DIN 7604-2016 Hexagon head screw plugs - Light type - Cylindrical thread《六角头螺塞 轻型 圆柱形螺纹》.pdf

1、May 2016 English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21.060.10!%Xb“2535763www.din.deDIN 76

2、04Hexagon head screw plugs Light type Cylindrical thread,English translation of DIN 7604:2016-05Verschlussschrauben mit Auensechskant Leichte Ausfhrung Zylindrisches Gewinde,Englische bersetzung von DIN 7604:2016-05Bouchons filets tte hexagonale Type troit Filetage cylindrique,Traduction anglaise de

3、 DIN 7604:2016-05SupersedesDIN 7604:2015-02www.beuth.deDocument comprises 9 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.08.16 DIN 7604:2016-05 2 A comma is used as the decimal marker. Contents Page Foreword . 3 1 Scope 4 2

4、Normative references 4 3 Symbols . 5 4 Dimensions 5 5 Technical delivery conditions . 7 6 Designation 8 Bibliography . 9 DIN 7604:2016-05 3 Foreword This document has been prepared by Working Committee NA 067-00-08 AA Verbindungselemente mit Sonderformen und aus Kunststoff of the DIN-Normenausschuss

5、 Mechanische Verbindungselemente (DIN Standards Committee Fasteners). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN and/or DKE shall not be held responsible for identifying any or all such patent rights. Amendments This stan

6、dard differs from DIN 7604:2015-02 as follows: a) the symbol m has been replaced by k in Figure 1 and Table 1; b) wrenching height kwhas been added in Figure 1 and Table 1; c) Type B has been deleted from Table 1; d) the reference to DIN 3852-1 for the type in the heading of Table 1 has been deleted

7、; e) in Table 1, “keg” has been deleted in the designation of the thread for Type C; f) the reference to DIN 158-1 for the metric fine pitch thread in the heading of Table 1 and accordingly in Clause 2 has been deleted; g) in Table 1, footnote b has been introduced stating that widths across flats a

8、ccording to DIN ISO 272 are to be explicitly agreed; h) Types B and C stud ends have been deleted from Table 2. Previous editions DIN 4610: 1931-02 DIN 7604: 1936-07, 1937x-11, 1941-02, 1944-07, 1947-05, 1956-08, 1959-11, 1973-01, 1983-06, 1992-01, 2015-02 DIN 7604:2016-05 4 1 Scope This standard sp

9、ecifies requirements for screw plugs which are intended to be screwed into holes with parallel thread as specified in DIN 13-5 or DIN 13-6. Such plugs are used together with a suitable seal ring, the type and material of which are to be selected as a function of the operating conditions (e.g. the me

10、dium, temperature, pressure, etc.). NOTE In deviation from the specifications of this standard, if screw plugs are intended to be used without a seal ring it is recommended that a Type B stud end according to DIN 3852-1 should be used. 2 Normative references The following documents, in whole or in p

11、art, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 475-1, Widths across flats for bolts, screws

12、, valves and fittings DIN 962, Bolts, screws, studs and nuts Designation, types and finishes DIN 3852-1, Stud ends and ports of fittings, valves and plug screws Part 1: Dimensions for metric fine pitch thread DIN EN 10263-2, Steel rod, bars and wire for cold heading and cold extrusion Part 2: Techni

13、cal delivery conditions for steels not intended for heat treatment after cold working DIN EN 10277-3, Bright steel products Technical delivery conditions Part 3: Free-cutting steels DIN EN 26157-3, Fasteners Surface discontinuities Bolts, screws and studs subject to special requirements DIN EN 28839

14、, Mechanical properties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanical properties of corrosion-resistant stainles

15、s steel fasteners Part 1: Bolts, screws and studs DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C DIN EN ISO 9717, Metallic and other inorganic coatings Phosphate conversion coating of metal

16、s DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN EN ISO 16048, Passivation of corrosion-resistant stainless steel fasteners DIN ISO 272, Fasteners Width across flats for hexagon products DIN ISO 965-1, ISO general purpose metric screw threads Tolerances Part 1: Prin

17、ciples and basic data DIN ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts DIN 7604:2016-05 5 3 Symbols The following symbols apply to screw plugs: dB1bore diameter in the shank i length of stud end t hole depth for dimensions over M16 1,5 Other relevant symbols and their d

18、escriptions are given in DIN EN ISO 225. 4 Dimensions See Figure 1 and Table 1. Dimensions in millimetres a) d 16 mm Other relevant dimensions and details as in Figure 1a). b) d 18 mm Key kwSee DIN EN ISO 4759-1 (kw,min= 0,7kmin) 1 Stud end according to DIN 3852-1, Type A a Centric elevation of 0,25

19、 mm for d 16 mm and of 0,50 mm for d 18 mm permitted if necessitated by turning process. b Recess as a result of manufacturing process permitted. c Cylindrical shoulder or radius 0,8 mm permitted. d Taper as a result of manufacturing process permitted. e Screw plugs can be supplied with an integrate

20、d permanent magnet (PM). The dimension 3,5 mm stands for the maximum permissible overhang. Dimensions and details of design and placement of the magnet are at the manufacturers discretion. f Screw thread chamfered to not more than 1,5 P (P = pitch). Figure 1 Dimensions of hexagon head pipe plug (not

21、ation) DIN 7604:2016-05 6 Table 1 Dimensions Dimensions in millimetres d c dwbdB1ebi ltk kwsbt MassaType Metric fine pitch thread as in DIN 13-5 and DIN 13-6 DIN 475-1 DIN ISO 272 DIN 475-1 DIN ISO 272 DIN 475-1 DIN ISO 272 (7,85 kg/dm3) kg/1 000 units +0,2 0 h14 h14 +0,5 0 min. min. 0,2 IT15 min. +

22、0,6 0,3 A with short stud end M10 1 0,5 14 13 15,33 14,20 6 10,5 4 2,63 14 13 12,8 M12 1,5 0,5 17 16 18,72 17,59 9 15,5 6 4,03 17 16 19,2 M14 1,5 0,5 19 18 20,88 19,85 9 15,5 6 4,03 19 18 24,6 M16 1,5 0,5 21 20 23,91 26,17 9 15,5 6 4,03 22 21 33,4 M18 1,5 2,0 23 23 10 18,72 17,59 9 17,0 6 4,03 17 16

23、 8 27,2 M22 1,5 2,0 27 27 14 20,88 19,85 9 17,0 6 4,03 19 18 8 34,3 M26 1,5 2,5 31 31 16 23,91 26,17 9 19,5 8 5,40 22 21 8 59,4 M30 1,5 2,5 36 36 20 23,91 26,17 9 19,5 8 5,40 22 21 8 69,5 C with long stud end M8 1 0,5 12 13 13,07 14,20 8 12,5 4 2,63 12 13 6,5 M10 1 0,5 14 13 15,33 14,20 8 12,5 4 2,6

24、3 14 13 9,6 M22 1,5 2,0 27 27 14 20,88 19,85 12 20,0 6 4,03 19 18 8 42,5 M26 1,5 2,5 31 31 16 23,91 22,78 12 22,5 8 5,40 22 21 10 68,5 M30 1,5 2,5 36 36 20 23,91 22,78 12 22,5 8 5,40 22 21 10 81,0 M38 1,5 3,0 44 44 26 23,91 22,78 12 23,0 8 5,40 22 21 10 118 M45 1,5 3,0 52 52 32 26,17 26,17 12 23,0 8

25、 5,40 24 24 10 163 M52 1,5 3,0 60 60 38 29,56 29,56 12 23,0 8 5,40 27 27 10 205 aDepending on the width across flats (SW) used, the values deviate slightly. bThe width across flats according to DIN ISO 272 shall be explicitly agreed (see designation examples in Clause 6). Unless otherwise stated, th

26、e widths across flats according to DIN 475-1 apply. DIN 7604:2016-05 7 5 Technical delivery conditions See Table 2. Table 2 Technical delivery conditions and standards to which reference is made Material Steel Stainless steel Nonferrous metals General requirements DIN ISO 8992 Thread size Tolerance

27、class 6g Standards DIN ISO 965-1 Mechanical properties Materiala11SMnPb30 C10C A1 to A5 Al1 to Al6 Cu1 to Cu7 Standards DIN EN 10263-2 DIN EN 10277-3 DIN EN ISO 3506-1bDIN EN 28839bLimit deviations, geometrical tolerances Product grade B Standard DIN EN ISO 4759-1 Stud end Type A Standard DIN 3852-1

28、 Surface finish Coating As processed. Plain. As processed. DIN EN ISO 9717 applies for phosphate coatings. Passivation as in DIN EN ISO 16048. DIN EN ISO 4042 applies with regard to electroplating. DIN EN ISO 10683 applies with regard to non-electrolytically applied zinc flake coatings. Surface cond

29、ition DIN EN 26157-3 applies with regard to limits for surface discontinuities. Acceptance inspection DIN EN ISO 3269 applies with regard to acceptance inspection. aThe use of other materials shall be subject to agreement. bFor screw plugs made of stainless steel or nonferrous metal, verification of

30、 compliance with the mechanical properties specified is not required. DIN 7604:2016-05 8 6 Designation EXAMPLE 1 A Type A screw plug with a short stud end, of thread size d = M22 1,5, made of steel (St), is designated as follows: Screw plug DIN 7604 A M22 1,5 St EXAMPLE 2 A screw plug as in the abov

31、e example with an integrated permanent magnet is designated as follows: Screw plug DIN 7604 A M22 1,5 St PM EXAMPLE 3 A Type C screw plug with a long stud end, of thread size d = M26 1,5, made of steel (St), with a width across flats SW 21 according to DIN ISO 272 is designated as follows: Screw plu

32、g DIN 7604 C M26 1,5 SW21 St EXAMPLE 4 A Type C screw plug with a long stud end, of thread size d = M26 1,5, re-rolled thread (Gn), made of steel (St), is designated as follows: Screw plug DIN 7604 C M26 1,5 Gn St NOTE The thread is re-rolled following coating in order to reduce the size of gouges.

33、Designation details for special design features are given in DIN 962. DIN 7604:2016-05 9 Bibliography 1 DIN 906, Internal drive pipe plugs Conical thread 2 DIN 908, Internal drive screw plugs with collar Cylindrical thread 3 DIN 909, Hexagon head pipe plugs Conical thread 4 DIN 910, Hexagon head scr

34、ew plugs with collar Cylindrical thread 5 DIN 5586, Compressed air equipment for rail vehicles Locking screws with collar and vent 6 DIN EN 10087, Free-cutting steels Technical delivery conditions for semi-finished products, hot-rolled bars and rods 7 DIN EN ISO 3506-2, Mechanical properties of corr

35、osion-resistant stainless steel fasteners Part 2: Nuts 8 DIN EN ISO 3506-3, Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress 9 DIN ISO 2768-1, General tolerances Tolerances for linear and angular dimensions without individual tolerance indications