situated at the centre. A col

10、lection device is an equipment which primarily collects and may distribute information/data from and to telecommunications equipment. In practice it may include additional functions which might otherwise be implemented by the central processing equipment. These different levels constitute an area of

11、 possible harmonisation: Interface C1: Interface primarily intended for connection between telecommunications equipments and collection devices. Interface C2: Interface primarily intended for connection between collection devices and the central processing equipments of a Telecommunication Centre. I

12、nterface C3 : Interface between Telecommunications Centre and data transport network. Applications different from the primary applications are not excluded where practical, operational or economic factors dictate. For example a telecommunications equipment may alternatively be provided with a C2 or

13、C3 interface. Certain types of collection device may also be connected to the central processing equipment by a type C1 interface. Any necessary conversion between the C2 interface and the C3 interface may be carried out in the central processing equipment. messages. 3. C1 INTERFACE Under Study. 4.

14、C2 INTERFACE 4.1, Introduction This interface is primarily intended for the connection between collection devices and the central processing equipments of a Telecommunications Centre. Edition of December 15, 1987 4.2. 4.2.1. 4.2.2. 4.2.3. 5. CEPT T/L*02-33*E 7 2326434 00059b2 5 _. _ T/L 02-11 E Page

15、 3 Interface Characteristics Layer 1 : - multipoint connection; - configuration: bus; - electrical characteristics: CCITT Recommendation V. 11/EIA RS485. Data transmission on I or 2 twisted pairs; an additional pair may be required for timing. Maximum speed: 19,200 bit/s. The requirement for higher

16、speeds is under study. Layer 2: - An HDLC synchronous protocol, standard IS0 7809 in an unbalanced mode, standard 3309,4335, done - Standard HDLC Frame with a maximum frame length of 128 bytes. (Under study.) Layer 7: This is the Application Level. Examples of the main functions which might be imple

17、mented are as follows: - Maintenance Functions: by a polling system (master/slave). - transfer of alarm state messages - transfer of fault location data - control of alarm thresholds - transfer of performance data - control of performance calculation algorithms - Operations Functions: - database upg

18、rading - updating of collection device conguration - transfer of software - initiation of protection switching - change of equipment set-up conditions - Performance Functions: - Remote Control Functions: C3 INTERFACE Under study. Edition of December 15, 1987 I r-/; 1 j I . CEPT T/L*OZ-LL*E 87 2326434 0005963 7 I CD * T/L 02-11 E Page 4 I I DATA NETWORK c3 c3 c2 . Telecgmmunicatione Centre CENTRAL PROCESSIN EPUIPMENT -i c1 id CD: Collection Device Eq: Telecommunications Equipment Figure 1 (T/L 02-11). c2 c3 c1 Edition of December 15, 1987