1、 CGSB CAN/CGSB41= 53-95 a* = 1874650 0027333 609 CANICGSB-5 1.53-95 Supersedes 5 1 -GP-53M Canadian General Stan dards Board Poly (Vinyl Chloride) Jacketing Sheet, for Insulated Pipes, Vessels and Round Ducts National Standard of Canada P Copyright Canadian General Standards Board Provided by IHS un
2、der license with CGSBNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- CGSB CAN/CGSB-SL- 53-95 i* H L87465Q 0027334 545 W The CANADIAN GENERAL STANDARDS BOARD (CGSB), under whose auspices this standard has been developed is a government agency within the Federal Dep
3、artment of Supply and Services. CGSB is engaged in the production of voluntary standards in a wide range of subject areas through the media of standards committees and the consensus process. The standards committees are composed of representatives of relevant interests including producers, consumers
4、 and other users, retailers, governments, educational institutions, technical, professional and trade societies, and research and testing organizations. Any given standard is developed on the consensus of views expressed by such representatives. The Ministers Advisory Council on CGSB reviews the res
5、ults of the consensus process. CGSB has been accredited by the Standards Council of Canada as a national standards-writing organization. The standards that it develops and offers as National Standards of Canada conform to the criteria and procedures established for this purpose by the Standards Coun
6、cil of Canada. in addition to standards it publishes as national standards, CGSB produces standards to meet particular needs, in response to requests from a variety of sources in both the public and private sectors. Both CGSB standards and national standards developed by CGSB are developed in confor
7、mance with the policies described in the Policy Manual for the Development and Maintenance of Standards by CGSB. CGSB standards are subject to review and revision at any time, so as to ensure that they keep abreast of technological progress. Suggestions for their improvement, which are always welcom
8、e, should be brought to the notice of the standards committees concerned. Changes to standards are issued either as separate amendment sheets or in new editions of standards. An up-to-date listing of CGSB standards, including details on latest issues and amendments, and ordering instructions, will b
9、e found in the CGSB Catalogue, which is published annually and is available without charge upon request. Although the intended primary application of this standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability
10、 for their particular purpose. Many tests required by CGSB standards are inherently hazardous. CGSB neither assumes nor accepts any responsibility for any injury or damage that may occur during or as the result of tests, wherever performed. CGSB takes no position respecting the validity of any paten
11、t rights asserted with any item connected with this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights are entirely their own responsibility. Further information on CGSB and its services and standards may be obtained from: The Manager
12、Marketing and Sales Services Canadian General Standards Board Ottawa, Canada KIA 1G6 The STANDARDS COUNCIL OF CANADA is the co-ordinating body of the National Standards System, a federation of independent, autonomous organizations working towards the further development and improvement of voluntary
13、standardization in the national interest. The principal objectives of the Council are to foster and promote voluntary standardization as a means of advancing the national economy, benefiting the health, safety and welfare of the public, assisting and protecting the consumer, facilitating domestic an
14、d international trade, and furthering international co-operation in the field of standards. A National Standard of Canada is a standard which has been approved by the Standards Council of Canada and one which reflects a reasonable agreement among the views of a number of capable individuals whose co
15、llective interests provide, to the greatest practicable extent, a balance of representation of producers, users, consumers and others with relevant interests, as may be appropriate to the subject in hand. It normally is a standard that is capable of making a significant and timely contribution to th
16、e national interest. Approval of a standard as a National Standard of Canada indicates that a standard conforms to the criteria and procedures established by the Standards Council of Canada. Approval does not refer to the technical content of the standar4 this remains the continuing responsibility o
17、f the accredited standards-writing organization. Those who have a need to apply standards are encouraged to use National Standards of Canada whenever practicable. These standards are subject to periodic review; therefore, users are cautioned to obtain the latest edition from the organization prepari
18、ng the standard. The responsibility for approving National Standards of Canada rests with the: Standards Council of Canada 45 OConnor Street suite 1200 Ottawa, Ontario K1P 6N7 How to order Publications by Telephone - (613) 941-8703 or - 1-800-665-CGSB (Canada only) I bYF= - (613) 941-8705 by Mail -
19、CGSB Sales Centre Ottawa, Canada K1A lG6 in Person - Suite 1402 222 Queen Street Ottawa. Ontario Copyright Canadian General Standards Board Provided by IHS under license with CGSBNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- CGSB CAN/CGSB-51* 53-95 * M 1874650 0
20、027335 481 M NATIONAL STANDARD OF CANADA CANICGSB-51.53-95 Supersedes 5 1 -GP-53M November 1977 POLY(V1NYL CHLORIDE) JACKETING SHEET, FOR INSULATED PIPES, VESSELS AND ROUND DUCTS Prepared Canadian by the Approved by the General Standards Board -3 Standards Council of Canada Q Published July 1995 by
21、the Canadian General Standards Board Ottawa, Canada KIA 1G6 Minister of Supply and Services Canada - 1995 No part of this publication may be reproduced in any form without the prior permission of the publisher. Copyright Canadian General Standards Board Provided by IHS under license with CGSBNot for
22、 ResaleNo reproduction or networking permitted without license from IHS-,-,- CGSB CAN/CGSB-5L. 53-95 St L874b50 002733b 3L8 CANADIAN GENERAL STANDARDS BOARD COMMITTEE ON INSULATION FOR MECHANICAL SYSTEMS Northcott, J.E. Bauer, F.C. Bazos, D.C. Bell, D. Chanter, A. Clayman, S.I. Crimi, T. Evans, J. H
23、ajdur, W. Holden, J.W. Jolicoeur, C. Laszlo, G. McLaren, K. Piggin, A.S. Robert, M. Roy, B. Scott, B. Skarzenski, J. Storey, B. Tate, A. Waters, R. Watts, R. Webb, H. Wilson, K. (Membership at date of approval) Chairperson Department of National Defence ORTECH Rubatex Corporation Saskatchewan Constr
24、uction Association Poi y fab Knauf Fiber Glass Underwriters Laboratories of Canada Roxul Inc. Gummed Papers Ltd. Partek Insulations Ltd. Childers Products Co. Ltd. Department of Public Works Department of Municipal Affairs, Alberta PML Associates Armstrong Cork Canada Ltd. Department of Transport Th
25、e Sure-Fit System Applied Insulation Co. Ltd. Manson Insulation Inc. Department of TranspodCanadian Coast Guard Canadian Construction Materials Centre Department of Public Works Thermal Insulation Association of Canada Owens-Coming Canada Inc. Craig, W. Secretary Canadian General Standards Board . A
26、cknowledgment is de for the translation of this National Standard of Canada by the Translation Bureau of the Department of the Secretary of State. CANKGSB-51.53-95 - -. - Copyright Canadian General Standards Board Provided by IHS under license with CGSBNot for ResaleNo reproduction or networking per
27、mitted without license from IHS-,-,-CANKGSB-5 153-95 Supersedes 5 1 -GP-53M November 1977 CANADIAN GENERAL STANDARDS BOARD 1. 1.1 1.2 2. 2.1 2.1.1 2.1.2 2.2 3. 3.1 . 3.2 POLY(VINYL CHLORIDE) JACKETING SHEET, FOR INSULATED PIPES, VESSELS AND ROUND DUCTS SCOPE This standard applies to poly(viny1 chlor
28、ide) (PVC) sheet used as jacketing over insulated surfaces of vessels and round ducts, or preformed jacketing for pipe elbows, tees, etc., where the surface temperature is between -20C and +65OC. The testing and evaluation of a product against this standard may require the use of materials and/or eq
29、uipment that could be hazardous. This document does not purport to address all the safety aspects associated with its use. Anyone using this standard has the responsibility to consult the appropriate authorities and to establish appropriate health and safety practices in conjunction with any existin
30、g applicable regulatory requirements prior to its use. APPLICABLE PUBLICATIONS The following publications are applicable to this standard: Underwriters Laboratories of Canada (ULC) CAN/LC-S102.2 - Standard Method of Test for Surface Burning Characteristics of Flooring, Floor Covering and Miscellaneo
31、us Materials and Assemblies. American Society for Testing and Materiais (ASTM) C 665 - Specification for Mineral Fiber Blanket Thermal Insulation for Light Frame Construction and D 543 - Test Method for Resistance of Plastics to Chemical Reagents D 638 - Test Method for Tensile Properties of Plastic
32、s D 648 - Test Method for Deflection Temperature of Plastics Under Flexural Load D 882 - Test Methods for Tensile Properties of Thin Plastic Sheeting D 1637 - Test Method for Tensile Heat Distortion Temperature of Plastic Sheeting D 1784 - Specification for Rigid Poly (Vinyl Chloride) (PVC) Compound
33、s and Chlorinated Poly (Vinyl Chloride) D 1822 - Test Method for Tensile Impact Energy to Break Plastics and Electrical Insulating Materiais E 96 - Test Methods for Water Vapor Transmission of Materials. Manufactured Housing (CPVC) Compounds Reference to the above publications is to be latest issues
34、 unless otherwise specified by the authority applying this standard. The sources of these publications are shown in the Notes section. GENERAL REQUIREMENTS Material - The PVC jacketing shall be manufactured from the polymer of vinyl chloride or the copolymer of vinyl chloride as a principal material
35、. Appearance - The PVC sheet shall not show any signs of bubbles, blisters, streaks, pinholes, and specks of foreign matter. 1 Copyright Canadian General Standards Board Provided by IHS under license with CGSBNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4. 4.1 4
36、.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.1 1 4.12 4.13 4.14 5. 5.1 5.2 6. 6. i 6.1.1 DETAILED REQUIREMENTS Thickness - The thickness of the PVC sheet shall be a minimum of 0.25 mm and a maximum of 0.50 mm. Tensile Strength - When tested in accordance with ASTM D 638 or D 882, the tensile strength of th
37、e PVC sheet shall be 35 MPa minimum in both the transverse and longitudinal directions. Impact Strength - When tested in accordance with ASTM D 1822 the minimum impact strength of the PVC sheet shall be as follows: . Temperature Minimum Impact Strength -20C 400 kJ/m2 0C 600 kJ/m2 +23“C 800 kJ/m2 Hea
38、t Distortion - When the PVC sheet is tested in accordance with ASTM D 1637 (See Appendix A) or D 648, the tensile heat distortion temperature shall be 65OC minimum. Surface Burning Characteristics - When tested in accordance with CANAJLC-S 102.2, the PVC sheet shall have a flame spread classificatio
39、n not greater than 25 and smoke development not greater than 50. Water Vapour Permeance - When tested in accordance with ASTM E 96, Procedure C and calculated as the average of four specimens, the sheet shall have a water vapour permeance of less than 9 ng/Pa.s-m2. FlexibUily - When subjected to the
40、 test described in par. 6.1.1, the PVC sheet shall not crack. Dimensional Stability - When subjected to the test in par. 6.1.2, the PVC sheet shall not shrink more than 1.5% in either direction. Width - The PVC sheet shall be between 700 and 1400 mm wide as specified (par. 7.1). The tolerance on the
41、 width shall be +6 mm and -O mm. Length - The length of PVC sheet shall be as specified (par. 7.1). If the PVC sheet is supplied in rolls, all material in any one roll shall be continuous. The tolerance on length shall be f10 mm. Preformed Shapes - Preformed shapes shall be as specified for the appl
42、ication (par. 7.1). Colour - The PVC sheet shall be a uniform white colour unless otherwise specified (par. 7.1). Chemical Resistance - When tested in accordance with ASTM D 543 or D 1784, the PVC sheet shall be resistant to acids, alkalis, hydrocarbons, alcohols, and mineral and vegetable oils Fung
43、i Resistance - When tested in accordance with ASTM C 665, Section 13.9, the PVC sheet shall not show greater fungi growth than control specimens. PREPARATION FOR DELIVERY Packaging, Packing and Marking - Unless otherwise specified (par. 7.1), packaging, packing and marking shall conform to normal co
44、mmercial practice. Labelling - When specified (par. 7.1), labelling of each package of PVC sheet shall include the Standard number, the product name, and the name of the manufacturer or supplier. INSPECTION Testing FZexibili&y - Cut five strips of material 200 by 25 mm in the machine direction. Cond
45、ition the specimens for at least 24 h at -10C and then bend once through 90“ around a 6 mm diameter mandrel at -10C with a uniform bending rate so the total bend is made in 2 s. Immediately after bending, examine the specimens by normal vision for cracks. 2 CANKGSB-51.53-95 Copyright Canadian Genera
46、l Standards Board Provided by IHS under license with CGSBNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- CGSB CAN/CGSB-5L- 53-75 * m 18746.50 0027337 027 = 6.1.2 SiUinkuge - Cut four specimens of 300 x 300 mm. Before aging, condition the specimens to constant mass
47、 at 23 f 2C and SO f 5% relative humidity (RH). Draw fine reference lines on the specimens 250 mm apart to an accuracy of M.2 mm in both the machine and cross-machine directions. hge the specimens by immersing them in water at room temperature for 3 h, dry at room temperature for 16 h, then oven dry
48、 at 50C for 3 h. Following the aging treatment, condition the specimens to constant mass at 23 f 2C and 50 f 5% RH. Measure the dimensional change on the specimens as follows: Place a flat, smooth-surfaced, evenly distributed mass of 4.5 kg about 250 mm square on the specimen inside the reference li
49、nes and measure the distance between the reference lines to an accuracy of M.2 mm. Calculate the shrinkage in each direction as a percentage of the reference dimensions before aging. Average the results of the four specimens. 7. NOTES 7.1 Options - The following options must be specified in the application of this the standard: a. Width and length of PVC sheet (par. 4.9 and 4.10) b. Preformed shapes (par. 4.11) c. Colour (par. 4.12) d
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1