DIN 625-4-2010 Rolling bearings - Radial deep groove ball bearing - Part 4 With flanged outer ring《滚动轴承 径向深槽滚珠轴承 第4部分 凸缘外圈》.pdf

1、May 2010 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.

2、100.20!$p=“1772661www.din.deDDIN 625-4Rolling bearings Radial deep groove ball bearings Part 4: With flanged outer ringEnglish translation of DIN 625-4:2010-05Wlzlager Radial-Rillenkugellager Teil 4: Mit Flansch am AuenringEnglische bersetzung von DIN 625-4:2010-05Roulements Roulements radial billes

3、, gorges profondes Partie 4: Avec collet sur bague extrieureTraduction anglaise de DIN 625-4:2010-05SupersedesDIN 625-4:1987-08www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1204.11 DIN 625-4:2010-05 A comma is used as the decimal

4、 marker. Contents Page Foreword. 3 1 Scope . 4 2 Normative references . 4 3 Terms, definitions and symbols 4 4 Type, designation, dimensions . 4 4.1 General. 4 4.2 Type 5 4.3 Designation . 5 4.4 Dimensions and symbols 6 5 Material 9 6 Design 10 Annex A (informative) Explanatory notes 11 Bibliography

5、 . 12 Figure Figure 1 Type (notation) 5 Table Table 1 Dimensions, symbols 6 2 DIN 625-4:2010-05 Foreword This standard has been prepared by Working Committee NA 118-01-02 AA Kugellager und Spannlager einschlielich Teile, allgemeines Wlzlagerzubehr und Gehuse of the Normenausschuss Wlz- und Gleitlage

6、r (Rolling Bearings and Plain Bearings Standards Committee). Amendments This standard differs from DIN 625-4:1987-08 as follows: a) the standard has been completely revised; b) information on masses has been deleted from Table 1; c) the designation of the bearing width has been changed from C to B;

7、d) normative references have been updated. Previous editions DIN 625-4: 1987-08 3 DIN 625-4:2010-05 1 Scope This standard specifies dimensions and symbols for single row deep groove ball bearings with flanged outer ring. To satisfy practical needs of bearing users, this standard specifies deep groov

8、e ball bearings in sizes selected in accordance with the general dimension plan given in DIN 616. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest

9、 edition of the referenced document (including any amendments) applies. DIN 616, Rolling bearings Dimensions General plan DIN 620-1, Rolling bearings Gauging methods for dimensional and running tolerances DIN 620-2, Rolling bearings Tolerances for rolling bearings Tolerances for radial bearings DIN

10、620-4, Rolling bearings Rolling bearing tolerances Part 4: Radial internal clearance DIN 620-6, Rolling bearings Rolling bearing tolerances Part 6: Chamfer dimension limits DIN 623-1, Rolling bearings Fundamental principles Designation, marking DIN EN ISO 683-17, Heat-treated steels, alloy steels an

11、d free-cutting steels Part 17: Ball and roller bearing steels DIN ISO 1132-1, Rolling bearings Tolerances Part 1: Terms and definitions ISO 492, Rolling bearings Radial bearings Tolerances 3 Terms, definitions and symbols For the purposes of this document, the terms, definitions and symbols given in

12、 DIN 616 and DIN ISO 1132-1 apply. 4 Type, designation, dimensions 4.1 General The designs shown are for illustrative purposes only; however, the dimensions of deep groove ball bearings with flanged outer ring shall be as specified. Details of the inner design are not standardized. The symbols used

13、shall comply with DIN 623-1. 4 DIN 625-4:2010-05 4.2 Type See Figure 1 for design. Figure 1 Design (notation) 4.3 Designation Designation of a deep groove ball bearing with flanged outer ring of diameter series 8 with a bore diameter d = 10 mm, exteral diameter D = 19 mm and width B = 5 mm (denoted

14、by symbol 61800 R), tolerance class PN1), radial bearing clearance CN, cage at the manufacturers discretion: Deep groove ball bearing DIN 625 61800 R Designation of a deep groove ball bearing of diameter series 0 with a bore diameter d = 120 mm, external diameter D = 180 mm and width B = 28 mm (deno

15、ted by symbol 6024 R), tolerance class P6, radial bearing clearance C3 (P63), cage at the manufacturers discretion: Deep groove ball bearing DIN 625 6024 R-P63 1)In DIN 620-2:1988-02, valid at the time of publication of this standard, tolerance class PN in 4.3 of this standard is given as tolerance

16、class P0. This will be adjusted in a future revision of that standard. 5 DIN 625-4:2010-05 4.4 Dimensions and symbols Table 1 Dimensions, symbols Dimensions in millimetres r1s r2sD B D1C1min. Symbol 0,6 2,5 1 3,3 0,3 0,05 618/0,6 R 3 1 3,8 0,3 0,05 618/1 R 3 1,5 3,8 0,45 0,05 638/1 R 4 1,6 5 0,5 0,1

17、 619/1 R 1 4 2,3 5 0,6 0,1 639/1 R 4 1,2 5 0,4 0,05 618/1,5 R 4 2 5 0,6 0,05 638/1,5 R 5 2 6,5 0,6 0,15 619/1,5 R 5 2,6 6,5 0,8 0,15 639/1,5 R 1,5 6 2,5 7,5 0,6 0,15 60/1,5 R 5 1,5 6,1 0,5 0,08 618/2 R 5 2,3 6,1 0,6 0,08 638/2 R 6 2,3 7,5 0,6 0,15 619/2 R 6 3 7,5 0,8 0,15 639/2 R 2 7 2,8 8,5 0,7 0,1

18、5 602 R 6 1,8 7,1 0,5 0,08 618/2,5 R 6 2,6 7,1 0,8 0,08 638/2,5 R 7 2,5 8,5 0,7 0,15 619/2,5 R 7 3,5 8,5 0,9 0,15 639/2,5 R 2,5 8 2,8 9,5 0,7 0,15 60/2,5 R 7 2 8,1 0,5 0,1 618/3 R 7 3 8,1 0,8 0,1 638/3 R 8 3 9,5 0,7 0,15 619/3 R 8 4 9,5 0,9 0,15 639/3 R 9 3 10,5 0,7 0,15 603 R 10 4 11,5 1 0,15 623 R

19、 3 13 5 15 1 0,2 633 R 9 2,5 10,3 0,6 0,1 618/4 R 9 3,5 10,3 1 0,1 628/4 R 9 4 10,3 1 0,1 638/4 R 11 4 12,5 1 0,15 619/4 R 11 5 12,5 1,2 0,15 639/4 R 12 4 13,5 1 0,2 604 R 13 5 15 1 0,2 624 R 4 16 5 18 1 0,3 634 R 11 3 12,5 0,8 0,15 618/5 R 11 4 12,5 1 0,15 628/5 R 11 5 12,5 1 0,15 638/5 R 13 4 15 1

20、 0,2 619/5 R 13 6 15 1,2 0,2 639/5 R 14 5 16 1 0,2 605 R 16 5 18 1 0,3 625 R 5 19 6 22 1,5 0,3 635 R 6 DIN 625-4:2010-05 Table 1 (continued) r1s r2sd D B D1C1min. Symbol 13 3,5 15 1 0,15 618/6 R 13 5 15 1,1 0,15 628/6 R 13 6 15 1,1 0,15 638/6 R 15 5 17 1,2 0,2 619/65 R 15 7 17 1,5 0,2 639/6 R 17 6 1

21、9 1,2 0,3 606 R 19 6 22 1,5 0,3 626 R 6 22 7 25 1,5 0,3 636 R 14 3,5 16 1 0,15 618/7 R 14 5 16 1,1 0,15 628/7 R 14 6 16 1,1 0,15 638/7 R 17 5 19 1,2 0,3 619/7 R 17 7 19 1,5 0,3 639/7 R 19 6 22 1,5 0,3 607 R 22 7 25 1,5 0,3 627 R 7 26 9 29 2 0,3 637 R 16 4 18 1 0,2 618/8 R 16 5 18 1,1 0,2 628/8 R 16

22、6 18 1,3 0,2 638/8 R 19 6 22 1,5 0,3 619/8 R 19 9 22 1,8 0,3 639/8 R 22 7 25 1,5 0,3 608 R 24 8 26 2 0,3 628 R 8 28 9 30,25 2,25 0,3 638 R 17 4 19 1 0,2 618/9 R 17 5 19 1,1 0,2 628/9 R 17 6 19 1,3 0,2 638/9 R 20 6 23 1,5 0,3 619/9 R 20 9 23 1,8 0,3 639/9 R 24 7 27 1,5 0,3 609 R 26 8 28 2 0,3 629 R 9

23、 30 10 32,5 2,5 0,6 639 R 19 5 21 1 0,3 61800 R 19 6 21 1,3 0,3 62800 R 19 7 21 1,5 0,3 63800 R 22 6 25 1,5 0,3 61900 R 22 10 25 2 0,3 63900 R 26 8 28 2 0,3 6000 R 30 9 32,25 2,25 0,6 6200 R 10 35 11 37,75 2,75 0,6 6300 R 28 8 30 2 0,3 6001 R 32 10 34,5 2,5 0,6 6201 R 12 37 12 40 3 1 6301 R 32 9 34,

24、25 2,25 0,3 6002 R 35 11 37,75 2,75 0,6 6202 R 15 42 13 45 3 1 6302 R 35 10 37,5 2,5 0,3 6003 R 40 12 43 3 0,6 6203 R 17 47 14 50,5 3,5 1 6303 R 7 DIN 625-4:2010-05 Table 1 (continued) r1s r2sd D B D1C1min. Symbol 42 12 45 3 0,6 6004 R 47 14 50,5 3,5 1 6204 R 20 52 15 55,75 3,75 1,1 6304 R 44 12 47

25、3 0,6 60/22 R 50 14 53,5 3,5 1 62/22 R 22 56 16 60 4 1,1 63/22 R 47 12 50 3 0,6 6005 R 52 15 55,75 3,75 1 6205 R 25 62 17 66 4 1,1 6305 R 52 12 55 3 0,6 60/28 R 58 16 62 4 1 62/28 R 28 68 18 72,25 4,25 1,1 63/28 R 55 13 58,25 3,25 1 6006 R 62 16 66 4 1 6206 R 30 72 19 76,5 4,5 1,1 6306 R 58 13 61,25

26、 3,25 1 60/32 R 65 17 69,25 4,25 1 62/32 R 32 75 20 79,5 4,5 1,1 63/32 R 62 14 65,5 3,5 1 6007 R 72 17 76,25 4,25 1,1 6207 R 35 80 21 85 5 1,5 6307 R 68 15 71,75 3,75 1 6008 R 80 18 84,5 4,5 1,1 6208 R 40 90 23 95 5 1,5 6308 R 75 16 79 4 1 6009 R 85 19 89,75 4,75 1,1 6209 R 45 100 25 105,5 5,5 1,5 6

27、309 R 80 16 84 4 1 6010 R 90 20 95 5 1,1 6210 R 50 110 27 115,5 5,5 2 6310 R 90 18 94,5 4,5 1,1 6011 R 100 21 105,5 5,5 1,5 6211 R 55 120 29 126 6 2 6311 R 95 18 99,5 4,5 1,1 6012 R 110 22 115,5 5,5 1,5 6212 R 60 130 31 136,5 6,5 2,1 6312 R 100 18 104,5 4,5 1,1 6013 R 120 23 126 6 1,5 6213 R 65 140

28、33 147 7 2,1 6313 R 110 20 115 5 1,1 6014 R 125 24 131 6 1,5 6214 R 70 150 35 157,5 7,5 2,1 6314 R 115 20 120 5 1,1 6015 R 130 25 136,5 6,5 1,5 6215 R 75 160 37 167,5 7,5 2,1 6315 R 125 22 130,5 5,5 1,1 6016 R 140 26 146,5 6,5 2 6216 R 80 170 39 178,5 8,5 2,1 6316 R 8 DIN 625-4:2010-05 Table 1 (conc

29、luded) r1s r2sd D B D1C1min. Symbol 130 22 135,5 5,5 1,1 6017 R 150 28 157 7 2 6217 R 85 180 41 188,5 8,5 3 6317 R 140 24 146 6 1,5 6018 R 160 30 167,5 7,5 2 6218 R 90 190 43 199 9 3 6318 R 145 24 151 6 1,5 6019 R 170 32 178 8 2,1 6219 R 95 200 45 209,5 9,5 3 6319 R 150 24 156 6 1,5 6020 R 180 34 18

30、8,5 8,5 2,1 6220 R 100 215 47 225 10 3 6320 R 160 26 166,5 6,5 2 6021 R 190 36 199 9 2,1 6221 R 105 225 49 236 11 3 6321 R 170 28 177 7 2 6022 R 200 38 209,5 9,5 2,1 6222 R 110 240 50 251 11 3 6322 R 180 28 187 7 2 6024 R 215 40 225 10 2,1 6224 R 120 260 55 272 12 3 6324 R 200 33 208,5 8,5 2 6026 R

31、230 40 240 10 3 6226 R 130 280 58 294 14 4 6326 R 210 33 218,5 8,5 2 6028 R 140 250 42 261 11 3 6228 R 225 35 234 9 2,1 6030 R 150 270 45 282 12 3 6230 R 160 240 38 249,5 9,5 2,1 6032 R 170 260 42 270,5 10,5 2,1 6034 R 180 280 46 291,5 11,5 2,1 6036 R r1sSingle radial chamfer dimension. r2sSingle ax

32、ial chamfer dimension. 5 Material Balls and rings shall be made from ball and roller bearing steels as in DIN EN ISO 683-17. The material of the cage shall be at the manufacturers discretion or subject to agreement, with due consideration being given to DIN 623-1. 9 DIN 625-4:2010-05 6 Design Flange

33、 dimensions shall be as specified in DIN 616. Tolerances shall be as specified in DIN 620-2 or for flange diameter D1, as specified in ISO 492. Chamfer dimensions: Maximum values as specified in DIN 620-6. The radial internal clearance shall be as specified in DIN 620-4. Gauging methods for dimensio

34、nal and running tolerances shall be as specified in DIN 620-1. The cage design shall be at the manufacturers discretion or subject to agreement, with due consideration being given to DIN 623-1. Mass: Because cage design and cage material vary depending on the manufacturer, no information on mass is

35、provided. 10 DIN 625-4:2010-05 Annex A (informative) Explanatory notes The external dimensions of the deep groove ball bearings conform to ISO 15. 11 DIN 625-4:2010-05 12 Bibliography DIN 625-1, Rolling bearings Radial deep groove ball bearings Part 1: Single row DIN 625-3, Rolling bearings Radial d

36、eep groove ball bearings Part 3: Double row DIN 5418, Rolling bearings Dimensions for mounting DIN 5425-1, Rolling bearings Mounting tolerances General guidelines DIN ISO 76, Rolling bearings Static load ratings DIN ISO 281, Rolling bearings Dynamic load ratings and rating life ISO 15, Rolling bearings Radial bearings Boundary dimensions, general plan