DIN 16831-6-2003 Pipe fittings and joint assemblies for polybutene pressure pipes - Type PB 125 - Part 6 Dimensions of fittings for resistance welding《聚(异)丁烯压力管道用管道配件和连接组件 PB 125型 .pdf

1、 DEUTSCHE NORMSeptember 2003DIN 16831-6 ICS 23.040.45 Supersedes DIN 16831-6:2003-06 Pipe fittings and joint assemblies for polybutene pressure pipes Type PB 125 Part 6: Dimensions of fittings for resistance welding Rohrverbindungen und Formstcke fr Druckrohrleitungen aus Polybuten (PB) PB 125 Teil

2、6: Heizwendel-Schweifittings, Mae Document comprises 14 pagesTranslation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text. No part of this translation may be reproduced without prior permission of DIN Deutsches Institut fr Normung e.

3、 V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 8 www.din.de www.beuth.de !,k|s“09.06 9728980DIN 16831-6:2003-09 2 Contents Page Foreword.2 1 Scope .2 2 Normative references .2 3 Dimensions and designation.

4、3 4 Marking 12 Annex A (informative) Explanatory notes.13 Bibliography .14 Foreword This standard has been prepared by Technical Committee Fittings fr Druckrohre aus Thermoplasten of the Normenausschuss Kunststoffe (Plastics Standards Committee). Amendment This standard differs from DIN 16831-6:2003

5、-06 as follows: Figure 3 (type W1E) has been corrected. Previous editions DIN 16831-6: 2003-06 1 Scope This standard applies to injection-moulded1)resistance welding polybutene (PB) fittings as in DIN 16831-5 for resistance welding to polybutene pipes as in DIN 16968 and DIN 16969. The standard spec

6、ifies the dimensions of fittings for selected pipe diameters. NOTE Any relevant European Standards shall be observed. 2 Normative references This standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places i

7、n the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referr

8、ed to (including any amendments) applies. 1) “Injection-moulded” is defined in DIN EN ISO 472. DIN 16831-6:2003-09 3 DIN 16831-5, Pipe fittings and joint assemblies for type PB 125 polybutene pressure pipes General quality requirements and testing DIN 16901, Plastics mouldings Tolerances and accepta

9、nce conditions for linear dimensions DIN 16968, Polybutene (PB) pipes General quality requirements and testing DIN 16969, Type PB 125 polybutene pipes Dimensions DIN EN ISO 472, Plastics Vocabulary 3 Dimensions and designation 3.1 General The designs shown in figures 1 to 6 are for illustrative purp

10、oses only; however, the dimensions shall be as in tables 1 and 2. The limit deviation for angles shall be 2 and tolerances shall be as specified in DIN 16901, corresponding to tolerance class 160. 3.2 M1E socket, R1E reducer Figure 1 Type M1E socket2)Figure 2 Type R1E reducer3)Designation of a type

11、M1E socket for resistance welding, for use with SDR 11 series pipes with an outside diameter, d, of 25 mm: Socket DIN 16831 M1E 25 11 2) See table 1. 3) See table 1. DIN 16831-6:2003-09 4 Designation of a type R1E reducer for resistance welding, for use with SDR 11 series pipes, for reducing a spigo

12、t diameter d2= 25 mm to a pipe outside diameter of d o d1= 20 mm: Reducer DIN 16831 R1E 25 20 11 3.3 Type W1E 90 bend and type W2E 45 bend Figure 3 Type W1E 90 bend4)21min1dk = (1)Figure 4 Type W2E 45 bend5)2tan21min1=dk (2)Designation of a type W1E 90 bend for resistance welding, for use with SDR 1

13、1 series pipes with an outside diameter, d, of 25 mm: Bend DIN 16831 W1E 25 11 4) See table 1. 5) See table 1. DIN 16831-6:2003-09 5 Designation of a type W2E 45 bend for resistance welding, for use with SDR 11 series pipes with an outside diameter, d, of 25 mm: Bend DIN 16831 W2E 25 11 3.4 Equal 90

14、 tee (type T1E), branch reduced 90 tee (type Tr2E) Figure 5 Type T1E equal 90 tee6)21min1dk = (3)Figure 6 Type Tr2E branch reduced 90 tee7)22min1dk = (4)21min2dk = (5)6) See table 1. 7) See table 2. DIN 16831-6:2003-09 6 Designation of a type T1E equal tee for resistance welding, for use with SDR 11

15、 series pipes with an outside diameter, d, of 25 mm: Tee DIN 16831 T1E 25 11 Designation of a type Tr2E branch reduced tee for resistance welding, for use with SDR 11 series pipes, with an outside diameter d o d1= 25 mm and d o d2= 20 mm: Tee DIN 16831 Tr2E 25 20 11 DIN 16831-6:2003-09 7 Table 1 Dim

16、ensions of type M1E sockets, type R1E reducers, type W1E 90 bends, type W2E 45 bends, and type T1E equal 90 tees Dimensions in millimetres Mean outside diameterb Mean inside diameter in weld zoned Socket depth Weld length Face length Spigot lengthe Design dimensionsf Ovality Ovality Type Pipe outsid

17、e diameter as in DIN 16969a Limit deviation Limit deviationcLimit deviationcM1E R1E W1E T1E W2E d o d1d2d1t1t2t3t4k1k1k1k1of spigot of weld socket max. min. max. min. max. min. min. min. max. min. min. min. 16 20,0 03,0+0,4 16,1 0,3 15 35 10 5 15 37 0 29 8,0 3,3 16 16,1 0,3 20 25,0 03,0+0,5 20,1 0,3

18、 15 37 10 5 15 40 0 29 10,0 4,1 20 20,1 0,3 25 32,0 05,0+0,7 25,1 0,4 15 40 10 5 15 44 0 29 12,5 5,2 20 20,1 0,3 37 25 25,1 0,4 15 40 10 32 40,0 05,0+0,8 32,1 0,5 15 44 10 5 15 49 0 29 16,0 6,6 20 20,1 0,3 37 25 25,1 0,4 15 40 10 32 32,1 0,5 44 5 40 50,0 05,0+1,0 40,1 0,6 15 49 10 5 15 55 29 aNomina

19、l size bThe mean outside diameter of the spigot is calculated as the arithmetic mean of two measurements taken at right angles to each other at the mid-depth of the spigot. cOvality is the difference between the greatest and smallest inside diameter, measured on the same plane. dThe mean inside diam

20、eter is calculated as the arithmetic mean of two measurements taken at right angles to each other at the middle of the weld length at a distance (t3+ 0,5 t2) from the front face of the weld socket. eSocket depth of a pipe or fitting with spigot, not greater than half the total length of the fitting

21、in a joint without a stop. fDesign dimensions kminare minimum values and shall be calculated using equations (1) to (3), which can also be used to calculate kminfor pipe sizes not covered in table 1. DIN 16831-6:2003-09 8 Table 1 (continued) Dimensions in millimetres Mean outside diameterb Mean insi

22、de diameter in weld zoned Socket depth Weld length Face length Spigot lengthe Design dimensionsf Ovality Ovality Type Pipe outside diameter as in DIN 16969a Limit deviation Limit deviationcLimit deviationcM1E R1E W1E T1E W2E d o d1d2d1t1t2t3t4k1k1k1k1of spigot of weld socket max. min. max. min. max.

23、 min. min. min. max. min. min. min. 20 20,1 0,3 15 37 10 5 25 25,1 0,4 40 32 32,1 0,5 15 44 10 40 40,1 0,6 49 5 0 20,0 8,3 50 63,0 05,0+1,2 50,1 0,8 15 55 10 5 18 63 38 50 50,1 0,8 0 25,0 10,4 63 75,0 07,0+1,5 63,2 1 18 63 11 5 20 70 38 63 63,2 1 0 31,5 13,0 75 90,0 07,0+1,9 75,2 1,2 20 70 12 5 23 7

24、9 48 63 63,2 18 63 11 75 75,2 1,2 20 70 12 0 37,5 15,5 90 110 01+2,2 90,2 1,4 23 79 13 5 27 82 0 48 45,5 18,6 aNominal size bThe mean outside diameter of the spigot is calculated as the arithmetic mean of two measurements taken at right angles to each other at the mid-depth of the spigot. cOvality i

25、s the difference between the greatest and smallest inside diameter, measured on the same plane. dThe mean inside diameter is calculated as the arithmetic mean of two measurements taken at right angles to each other at the middle of the weld length at a distance (t3+ 0,5 t2) from the front face of th

26、e weld socket. eSocket depth of a pipe or fitting with spigot, not greater than half the total length of the fitting in a joint without a stop. fDesign dimensions kminare minimum values and shall be calculated using equations (1) to (3), which can also be used to calculate kminfor pipe sizes not cov

27、ered in table 1. DIN 16831-6:2003-09 9 Table 1 (concluded) Dimensions in millimetres Mean outside diameterb Mean inside diameter in weld zoned Socket depth Weld length Face length Spigot lengthe Design dimensionsf Ovality Ovality Type Pipe outside diameter as in DIN 16969a Limit deviation Limit devi

28、ationc Limit deviationc M1E R1E W1E T1E W2E d o d1d2d1t1t2t3t4k1k1k1k1of spigot of weld socket max. min. max. min. max. min. min. min. max. min. min. min. 110 110,3 27 82 15 5 0 55,0 22,8 125 125,3 30 87 16 5 0 140 140,3 33 92 18 5 0 160 160,4 1,5 37 98 20 5 0 aNominal size bThe mean outside diamete

29、r of the spigot is calculated as the arithmetic mean of two measurements taken at right angles to each other at the mid-depth of the spigot. cOvality is the difference between the greatest and smallest inside diameter, measured on the same plane. dThe mean inside diameter is calculated as the arithm

30、etic mean of two measurements taken at right angles to each other at the middle of the weld length at a distance (t3+ 0,5 t2) from the front face of the weld socket. eSocket depth of a pipe or fitting with spigot, not greater than half the total length of the fitting in a joint without a stop. fDesi

31、gn dimensions kminare minimum values and shall be calculated using equations (1) to (3), which can also be used to calculate kminfor pipe sizes not covered in table 1. DIN 16831-6:2003-09 10 Table 2 Type Tr2E branch reduced 90 tee Dimensions in millimetres Pipe outside diameter as in DIN 16969a Mean

32、 inside diameter at socket welding zonebSocket depth Weld length Front length Design dimensionsd d o Ovality Limit deviationc Ovality Limit deviationcd1d2d1d1d2t1t4t2t5t3& t6k1k2in run at outlet in run at outlet in run at outlet in run at outlet min. max. min. max. min. max. min. max. min. min. min.

33、 min. min. 20 16 20 20,1 0,3 16,1 0,3 15 37 15 35 5 8,0 10,0 25 16 25 16,1 35 8,0 12,5 25 20 25 25,1 0,4 20,1 0,3 15 40 15 37 10 10 5 10,0 12,5 32 16 32 16,1 35 8,0 16,0 32 20 32 20,1 0,3 37 10, 16,32 25 32 32,1 0,5 25,1 0,4 15 44 15 40 10 10 5 12,5 16,0 40 16 40 16,1 35 8,0 20,0 40 20 40 20,1 0,3 3

34、7 10, 20,40 25 40 25,1 0,4 40 12,5 20,0 40 32 40 40,1 0,6 32,1 0,5 15 49 15 44 10 10 5 16,0 20,0 50 16 50 16,1 35 8,0 25,0 50 20 50 20,1 0,3 37 10, 25,50 25 50 25,1 0,4 40 12,5 25,0 50 32 50 32,1 0,5 44 16,0 25,0 50 40 50 50,1 0,8 40,1 0,6 15 55 15 49 10 10 5 20,0 25,0 aNominal size bThe mean inside

35、 diameter is calculated as the arithmetic mean of two measurements taken at right angles to each other at the middle of the weld length at a distance (t3+ 0,5 t2or t6+ 0,5 t5) from the front face of the weld socket. cOvality is the difference between the greatest and smallest inside diameter, measur

36、ed on the same plane. dDesign dimensions kminare minimum values and shall be calculated using equations (4) and (5), which can also be used to calculate kminfor pipe sizes not covered in table 2. DIN 16831-6:2003-09 11 Table 2 (concluded) Dimensions in millimetres Pipe outside diameter as in DIN 169

37、69a Mean inside diameter at socket welding zonebSocket depth Weld length Front length Design dimensionsd d o Ovality Limit deviationc Ovality Limit deviationcd1d2d1d1d2t1t4t2t5t3& t6k1k2in run at outlet in run at outlet in run at outlet in run at outlet min. max. min. max. min. max. min. max. min. m

38、in. min. min. min. 63 16 63 16,1 35 8,0 31,5 63 20 63 20,1 0,3 37 10, 31,63 25 63 25,1 0,4 40 12,5 31,5 63 32 63 32,1 0,5 44 16,0 31,5 63 40 63 40,1 0,6 49 20,0 31,5 63 50 63 63,2 1 50,1 0,8 18 63 15 55 11 10 5 25,0 31,5 75 50 75 50,1 0,8 15 55 10 25,0 37,5 75 63 75 75,2 1,2 63,2 1,0 20 70 18 63 12

39、11 5 31,5 37,5 90 63 90 63,2 1,0 18 63 11 31,5 45,0 90 75 90 90,2 1,4 75,2 1,2 23 79 20 70 13 12 5 37,5 45,0 110 75 110 75,2 1,2 20 70 12 37,5 55,0 110 90 110 110,3 1,5 90,2 1,4 27 82 23 79 15 13 5 45,0 55,0 aNominal size bThe mean inside diameter is calculated as the arithmetic mean of two measurem

40、ents taken at right angles to each other at the middle of the weld length at a distance (t3+ 0,5 t2or t6+ 0,5 t5) from the front face of the weld socket. cOvality is the difference between the greatest and smallest inside diameter, measured on the same plane. dDesign dimensions kminare minimum value

41、s and shall be calculated using equations (4) and (5), which can also be used to calculate kminfor pipe sizes not covered in table 2. DIN 16831-6:2003-09 12 4 Marking Marking shall include the minimum details given in table 3, and shall be printed or stamped on fittings so as to remain legible throu

42、ghout their service life. NOTE The manufacturer shall not be liable if marking becomes illegible as a result of installation procedures, or of cleaning, or if fittings are painted, scratched or masked. Marking shall not cause any cracking or other damage which could affect the serviceability of the

43、assemblies. If marking is printed on the assemblies, its colour shall be set off clearly against the background. Table 3 Required marking details Detail Mark Number of relevant standarda DIN 16831 Manufacturers name or trademark e.g. xyz Diameter of connecting pipe e.g. 32 SDRb as in DIN 16969 e.g.

44、SDR 11 Material PB Place and date of productionc c aThis information may be applied directly to the fitting, or be on a label applied to it or the packaging. bNominal standard dimension ratio or pipe series of the appropriate pipe as in DIN 16969. cThe details given may be coded and shall give the p

45、roduction period and site. Marking as in clause 4 shall be implemented for fittings which are not covered by other standards or regulations for specific applications. DIN 16831-6:2003-09 13 Annex A (informative) Explanatory notes DIN 16831 is a seven-part series of basic standards which are the firs

46、t German standards dealing with the dimensions and quality requirements for polybutene (PB) fittings. The standards were largely developed on the basis of existing standards on fittings made from other plastics. Each type of bend and tee is illustrated together with an equation used to calculate the

47、 design dimension, minimum value kmin, and the same equations can be used to calculate kminfor nominal sizes not covered in this standard. DIN 16831-6:2003-09 14 Bibliography DIN EN 10204, Metallic products Types of inspection documents DIN EN ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) ISO 161-1:1996, Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series ISO 4065:1996, Thermoplastics pipes Universal wall thickness table