DIN EN 10149-2-2013 Hot rolled flat products made of high yield strength steels for cold forming - Part 2 Technical delivery conditions for thermomechanically rolled steels German .pdf

1、December 2013 Translation by DIN-Sprachendienst.English price group 10No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 77.140.50!%*zW“2078752www.din.deDDIN EN 10149-2Hot rolled flat products made of high yield strength steels for coldforming Part 2: Technical delivery conditions for thermomechanically rolledsteels;English version EN 10149-2:2013,English translation of DIN EN 10149-2:2013-12Warmgewalzte Flacherzeu

3、gnisse aus Sthlen mit hoher Streckgrenze zumKaltumformen Teil 2: Technische Lieferbedingungen fr thermomechanisch gewalzte Sthle;Englische Fassung EN 10149-2:2013,Englische bersetzung von DIN EN 10149-2:2013-12Produits plats lamins chaud en aciers haute limite dlasticit pour formage froid Partie 2:

4、Conditions techniques de livraison des aciers obtenus par laminagethermomchanique;Version anglaise EN 10149-2:2013,Traduction anglaise de DIN EN 10149-2:2013-12SupersedesDIN EN 10149-2:1995-11www.beuth.deDocument comprises 15 pagesIn case of doubt, the German-language original shall be considered au

5、thoritative.11.13DIN EN 10149-2:2013-12 2 A comma is used as the decimal marker. National foreword This document (EN 10149-2:2013) has been prepared by Technical Committee ECISS/TC 103 “Structural steel other than reinforcements”, (Secretariat: DIN, Germany). The responsible German body involved in

6、its preparation was the Normenausschuss Eisen und Stahl (Iron and Steel Standards Committee), Working Committee NA 021-00-04-01 UA Sthle fr den Stahlbau. Amendments This standard differs from DIN EN 10149-2:1995-11 as follows: a) Clause 1 “Scope” has been revised; b) Clause 6 “Classification and des

7、ignation” has been modified; c) Subclause 7.4.1 “General” has been revised; d) Subclause 7.5.3 “Hot-dip zinc-coating” has been completely revised; e) in Clause 11 “Options”, option 13) has been added; f) steel grades S900MC and S960MC have been added in Tables 1, 2 and B.1; g) footnotes f and g have

8、 been added in Table 2; h) a Bibliography has been added; i) the standard has been editorially revised. Previous editions DIN EN 10149-2: 1995-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10149-2 September 2013 ICS 77.140.50 Supersedes EN 10149-2:1995English Version Hot rolled flat produc

9、ts made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels Produits plats lamins chaud en aciers haute limite dlasticit pour formage froid - Partie 2: Conditions techniques de livraison des aciers obtenus par laminage thermomca

10、nique Warmgewalzte Flacherzeugnisse aus Sthlen mit hoher Streckgrenze zum Kaltumformen - Teil 2: Technische Lieferbedingungen fr thermomechanisch gewalzte SthleThis European Standard was approved by CEN on 17 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations whic

11、h stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Eur

12、opean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members a

13、re the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, R

14、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and

15、 by any means reserved worldwide for CEN national Members. Ref. No. EN 10149-2:2013: EEN 10149-2:2013 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Information to be supplied by the purchaser .4 4.1 General 4 4.2 Options .5 5 Dimensions, mass and tole

16、rances .5 5.1 Dimensions and tolerances 5 5.2 Mass of steel 5 6 Classification and designation .5 6.1 Classification 5 6.2 Designation 5 7 Technical requirements 5 7.1 Steel manufacturing process .5 7.2 Delivery condition 5 7.3 Chemical composition 5 7.4 Mechanical properties .6 7.5 Technological pr

17、operties 6 7.5.1 Weldability 6 7.5.2 Formability 6 7.6 Surface finish .7 7.7 Internal soundness 7 8 Inspection and testing .7 8.1 General 7 8.2 Sampling .7 8.3 Test units 7 8.4 Verification of chemical composition 7 8.5 Preparation of samples and test pieces 8 8.6 Test methods 8 8.7 Retests and resu

18、bmission for testing .8 8.8 Inspection documents .8 9 Marking .8 10 Disputes 8 11 Options .8 Annex A (normative) Location of test pieces 11 Annex B (informative) Minimum inside bend radii for cold forming . 12 Bibliography . 13 DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 3 Foreword This document (EN

19、10149-2:2013) has been prepared by Technical Committee ECISS/TC 103 “Structural steel other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the lat

20、est by March 2014, and conflicting national standards shall be withdrawn at the latest by March 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such

21、 patent rights. This document supersedes EN 10149-2:1995. In comparison with EN 10149-2:1995, the following significant technical changes were made: Scope was modified; subclause 6.1 was revised; subclause 7.4.1 was modified; subclause 7.5.3 was completely revised; Option 13) was added in Clause 11;

22、 steel grades S900MC and S960MC were added in Tables 1, 2 and B.1; footnotes f and g were added in Table 2. The titles of the other Parts of this European Standard are: Part 1: General technical delivery conditions; Part 3: Technical delivery conditions for normalized or normalized rolled steels. Ac

23、cording to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germa

24、ny, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 4 1 Scope This European Standard, in addition

25、to EN 10149-1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming. The grades are given in Table 1 (chemical composition) and Table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given

26、in 7.2. The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of: 1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 MPa1)up to and including 460 MPa1); 1,5 mm to 16 mm for the steels which have a specified m

27、inimum yield strength of 500 MPa1)up to and including 700 MPa1); and from 2 mm up to 10 mm for the steels with a minimum yield stress in the range from 900 MPa1)to 960 MPa1). 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indi

28、spensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10029, Hot-rolled plates 3 mm thick or above - Tolerances on dimensions and shape EN 10051, Continuously h

29、ot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape EN 10149-1:2013, Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions EN ISO 14713-2:2009, Zinc coatings - Gu

30、idelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10149-1:2013 apply. 4 Information to be supplied by the

31、purchaser 4.1 General The information to be supplied by the purchaser shall be in accordance with EN 10149-1. 1) 1 MPa = 1 N/mm2. DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 5 4.2 Options The options given in EN 10149-1 and Clause 11 shall apply. 5 Dimensions, mass and tolerances 5.1 Dimensions and t

32、olerances The dimensions and tolerances shall be in accordance with EN 10149-1. For hot rolled plate tolerances, the basic requirements shall be in accordance with EN 10029, including thickness tolerances to class A, unless otherwise agreed at the time of the order. For plates cut from continuously

33、hot rolled strip, the thickness tolerances shall be in accordance with EN 10051. 5.2 Mass of steel The calculated mass of steel shall be determined in accordance with EN 10149-1. 6 Classification and designation 6.1 Classification The steel grades S315MC, S355MC, S420MC, S460MC, S500MC and S550MC of

34、 this European Standard are alloy quality steels and the steel grades S600MC, S650MC, S700MC, S900MC and S960MC of this European Standard are alloy special steels according to EN 10020. 6.2 Designation The designation shall comply with EN 10149-1. 7 Technical requirements 7.1 Steel manufacturing pro

35、cess The steel manufacturing process shall be in accordance with EN 10149-1. See EN 10149-1:2013, Clause 11, option 1). 7.2 Delivery condition The products shall be supplied in the thermomechanically rolled delivery condition. The surface protection of descaled products shall be in accordance with E

36、N 10149-1. See EN 10149-1:2013, Clause 11, option 2). 7.3 Chemical composition The requirements of EN 10149-1 shall apply. DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 6 The chemical composition determined by ladle analysis shall comply with the specified values of Table 1. See EN 10149-1:2013, Clause

37、 11, option 3). 7.4 Mechanical properties 7.4.1 General Under the inspection and testing conditions as specified in Clause 8 and in the delivery condition as specified in 7.2, the mechanical properties shall comply with the values given in Table 2. Heating of grades S900MC and S960MC above 400C is n

38、ot recommended. If the purchaser intends to heat grades S900MC and S960MC at temperatures above 400C, the mechanical properties after such heating should be agreed at the time of order. See EN 10149-1:2013, Clause 11, option 13). 7.4.2 Impact energy If agreed at the time of the order, the verificati

39、on of the impact energy value shall be carried out in accordance with EN 10149-1. See EN 10149-1:2013, Clause 11, option 5). 7.5 Technological properties 7.5.1 Weldability Weldability shall be in accordance with EN 10149-1. 7.5.2 Formability 7.5.2.1 General NOTE Recommendations regarding cold formin

40、g are laid down in CEN/TR 10347. The products supplied according to this standard are not suitable for hot forming. 7.5.2.2 Cold forming 7.5.2.2.1 General Annex B contains indicative values for the inside bend radii for cold forming. 7.5.2.2.2 Flangeability The products are suitable for flanging wit

41、hout cracking. 7.5.2.2.3 Roll forming The suitability for roll forming shall be in accordance with EN 10149-1. See EN 10149-1:2013, Clause 11, option 6). DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 7 7.5.3 Hot-dip zinc-coating For grades S315MC to S700MC, requirements for chemical composition of stee

42、ls to be hot-dip zinc coated shall be separately agreed between manufacturer and purchaser. EN ISO 1461 should be used to specify coating requirements. EN ISO 14713-2 provides further guidance, including information on the influence of various factors, including steel chemical composition, on the co

43、ating formation. Option 7) (see EN 10149-1:2013, Clause 11) can be used to order steels with a chemical composition required for hot-dip zinc coating. When option 7) is implemented, the purchaser and manufacturer shall agree with a steel composition (ladle analysis) of silicon and phosphorous accord

44、ing to either Category A (or steels satisfying the formula Si 0,03 % and Si+2.5P 0,09 %) or Category B (limited to 0,14 % 8 mm the minimum yield strength can be 20 MPae lower. e1MPa = 1N/mm2. fBending at 90 o, for thicknesses less than 3 mm minimum mandrel diameter 7t. gBending at 90 o, for thicknes

45、ses less than 3 mm minimum mandrel diameter 8t. DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 11 Annex A (normative) Location of test pieces This annex gives the location of test pieces. Table A.1 Location of test pieces Dimensions in millimetres Type of test Thickness of product Orientation of the tes

46、t pieces for widths of Distance of the test piece from the rolled surface 12 longitudinal longitudinal aRolled surface. DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 12 Annex B (informative) Minimum inside bend radii for cold forming Table B.1 Minimum inside bend radii for cold forming Designation of s

47、teel grade Minimum recommended inside bend radii for nominal thicknesses (t) in mm aSteel name Steel number t 3 3 6 S315MC S355MC S420MC S460MC S500MC S550MC S600MC S650MC S700MC S900MC S960MC 1.0972 1.0976 1.0980 1.0982 1.0984 1.0986 1.8969 1.8976 1.8974 1.8798 1.8799 0,25t 0,25t 0,5t 0,5t 1,0t 1,0

48、t 1,0t 1,5t 1,5t 3,5t 4,0t 0,5t 0,5t 1,0t 1,0t 1,5t 1,5t 1,5t 2,0t 2,0t 4,0t 4,5t 1,0t 1,0t 1,5t 1,5t 2,0t 2,0t 2,0t 2,5t 2,5t 4,5t 5,0t aThe values are applicable for bend angles 90. DIN EN 10149-2:2013-12 EN 10149-2:2013 (E) 13 Bibliography 1 CEN/TR 10347, Guidance for forming of structural steels in processing 2 EN 10020, Definition and classification of grades of steel 3 EN ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articles Specifications and test methods (ISO 1461) DIN EN 10149-2:2013-12