DIN 22102-3-2014 Conveyor belts with textile plies for bulk goods - Part 3 Permanent joints《散装货物用织物叠层皮带输送机 第3部分 固定式连接》.pdf

1、January 2014 English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 53.040.20!%?Dw“2283384www.din.deD

2、IN 22102-3Conveyor belts with textile plies for bulk goods Part 3: Permanent joints,English translation of DIN 22102-3:2014-01Textil-Frdergurte fr Schttgter Teil 3: Nicht lsbare Frdergurtverbindungen,Englische bersetzung von DIN 22102-3:2014-01Courroies transporteuses textiles pour produits en vrac

3、Partie 3: Joints permanents,Traduction anglaise de DIN 22102-3:2014-01SupersedesDIN 22102-3:1991-04www.beuth.deDocument comprises 14 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.12.16DIN 22102-3:2014-01 A comma is used as th

4、e decimal marker. Contents Page Foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions 4 4 Dimensions, design and designation 4 4.1 Splices for conveyor belts with one ply (finger splice), for belt types 630/1 6 4.2 Splices for conveyor belts with two plies and reinforcing layer 8 4

5、.3 Splices for conveyor belts with two or more plies and bonding layers . 9 5 Splicing conveyor belts 14 5.1 General 14 5.2 Heating platens in vulcanizing machines . 14 6 Marking . 14 2 DIN 22102-3:2014-01 Foreword DIN 22102-3 has been reviewed and editorially revised to bring it in line with the cu

6、rrent rules of presentation. There are no European documents covering the same subject as this standard. The responsible German body involved in the preparation of this standard was Working Committee NA 045-02-05 AA Frdergurte of the Normenausschuss Kautschuktechnik (FAKAU) (Rubber Technology Standa

7、rds Committee). DIN 22102 consists of the following parts under the general title Conveyor belts with textile plies for bulk goods: Part 1: Dimensions, specifications, marking Part 2: Testing Part 3: Permanent joints Attention is drawn to the possibility that some of the elements of this document ma

8、y be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 22102-3:1991-04 as follows: a) it has been brought in line with the current rules of presentation; b) the standard has been editori

9、ally revised; c) figures have been revised. Previous editions DIN 22102-3: 1991-04 3DIN 22102-3:2014-01 1 Scope This standard describes splices for permanently splicing conveyor belts with textile plies as in DIN 22102-1 by means of either hot or cold splicing. See DIN 22102-1 for the symbols used.

10、2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amend

11、ments) applies. DIN 22102-1, Conveyor belts with textile plies for bulk goods Part 1: Dimensions, specifications, marking DIN 22101, Belt conveyors for loose bulk materials Basis for calculation and dimensioning 3 Terms and definitions 3.1 conveyor belt splice for conveyor belts with textile plies f

12、or bulk goods, the zone in which the textile plies at the ends of two lengths of belt are permanently “spliced”, i.e. joined together, for the purpose of load transmission 4 Dimensions, design and designation Different splice geometries are described below according to the minimum breaking load of t

13、he belt, the number of plies and the belt design. For all splice dimensions where the tolerance is not given, the tolerance shall be 2 %. Any extra thickness caused by the splice shall not exceed 3 mm. Designation of a conveyor belt splice for a type 400/1 conveyor belt: EXAMPLE Conveyor belt splice

14、 DIN 22102 - 400/1 4 DIN 22102-3:2014-01 When selecting the type of belt, the theoretical loss in breaking strength in the splice rverbshall be taken into account along the lines of DIN 22101, using the values given in Table 2*). Table 1 Loss in breaking strength Number of plies Loss in breaking str

15、ength in the splice rVerb.1 0,20 2 0,20a) 0,50b) 3 0,33 4 0,25 5 0,20 a)Splice with reinforcing interlayer and 2-step splice b)Splice without reinforcing interlayer Splices for conveyor belts with one textile ply, for belt types 500/1. Dimensions in millimetres Key 1 Seam strip 2 Cover (carrying sid

16、e) 3 Cover (running side) Figure 1 Overlapping splice Table 2 gives minimum step lengths and splice lengths for different types of conveyor belt. *)Translators note. The German original is incorrect here. It should read “Table 1”. 5DIN 22102-3:2014-01 Table 2 Minimum step lengths and splice lengths

17、Conveyor belt type Minimum step length lstSplice length lvmm200/1 250/1 250 315/1 400/1 300 500/1 350 4.1 Splices for conveyor belts with one ply (finger splice), for belt types 630/1 Dimensions in millimetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) 4 Covering fabric, e.g. wi

18、th interlocked ends Figure 2 Finger splice 6 DIN 22102-3:2014-01 Finger splice dimensions are specified in Table 3. Table 3 Finger splice dimensions Conveyor belt type Finger widtha bfmmFinger lengthb lf mm Length of covering fabricc ld mmSplice lengthd lv mm630/1 60 800 1 100 1 300 800/1 1 000 1 30

19、0 1 500 1 000/1 1 200 1 500 1 700 1 250/1 1 500 1 800 2 000 1 600/1 70 2 000 2 300 2 500 2 000/1 2 400 2 700 2 900 2 500/1 3 000 3300 3 500 3 150/1 3 800 4 100 4 300 aIn the edge zone the finger width shall be 0,5 bfblf 1,2 FBmincld= lf + 300 dlv= lf+ 500; if the covering fabric is put on an angle (

20、la 0,3 B), the splice length lvis calculated as follows: lv= lf + 500 + (0,3 B) The sides of the fingers shall not touch each other. The thickness of material between the fingers should be selected on the basis of the carcass and be 2 to 4 mm. The type of covering fabric, as regards strength and mat

21、erial, shall be specified by the splice manufacturer. 7DIN 22102-3:2014-01 4.2 Splices for conveyor belts with two plies and reinforcing layer Dimensions in millimetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) 4 Interlayer 5 Reinforcing interlayer 6 Rubber Figure 3 Splice with

22、 reinforcing interlayer Table 4 shows the minimum steps and splice lengths for different types of conveyor belt. Table 4 Minimum steps and splice lengths Conveyor belt type Minimum step length lstmmSplice length lvmm630/2 800/2 150 170 360 400 1000/2 1250/2 220 270 500 600 The breaking load of the r

23、einforcing interlayer shall correspond to the minimum breaking load of the conveyor belt. 8 DIN 22102-3:2014-01 4.3 Splices for conveyor belts with two or more plies and bonding layers Figure 4 Stepped splice 0,3 (1) = st st+ a(2) nst= number of plies 1 (3) In special cases the splice can also be re

24、ctangular, in which case la= 0. The following figures show splice designs for conveyor belts with two to five plies. Dimensions in millimetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) Figure 5 Conveyor belt with two plies: 1-step splice 9aDIN 22102-3:2014-01 Dimensions in mill

25、imetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) Figure 6 Conveyor belt with two plies: 2-step splice Dimensions in millimetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) Figure 7 Conveyor belt with three plies: 2-step splice 10 DIN 22102-3:2014-01 Dimensi

26、ons in millimetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) Figure 8 Conveyor belt with four plies: 3-step splice Dimensions in millimetres Key 1 Seam strip 2 Cover (carrying side) 3 Cover (running side) Figure 9 Conveyor belt with five plies: 4-step splice 11DIN 22102-3:2014-

27、01 Table 5 shows the minimum steps and splice lengths for conveyor belts with two plies. Table 5 Minimum steps and splice lengths for conveyor belts with two plies Conveyor belt type Minimum step length lstmmSplice length lvmm1-step 2-step 1-step 2-step 200/2 250/2 250 125 250 250 315/2 400/2 300 15

28、0 300 300 500/2 350 175 350 350 12 DIN 22102-3:2014-01 Table 6 shows the minimum steps and splice lengths for conveyor belts with more than two plies. Table 6 Minimum steps and splice lengths for conveyor belts with more than two plies Conveyor belt type Breaking load of one ply N/mm Minimum step le

29、ngth lstmmSplice lengthalvmm Number of steps nst315/3 80 to 100 150 300 2 400/3 500/3 630/4 125 to 160 200 400 400 600 2 2 3 800/4 1 000/5 1 250/5 200 to 250 250 750 1 000 1 000 3 4 4 1 600/5 2 000/5 315 to 400 300 1 200 4 2 500/5 3 150/5 500 to 630 350 1 400 4 aFor belt types other than those shown

30、 in this table, the splice length lvis to be calculated by determining the breaking load of one ply. The minimum step length lstfor this value is then to be taken from this table. The splice length is then: lv= lst (number of plies 1) Example: Conveyor belt type 1000/3 Breaking load of one ply: 1000

31、3= 333 N/mm Step length lstfor this value = 300 mm Splice length: lv= 300 (3 1) lv= 600 mm 13DIN 22102-3:2014-01 5 Splicing conveyor belts 5.1 General Suitable materials shall be used for splicing the different types of conveyor belt. 5.2 Heating platens in vulcanizing machines Heating platens shall

32、 extend at least 100 mm in the longitudinal direction beyond the length of the splice and on each side of the splice, and shall be at least 50 mm wider on each side than the conveyor belt. 6 Marking At the customers request, the splice may be permanently marked with the following sequence of symbols

33、: a) date of splice manufacture (month and year); b) manufacturers symbol; c) splice number; d) fitters symbol. The letters and numbers in the marking shall be at least 20 mm high with a line width of at least 3 mm. Groups of numbers and/or letters shall be separated by a space. EXAMPLE 4/11 NN 15 21 14