DIN 17560-2-2004 Ferrosilicon and Silicon - Part 2 Technical delivery conditions for silicon《硅铁和硅 第2部分 硅的交货技术条件》.pdf

1、DEUTSCHE NORM February 200417560-2Document comprises 3 pages. No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e.V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).Silico

2、n and ferrosiliconPart 2: Technical delivery conditions for siliconTranslation by DIN-Sprachendienst.In case of doubt, the German-language original should be consulted as the authoritative text.ICS 77.100Ferrosilicium und Silicium Teil 2: Technische Lieferbedingungenfr SiliciumIn keeping with curren

3、t practice in standards published by the International Organization for Standardization(ISO), a comma has been used throughout as the decimal marker.ForewordThis standard has been prepared by the Normenausschuss Nichteisenmetalle (Nonferrous Metals StandardsCommittee), Technical Committee Ferrolegie

4、rungen.AmendmentsThis standard differs from DIN 17560, December 1965 edition, in that it has been completely revised.Previous editionDIN 17560: 1965-12.1 ScopeThis standard specifies requirements for silicon as used as an alloying element for steelmaking and alu-minium foundry purposes and in the ch

5、emical industry (for silicone production and in semiconductor tech-nology).2 Normative referenceThis standard incorporates, by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the titles of the publications

6、are listedbelow. For dated references, subsequent amendments to or revisions of any of these publications apply tothis standard only when incorporated in it by amendment or revision. For undated references, the latestedition of the publication referred to applies.ISO 31-0 : 1992 Quantities and units

7、 Part 0: General principlesThis standard, together withDIN 17560-1, February 2004edition, supersedesDIN 17560, December 1965edition.English price group 5www.din.dewww.beuth.de09.04 9572324Page 2DIN 17560-2 : 2004-023 Designation3.1 Standard designationThe designation of silicon shall include either

8、the name (symbol) or the material number (cf. table 1).EXAMPLE:Designation of silicon of grade Si98 (material number: 0.3397):Silicon DIN 17560 Si98orSilicon DIN 17560 0.33973.2 Designation for order purposesEXAMPLE:Designation when ordering 5 000 kg of silicon as specified in this standard, of grad

9、e Si98 (material number:0.3397), particle size range (KG) 10 mm to 200 mm:5 000 kg silicon DIN 17560 Si98 KG 10-200or5 000 kg silicon DIN 17560 0.3397 KG 10-2004 Requirements4.1 CompositionThe composition of silicon shall be as specified in table 1.Table 1: Composition of siliconMaterial Composition

10、, as percentages by massname number Si Al4)CCa5)Fe Ti6)Si971) 0.3396Min. 96,0 Max. 97,9 2,0 (0,3) 0,6 0,8 0,10Si982) 0.3397Min. 98,0 Max. 98,5 1,0 (0,2) 0,3 0,5 0,06Si993) 0.3399Min. 98,6 Max. 99,5 0,8 (0,1) 0,2 0,4 0,041) Commercially referred to as off-grade silicon.2) Commercially referred to as

11、standard grade silicon.3) Silicon grades with low iron content (e.g. 0,15 % to 0,3 %) or low calcium content (0,01 % to 0,1 %)are supplied subject to agreement.4) For silicon grades for aluminium foundry purposes, the aluminium content is normally left unspecified.In the case of silicon for use in t

12、he chemical industry, the aluminium content (obtained by refining thesilicon) is normally 0,15 % to 0,3 %.5) Grades with low calcium content are obtained by refining the silicon.6) Grades for use in the chemical industry are normally to have a titanium content less 0,04 %.( ) Bracketed values are fo

13、r guidance only.4.2 Particle sizeThe particle size range is to be specified when ordering. Table 2 gives guideline values, with any other rangesbeing subject to agreement.Page 3DIN 17560-2 : 2004-02Table 2: Particle sizes4.3 Form suppliedSilicon may be supplied in lumps up to 300 mm long (commercial

14、ly referred to as KG 0-300), or in particle sizesas crushed or screened.The surface of the material should be free from foreign matter, such as sand, slag, etc. The proportion ofmacroscopic non-metallic inclusions or adhering particles shall not exceed 0,5 % (m/m) for particle sizes above5 mm.5 Anal

15、ysisThe method of analysis shall be at the manufacturers discretion, a state-of-the-art procedure being used incases of dispute.When rounding results, the specifications of clause 6 are to be observed.6 Rounding of resultsResults as calculated or observed are to be rounded following the rules set ou

16、t in Annex B of ISO 31-0. The valueis to be rounded in one step to the same number of places as are specified in this standard.The results shall be rounded as follows:a) if the figure following the last significant place is less than five, then the latter shall remain unchanged;b) if the figure foll

17、owing the last significant place is five or higher, the latter shall be increased by one.7 Marking, labelling, packaging, transport and storageUnless otherwise requested or agreed upon, marking, labelling and packaging shall be at the suppliers discre-tion.Silicon should be transported and stored so

18、 as to be protected against moisture, in accordance with relevantregulations.Permissible undersize, as aParticle size range, percentage of quantity suppliedPermissible oversizein mm Total Fines (lessthan 3 mm)Above 10 up to 200 15 410 % (m/m) of quantity sup-plied.From 3 to 25 10Where the material i

19、s suppliedin lumps, the maximum particleFrom 3 to 10 10size along two or three dimen-sions of a lump shall not exceedLess than 3 1,15 times the upper value ofthe range.plied.Where the material is supplied inlumps, the maximum particlesize along two or three dimen-1,15 times the upper value of therange.