DIN 906-2012 Internal drive pipe plugs Conical thread《内部传动螺旋塞 圆锥螺纹》.pdf

1、April 2012Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 21

2、.060.10!$x8“1928521www.din.deDDIN 906Internal drive pipe plugs Conical thread,English translation of DIN 906:2012-04Verschlussschrauben mit Innenantrieb Kegeliges Gewinde,Englische bersetzung von DIN 906:2012-04Bouchons filets entranement intrieur Filetage conique,Traduction anglaise de DIN 906:2012

3、-04SupersedesDIN 906:1992-01www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 12 pages01.13 DIN 906:2012-04 2 A comma is used as the decimal marker. Contents Page Foreword 3 1 Scope 4 2 Normative references . 4 3 Symbols 5 4 Dimensions an

4、d masses 6 5 Technical delivery conditions . 10 6 Designation . 11 Bibliograpy 12 DIN 906:2012-04 3 Foreword This standard has been prepared by Working Committee NA 067-00-08 AA Verbindungselemente mit Sonderformen und aus Kunststoff of the Normenausschuss Mechanische Verbindungselemente (Fasteners

5、Standards Committee). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. Amendments This standard differs from DIN 906:1992-01 as follows: a) pipe plugs

6、 with hexalobular socket and 12 point socket have been included; b) the title of the standard has been changed; c) symbol b has been replaced by lt; d) Clause 3 listing additional symbols and quantities has been added; e) Figure 1 has been revised and Figures 2 and 3 have been added; f) the technica

7、l delivery conditions have been completely revised, and the materials now also include aluminium alloys and copper-zinc alloys; g) normative references have been updated. Previous editions DIN 906: 1943-12, 1956-04, 1973-01, 1983-06, 1992-01 DIN 906:2012-04 4 1 Scope This standard specifies dimensio

8、ns, masses and technical delivery conditions for pipe plugs which are intended to be screwed into holes with parallel thread as specified in DIN 158-1, DIN 3858, DIN EN ISO 228-1 and DIN ISO 261. NOTE 1 Since tightness is a function of pressure, temperature, the materials involved and the fluid with

9、 which the threaded parts are in contact, such connections cannot be assumed to be tight. Therefore, it is recommended that a sealant or seal ring should be provided, particularly where the hole has a thread as specified in DIN ISO 261. NOTE 2 For pipe plugs for use in gas and water supply systems,

10、see the Technische Regeln fr Gasinstallationen (DVGW-TRGI) (DVGW Codes of practice for gas installations)1)and DIN 1988-2. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat

11、ed references, the latest edition of the referenced document (including any amendments) applies. DIN 158-1, Metric external taper screw threads and mating internal parallel screw threads Part 1: Nominal sizes, limit deviations, limits of size and verification DIN 267-2, Fasteners Technical delivery

12、conditions Design and dimensional accuracy DIN 1988-2, Drinking water supply systems Materials, components, appliances, design and installation (DVGW code of practice) DIN 3858, Whitworth pipe threads for pipe couplings Parallel internal thread and taper external thread Dimensions DIN 34824, 12 poin

13、t socket for bolts and screws DIN EN 10263-2, Steel rod, bars and wire for cold heading and cold extrusion Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working DIN EN 10277-3, Bright steel products Technical delivery conditions Part 3: Free-cutting stee

14、ls DIN EN 12476, Phosphate conversion coatings of metals Method of specifying requirements DIN EN 26157-3, Fasteners Surface discontinuities Bolts, screws and studs subject to special require-ments DIN EN 28839, Mechanical properties of fasteners Nonferrous metal bolts, screws, studs and nuts DIN EN

15、 ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and descriptions of dimensions DIN EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimen-sions, tolerances and designation DIN EN ISO 3269, Fasteners Acceptance inspection DIN EN ISO 3506-1, Mechanic

16、al properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs 1) Obtainable from ZfGW-Verlag GmbH, Voltastrae 79, 60486 Frankfurt (Main) DIN 906:2012-04 5 DIN EN ISO 4042, Fasteners Electroplated coatings DIN EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, scr

17、ews, studs and nuts Product grades A, B and C DIN EN ISO 10664, Hexalobular internal driving feature for bolts and screws DIN EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings DIN ISO 261, ISO general purpose metric screw threads General plan DIN ISO 8992, Fasteners General re

18、quirements for bolts, screws, studs and nuts DVGW G 600 * TRGI 86/96, Technische Regeln fr Gas-Installationen (Technical rules for gas installations) DVGW-TRGI 1986/1996 3 Symbols The following symbols shall apply to pipe plugs: C nominal diameter of 12 point socket drive (equal to d1 minaccording t

19、o DIN 34824) t1penetration depth of hexagon socket drive t2penetration depth of hexalobular socket drive t3penetration depth of 12 point socket drive Other relevant symbols and their descriptions are given in DIN EN ISO 225. DIN 906:2012-04 6 4 Dimensions and masses See Figures 1 to 3 and Table 1. a

20、Form of socket base at manufacturers discretion. bCentric elevation of 0,25 mm for d 24 mm and of 0,5 mm for d 24 mm permitted. cHexagon socket may be slightly rounded or countersunk to 1,2 smax. ddf (1,15 smax) + 0,5 mm (applies to turned parts only). eMaximum prebore diameter for turned parts with

21、 1,025 smax. fScrew thread chamfered to not more than 1,5 P (P = pitch). Figure 1 Dimensions of hexagon socket pipe plug (ISK) (notation) aForm of socket base at manufacturers discretion. bCentric elevation of 0,25 mm for d 24 mm and of 0,5 mm for d 24 mm permitted. cHexalobular socket (ISR) may be

22、slightly rounded or countersunk to 1,1 A. ddf A + 0,5 mm (applies to turned parts only). eMaximum prebore diameter for turned parts with 1,15 B. fScrew thread chamfered to not more than 1,5 P (P = pitch). Figure 2 Dimensions of pipe plug with hexalobular socket (ISR) as in DIN EN ISO 10664 (notation

23、) DIN 906:2012-04 7 aForm of socket base at manufacturers discretion. bCentric elevation of 0,25 mm for d 24 mm and of 0,5 mm for d 24 mm permitted. c12 point socket (IVZ) may be slightly rounded or countersunk to 1,1 C. ddf C + 0,5 mm (applies to turned parts only). eMaximum prebore diameter for tu

24、rned parts at manufacturers discretion. fScrew thread chamfered to not more than 1,5 P (P = pitch). Figure 3 Dimensions of pipe plug with 12 point socket (IVZ) as in DIN 34824 (notation) DIN 906:2012-04 8 Table 1 Dimensions of internal drive pipe plugs Dimensions in millimetres d Hexagon socket Hexa

25、lobular socket as in DIN EN ISO 10664 12 point socket as in DIN 34824 Massb(7,85 kg/dm3) kg/1 000 units Metric external taper screw thread as in DIN 158-1 Whitworth pipe thread as in DIN 3858 lteas t1t2t3w (short thread) Tolerance class 2 (short thread) js16 min. D12 min. No. min. Nominal size min.

26、min. M8 1 keg 8 4,6 4 4,0 25 2,0 N5 2,0 1,8 2,1 M10 1 keg R 1/8 8 5,7 5 4,0 30 2,5 N6 2,5 1,8 3,4 M12 1,5 keg 10 6,9 6 5,0 40 2,7 N8 2,9 2,0 6,10 R 1/4 10 8,0 7 5,0 40 2,7 N8 2,9 2,0 7,00 M14 1,5 keg 10 8,0 7 5,0 45 2,9 N8 2,9 2,0 8,10 M16 1,5 keg 10 9,2 8 5,0 50 3,7 N10 3,7 2,0 11,0 R 3/8 10 9,2 8

27、5,0 50 3,7 N10 3,7 2,0 12,2 M18 1,5 keg 10 9,2 8 5,0 50 3,7 N10 3,7 2,0 14,6 M20 1,5 keg 10 11,4 10 5,0 55 4,6 N12 4,6 2,0 17,6 R 1/2 10 11,4 10 5,0 55 4,6 N12 4,6 2,0 19,0 M22 1,5 keg 10 11,4 10 5,0 55 5,4 N14 5,4 2,0 22,0 M24 1,5 keg 12 13,7 12 6,0 60 6,4 N16 6,4 2,0 30,8 M26 1,5 keg 12 13,7 12 6,

28、0 60 6,4 N16 6,4 2,0 38,6 M27 2 keg R 3/4 12 13,7 12 6,0 60 6,4 N16 6,4 2,0 40,2 M30 1,5 keg M30 2 keg 12 19,4 17 6,0 80 7,3 N18 7,3 2,0 44,0 See page 9 for aand b. DIN 906:2012-04 9 Table 1 (continued) Dimensions in millimetres d Hexagon socket Hexalobular socket as in DIN EN ISO 10664 12 point soc

29、ket as in DIN 34824 Massb(7,85 kg/dm3) kg/1 000 units Metric external taper screw thread as in DIN 158-1 Whitworth pipe thread as in DIN 3858 lteas t1t2t3w (short thread) Tolerance class 2 acc. to standard js16 min. D12 min. No. min. Nominal size min. min. M33 2 keg R 1 12 19,4 17 6,0 80 7,3 N18 7,3

30、 2,0 57,5 M36 1,5 keg M36 2 keg 15 21,7 19 7,5 3,0 85,2 M38 1,5 keg 15 21,7 19 7,5 3,0 94,4 M39 2 keg 15 21,7 19 7,5 3,0 103,0 M42 1,5 keg M42 2 keg R 1 1/4 18 25,2 22 11,5 3,0 135,0 M45 1,5 keg M45 2 keg 18 25,2 22 11,5 3,0 167,0 M48 1,5 keg M48 2 keg R 1 1/2 20 27,4 24 11,5 4,0 214,0 M52 1,5 keg M

31、52 2 keg 20 27,4 24 11,5 4,0 253,0 M56 2 keg 22 36,6 32 13,0 4,0 274,0 M60 2 keg 22 36,6 32 13,0 4,0 350,0 aemin= 1,14 smin. bThe values deviate slightly for hexalobular sockets and 12 point sockets. DIN 906:2012-04 10 5 Technical delivery conditions See Table 2. Table 2 Technical delivery condition

32、s Material Steel Stainless steel Nonferrous metal General requirements DIN ISO 8992 Thread Tolerance class DIN 158-1: short thread/ DIN 3858: tolerance class 2 (short thread) Standards Mechanical properties Materialsa11SMnPb30 C10C A1 to A5 Al1 to Al6 Cu1 to Cu7 Standards DIN EN 10277-3, DIN EN 1026

33、3-2 DIN EN ISO 3506-1bDIN EN 28839 Limit deviations, geometrical tolerances Product grade B Standards DIN EN ISO 4759-1, DIN 267-2 Surface finish Coating As processed. As processed. DIN EN 12476 applies with regard to phosphating. DIN EN ISO 4042 applies with regard to electroplating. DIN EN ISO 106

34、83 applies with regard to non-electrolytically applied zinc flake coatings. Surface disontinuities DIN EN 26157-3 applies with regard to limits for surface discontinuities. Acceptance inspection DIN EN ISO 3269 applies with regard to acceptance inspection. aOther materials shall be subject to agreem

35、ent. bFor pipe plugs made of stainless steel verification of compliance with the mechanical properties specified is not required. DIN 906:2012-04 11 6 Designation Designation of a pipe plug with conical thread of thread size d = M20 1,5 and with hexagon socket, made of steel (St): Pipe plug DIN 906

36、M20 1,5 St Designation of a pipe plug with conical thread of thread size d = R 1/2 and with 12 point socket (IVZ), made of steel (St): Pipe plug DIN 906 R 1/2 IVZ St Designation of a pipe plug with conical thread of thread size d = R 1/2 and with hexalobular socket (ISR), made of AlSi1MgMn: Pipe plu

37、g DIN 906 R 1/2 ISR Al3 Designation of a pipe plug with conical thread of thread size d = M20 1,5 and with 12 point socket (IVZ), re-rolled thread (Gn), made of steel (St): Pipe plug DIN 906 M20 1,5 IVZ Gn St NOTE The thread is rolled once more following coating in order to reduce the size of gouges

38、. DIN 906:2012-04 12 Bibliography DIN 908, Internal drive screw plugs with collar Cylindrical thread DIN 909, Hexagon head pipe plugs Conical thread DIN 910, Hexagon head screw plugs with collar Cylindrical thread DIN 5586, Compressed air equipment for rail vehicles Locking screws with collar and ve

39、nt DIN 7604, Light-duty hexagon head screw plugs DIN EN 10087, Free-cutting steels Technical delivery conditions for semi-finished products, hot-rolled bars and rods DIN EN ISO 3506-2, Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts DIN EN ISO 3506-3, Mechanical p

40、roperties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress DIN ISO 2768-1, General tolerances Tolerances for linear and angular dimensions without individual tolerance indications ISO 9974-4, Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs