DIN EN 10034-1994 Structural steel I and H sections tolerances on shape and dimensions German version EN 10034 1993《I型和H型结构钢 形状和尺寸公差》.pdf

1、UDC 669.14.018.29-423.1 :621.713.1 DEUTSCHE NORM March 1994 I I Structural steel I and H sections English version of DIN EN 10034 Tolerances on shape and dimensions DIN - EN 10034 I- und H-Profile aus Baustahl; Grenzabmae und Formtoleranzen This standard, together with the March 1994 editions of DIN

2、 1025 Parts 2 to 5, supersedes the October 1963 editions of DIN 1025 Parts 2, 3 and 4 and the March 1965 edition of DIN 1025 Part 5. European Standard EN 10034:1993 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by ECISS/TC

3、11. The responsible German body involved in its preparation was the Normenausschu Eisen und Stahl (Steel and Iron Standards Committee), Technical Committee Warmgewalzte Profilerzeugnisse. The present standard specifies dimensional and geometrical tolerances for I and H sections and bearing piles, wh

4、ich had been given previously in DIN 1025 Parts 2 to 5. The values no longer apply for specific section shapes. The scope of the present standard covers many more sizes than the DIN Standards did, and includes, for example, a flange width of 420 mm and a flange thickness of 75 mm. Negoti- ations are

5、 continuing within ECISS/TC 11 for harmonizing the sizes of I and H sections. In specifying tolerances on the cross-sectional dimensions, ECISS/TC 11 endeavoured to specify values which, where lower limit deviations are chosen, do not lead to an automatic reduction of static parameters, which would

6、necessitate the use of higher factors of safety when designing the particular steel structure. These efforts resulted in an asymmetrical distribution of limit deviations, and in a reduction of the tolerance on nominal mass for single sections to * 4 %. The DIN Standards corresponding to the European

7、 Standard and EURONORMs referred to in clause 2 of the EN are as follows: EN Standard DIN Standard EN 1 O 079 DIN EN 10079 EURONORM 19 DIN 1025 Part 5 EURONORM 53 DIN 1025 Parts2 to 4 Standards referred to (and not included in Normative references) DIN EN 10079 Definition of steel products DIN 1025

8、Part 2 Hot rolled I and H sections (IPB and IB series); dimensions, mass and static parameters DIN 1025 Part 3 Hot rolled I and H sections (IPBI series); dimensions, mass and static parameters DIN 1025 Part 4 Hot rolled I and H sections (IPBv series); dimensions, mass and static parameters DIN 1025

9、Part 5 Hot rolled I and H sections (IPE series); dimensions, mass and static parameters Continued overleaf. EN comprises 5 pages. Beuth Verlag GmbH, Berlin, has the exclusive right of sale for German Standards (DIN-Normen). 07.94 DIN EN 10034 Engl. Price group 7 Sales No. 1107 Page 2 DIN EN 10034 Pr

10、evious editions DIN 1612: 09.24, 01.32, 03.43; DIN 1025 Part 2: 04.26, 10.28, 12.29, 04.32, 09.39, 07.40x, 07.59, 10.63; DIN 1025 Part 3: 10.63; DIN 1025 Part 4: 10.63; DIN 1025 Part 5: 03.65. Amendments In comparison with the October 1983 editions of DIN 1025 Parts2 to 4 and the March 1965 edition

11、of DIN 1025 Part 5, the following amendments have been made. a) The specifications have been restricted to dimensional and geometrical tolerances. b) Some of the limit deviations for section height, flange width and thickness and web thickness have been changed (cf. table 1). c) Some of the toleranc

12、es on parallelism of flange, section symmetry and straightness of web have been changed (cf, tables 2 and 3). d) The tolerance on nominal mass has been reduced to f 4 % EUROPEAN STANDARD EN 10034 NORME EUROPENNE EUROPAISCHE NORM September 1993 UDC 669.14.018.29-423.1 :621.713.1 Descriptors: Iron and

13、 steel products, I beams, Structural steels, dimensional tolerances, form tolerances. English version Structural steel I and H sections Tolerances on shape and dimensions POL .elles I E ?n acier de con- I- und H-Profile aus Stahl; Grenzabm und Formtoleranzen struction; tolrances de formes et de dime

14、nsions This European Standard was approved by CEN on 1993-08-30. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical re

15、ferences concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member

16、 into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden

17、, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels O 1993. Copyright reserved to all CEN members. Ref. No. EN 10034:1993 E Page 2 EN 10034:1993 Contents li

18、st Foreword Page .2 Tables Page 1 Scope . 2 1 : Dimensional tolerances for structural steel I and H sections .3 2 Normative references 2 3 Definitions 2: Tolerances on out-of-squareness and web off- . 2 centre of structural steel I and H sections . .4 4 Rolling tolerances for structural steel I and

19、H sections 3: Tolerances on straightness of structural steel I 2 and H sections 4 5 Toleranceonmass 5 6 Tolerance on length . 5 Annex A (informative) Straightness measurement . .5 Foreword This European Standard has been prepared by ECISSTTC 11 Sections: Tolerances and dimensions, the Secretariat of

20、 which is held by BSI. The discussions within ECISS/TC 11 were based on EURONORM 34-62 Broad flanged beams with parallel sides; rolling tolerances and EURONORM 44-63 Hot rolled IPE joists; rolling tolerances This European Standard shall be given the status of a national standard, either by publicati

21、on of an identical text or by endorsement, and conflicting national standards withdrawn, by March 1994 at the latest. In accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, G

22、reece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 1 Scope This standard specifies tolerances on the shape, dimensions and mass of structural steel I and H sections. These requirements do not apply to I and H sections rolled

23、from stainless steel, nor to taper flange sections. NOTE: Until a European Standard covering the dimensions of I and H beams is published, EURONORM 19 and EURONORM 53, or corres- ponding national standards, may be used. 2 Normative references This European Standard incorporates, by dated or undated

24、reference, provisions from other publications. These nor- mative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when in

25、corporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 10079 Definition of steel products EURONORM 19-57 IPE beams, parallel flanged beams EURONORM 53-62 Wide flanged beams with parallel flanges 3 Definitions For the purposes

26、of this European Standard, the definitions given in EN 10079 apply. 4 Rolling tolerances for structurai steel I and H sections 4.1 Section height (h) The deviation from the nominal section height, measured at the centreline of the web thickness, shall be within the tolerance given in table 1. Page 3

27、 EN 10034:1993 ! c Table 1: Dimensional tolerances for structural steel I and H sections -. b -I Section height, h ! ! ! X I c Nominal size mm bs110 110 700 ?% 14.0 Limit leviation mm + 3,O - 2,o + 4.0 - 2.0 + 5,O - 3.0 i 5.0 *) t shall be measured (see subclause 4.4). b at - 4 Flange width, b Limit

28、 Nominal size 1 devia;“ mm b325 4.2 Flange width (b) The deviation from the nominal flange width shall be within the tolerance given in table 1. 4.3 Web thickness (s) The deviation from the nominal web thickness, measured at the mid-point of dimension h, shall be within the toler- ance given in tabl

29、e 1. 4.4 Flange thickness (t) The deviation from the nominal flange thickness, measured at a point corresponding to one-fourth of the flange width, shall be within the tolerance given in table 1. Web thickness, s Limit Nominal size mm 1 devgon s110 Table 2 Tolerance on out-of-squareness and web off-

30、centre of structural steel I and H sections 2%ofb (max. 6,5 mm) L b h 360 Out-of-squareness k+k 0,l 96 of L Flange width, b Tolerance mm bi 110 I Web off-centre, e Flange width, b Tolerance mrn Table 3: Tolerances on straightness of structural steel I and H sections Where t c 40 mm bs 110 110 c b I

31、325 b 325 Where t 2 40 mm 110 c b I 325 50 b 325 I 8.0 I Section height, h Tolerance on straightness, I rnrn qxx and qYs I 80h180 I 0,30% ofL I I 180hj360 I 0,15% of L I Page 5 EN 10034:1993 5 Tolerance on mass The deviation from the nominal mass of a batch or an item shall not exceed f4,0%. The mas

32、s deviation is the difference between the actual mass of the batch or item and the calculated mass. The calculated mass shall be determined using a density of 735 kg/dm3. 6 Tolerance on length The sections shall be cut to ordered lengths, within tol- erances of: a) I50 mm, or b) tr 100 mm, where min

33、imum lengths are ordered. L represents the longest useable length of the section, assuming that the ends of the section have been cut square (see figure 1). I- Figure 1: Measurement of length L of I and H sections Annex A (informative) Straightness measurement Straightness measurement requires the u

34、se of a straight edge from which deviations in section straightness are measured. A taut string line is an acceptable straight edge, provided that deviations in the horizontal plane only are measured. Measurement for qxr shall be carried out as follows: The section is laid in the H position on a fla

35、t surface, and the string is taken from the outside of the centre of the flange width between the two ends of the unconstrained section. Measurement for qyy shall be carried out as follows: The section is laid in the I position on a flat surface, and the string is taken along the flange tip between the two ends of the unconstrained section.