DIN 13-3-1999 ISO general purpose metric screw threads - Part 3 Nominal sizes for 0 5 mm fine pitch threads nominal diameter from 3 5 mm to 90 mm《ISO一般用途米制螺纹 第3部分 螺距0 5mm的细牙螺纹的标称尺寸.pdf

1、DEUTSCHE NORM November 1999 General purpose IS0 metric screw threads Part 3: Nominal sizes for 0,5 mm fine pitch threads with diameters from 33 mm to 90 mm DIN - 13-3 ICs 21.040.10 Supersedes December 1986 edition. Metrisches ISO-Gewinde allgemeiner Anwendung - Teil 3: Nennmae fr Feingewinde mit Ste

2、igung 0,5 mm - Gewinde-Nenndurchmesser von 3.5 mm bis 90 mm In keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Foreword This standard has been prepared by Technical Committee Gew

3、inde of the Normenausschu Technische Grundlagen (Fundamentals in Technology Standards Committee). The adoption of a number of IS0 Standards (e.g. IS0 724, IS0 965 series) as national standards led the responsible committee to revise the DIN 13 series of standards, The nominal sizes are now based bot

4、h on the basic dimensions specified in DIN IS0 724 and on the nominal profiles specified in DIN 13-19. The nominal sizes of the external thread minor diameters specified here have been calculated taking the root radius as being equal to H/6. The thread designation is to be found in DIN IS0 965-1. Se

5、e the table in the Explanatory notes of DIN 13-1 for an overview of DIN and DIN IS0 Standards for screw threads. Amendments This standard differs from the December 1986 edition in that the nominal sizes are now to be calculated on the basis of DIN 13-1 9 and size 7 mm threads have been assigned to s

6、eries 2 (cf. table 1). Previo us edit ions DIN 13-35: 1961 -01,1962-1 O, 1964-06; DIN 51 9: 1923-1 O, 1943-09,1952-12; DIN 13-3: 1970-03, 1986-1 2. All dimensions are in mm. 1 Scope This standard applies to general purpose IS0 metric screw threads. It specifies the nominal sizes for 0,5 mm fine pitc

7、h threads with diameters from 3,5 mm to 90 mm having the basic profile specified in DIN IS0 68-1 and the nominal profile specified in DIN 13-1 9. 2 Normative references This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited

8、 at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest editi

9、on of the publication referred to applies. DIN 13-19 General purpose IS0 metric screw threads - Nominal profiles DIN 13-21 General purpose IS0 metric screw threads - Limits of size for 1 mm to 24,5 mm diameter fine pitch threads with preferred tolerance classes DIN 13-22 General purpose IS0 metric s

10、crew threads - Limits of size for 25 mm to 52 mm diameter fine pitch threads with preferred tolerance classes Continued on pages 2 to 5. Translation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text. No pari of this translation may be

11、 reproduced without the prior permission of Ref. No. DIN 13-3 : 1999-1 V Deutsches Institut fur Normung e. V., Berlin. Luth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen). English price group O7 Sales No . 0107 04.00 Page 2 DIN 13-3 : 1999-1 1 DIN 13-2

12、3 DIN 2244 DIN IS0 68-1 General purpose IS0 screw threads - Basic profile - Part 1: Metric screw threads DIN IS0 724 DIN IS0 965-1 General purpose IS0 metric screw threads - Limits of size for 53 mm to 11 O mm diameter fine pitch threads with preferred tolerance classes Screw threads - Terminology (

13、IS0 68-1 : 1998) General purpose IS0 metric screw threads - Basic dimensions (IS0 724 : 1993) General purpose IS0 metric screw threads - Tolerances - Part 1 : Principles and basic data (IS0 965-1 : 1998) 3 Concepts See DIN 2244. 4 Dimensions and designation Nominal sizes shall be as shown in figure

14、1 and given in table 1. Choose series 1 diameters, series 2 diameters, or series 3 diameters (in order of preference). Screw threads with series 4 diameters are for special industrial applications only. Basic dimensions shall be as specified in DIN IS0 724, tolerances as in DIN IS0 965-1 and limits

15、of size as in DIN 13-21 to DIN 13-23. P=0,5 Internal thread p C 8 External thread - Diameters of internal thread H 6 1) R =-; the root profile may have a non-reversing curvature (cf. DIN IS0 965-1). Figure 1 : Nominal thread profile IS0 metric screw threads shall be designated in accordance with DIN

16、 IS0 965-1. t 1 6 - Diameters of external thread Page 3 DIN 13-3 : 1999-1 1 Table 1: Nominal diameter, d (= O) Series 1 Series 2 Series 3 Series 4 3,5 4,5 4 5 6 5,5 6,s 7,5 8,s 9 9,5 10,5 11 11,5 12,5 13 13,5 14,5 15 7 8 10 12 14 15,5 16,5 17,5 18,5 19,5 20,5 21,5 22,5 23,5 16 17 18 19 20 21 22 23 2

17、4 24,5 25,5 25 Nominal sizes Pitch diameter, Minor diameters, d3 Dl d2 (= 02) 3,175 2,887 2,959 3,675 3,387 3,459 4,175 3,887 3,959 4,675 4,387 4,459 5,175 4,887 4,959 5,675 5,387 5,459 6,175 5,887 5,959 6,675 6,387 6,459 7,175 6,887 6,959 7,675 7,387 7,459 8,175 7,887 7,959 8,675 8,387 8,459 9,175

18、8,887 8,959 9,675 9,387 9,459 10,175 9,887 9,959 10,675 10,387 10,459 11,175 10,887 10,959 11,675 11,387 11,459 12,175 11,887 11,959 12,675 12,387 12,459 13,175 12,887 12,959 13,675 13,387 13,459 14,175 13,887 13,959 14,675 14,387 14,459 15,175 14,887 14,959 15,675 15,387 15,459 16,175 15,887 15,959

19、 16,675 16,387 16,459 17,175 16,887 16,959 17,675 17,387 17,459 18,175 17,887 17,959 18,675 18,387 18,459 19,175 18,887 18,959 19,675 19,387 19,459 20,175 19,887 19,959 20,675 20,387 20,459 21,175 20,887 20,959 21,675 21,387 21,459 22,175 21,887 21,959 22,675 22,387 22,459 23,175 22,887 22,959 23,67

20、5 23,387 23,459 24,175 23,887 23,959 24,675 24,387 24,459 25,175 24,887 24,959 (continued) Page 4 DIN 13-3 : 1999-1 1 Table Nominal diameter, d (= O) Series 1 Series 2 Series 3 Series 4 26 26,5 27 27,5 28,5 29 29,5 28 30 30,5 31 31,5 32 32,5 33 33,5 34,5 35,5 36,5 37 37,5 38,5 39,5 40,5 41 41,5 34 3

21、5 36 38 39 40 42 42,5 43 43,5 44 44,5 45,5 46 46,5 47 47,5 45 48 1 (continued) Pitch diameter, Minor diameters, d3 Dl d2 (= 02) 25,675 25,387 25,459 26,175 25,887 25,959 26,675 26,387 26,459 27,175 26,887 26,959 27,675 27,387 27,459 28,175 27,887 27,959 28,675 28,387 28,459 29,175 28,887 28,959 29,6

22、75 29,387 29,459 30,175 29,887 29,959 30,675 30,387 30,459 31,175 30,887 30,959 31,675 31,387 31,459 32,175 31,887 31,959 32,675 32,387 32,459 33,175 32,887 32,959 33,675 33,387 33,459 34,175 33,887 33,959 34,675 34,387 34,459 35,175 34,887 34,959 35,675 35,387 35,459 36,175 35,887 35,959 36,675 36,

23、387 36,459 37,175 36,887 36,959 37,675 37,387 37,459 38,175 37,887 37,959 38,675 38,387 38,459 39,175 38,887 38,959 39,675 39,387 39,459 40,175 39,887 39,959 40,675 40,387 40,459 41,175 40,887 40,959 41,675 41,387 41,459 42,175 41,887 41,959 42,675 42,387 42,459 43,175 42,887 42,959 43,675 43,387 43

24、,459 44,175 43,887 43,959 44,675 44,387 44,459 45,175 44,887 44,959 45,675 45,387 45,459 46,175 45,887 45,959 46,675 46,387 46,459 47,175 46,887 46,959 47,675 47,387 47,459 (continued) Page 5 DIN 13-3 : 1999-1 1 Table Nominal diameter, d (= O) Series 1 Series 2 Series 3 Series 4 48,5 49 49,5 50 51 5

25、2 53 54 55 56 57 58 59 60 61 62 63 64 65 68 70 72 75 78 80 82 85 88 90 1 (concluded) Pitch diameter, Minor diameters, d3 Dl d2 (= 02) 48,175 47,887 47,959 48,675 48,387 48,459 49,175 48,887 48,959 49,675 49,387 49,459 50,675 50,387 50,459 51,675 51,387 51,459 52,675 52,387 52,459 53,675 53,387 53,45

26、9 54,675 54,387 54,459 55,675 55,387 55,459 56,675 56,387 56,459 57,675 57,387 57,459 58,675 58,387 58,459 59,675 59,387 59,459 60,675 60,387 60,459 61,675 61,387 61,459 62,675 62,387 62,459 63,675 63,387 63,459 64,675 64,387 64,459 67,675 67,387 67,459 69,675 69,387 69,459 71,675 71,387 71,459 74,675 74,387 74,459 77,675 77,387 77,459 79,675 79,387 79,459 81,675 81,387 81,459 84,675 84,387 84,459 87,675 87,387 87,459 89,675 89,387 89,459