1、March 2014 DIN EN 10216-5 D ICS 77.140.75; 23.040.10 Supersedes DIN EN 10216-5:2004-11 and DIN EN 10216-5 Corrigendum 1: 2008-06 Seamless steel tubes for pressure purposes Technical delivery conditions Part 5: Stainless steel tubes; English version EN 10216-5:2013, English translation of DIN EN 1021
2、6-5:2014-03 Nahtlose Stahlrohre fr Druckbeanspruchungen Technische Lieferbedingungen Teil 5: Rohre aus nichtrostenden Sthlen; Englische Fassung EN 10216-5:2013, Englische bersetzung von DIN EN 10216-5:2014-03 Tubes en acier sans soudure pour service sous pression Conditions techniques de livraison P
3、artie 5: Tubes en aciers inoxydables; Version anglaise EN 10216-5:2013, Traduction anglaise de DIN EN 10216-5:2014-03 Document comprises 48 pages Translation by DIN-Sprachendienst. In case of doubt, the German-language original shall be considered authoritative. No part of this translation may be re
4、produced without prior permission of DIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen). English price group 18 www.din.de !%, b) for non-destructive testing, reference is made to EN ISO 10893;
5、c) for tensile testing, reference is made to EN ISO 6892 and for the impact test, reference is made to EN ISO 148-1; d) for flattening test, drift expanding test, ring expanding test and ring tensile test, reference is made to EN ISO 8492, EN ISO 8493, EN ISO 8495 and EN ISO 8496; e) the standard ha
6、s been editorially revised. Previous editions DIN 17440: 1967-01, 1972-12 DIN 17458: 1985-07 DIN 17459: 1992-09 DIN EN 10216-5: 2004-11 DIN EN 10216-5 Corrigendum 1: 2008-06 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10216-5 December 2013 ICS 23.040.10; 77.140.75 Supersedes EN 10216-5:2004
7、 English Version Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 5: Stainless steel tubes Tubes sans soudure pour service sous pression - Conditions techniques de livraison - Partie 5: Tubes en aciers inoxydables Nahtlose Stahlrohre fr Druckbeanspruchungen - Technis
8、che Lieferbedingungen - Teil 5: Rohre aus nichtrostenden Sthlen This European Standard was approved by CEN on 17 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard w
9、ithout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any oth
10、er language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,
11、 Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMM
12、ITTEE FOR STANDARDIZATION C OM I T EUR O P EN DE NOR M A L I S ATI O N EUR O P I S C HES KOM I TE E F R NOR M UNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN
13、 10216-5:2013 E DIN EN 10216-5:2014-03 EN 10216-5:2013 (E) 2 Contents Page Foreword 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Symbols 6 5 Classification and designation . 7 5.1 Classification 7 5.2 Designation 7 6 Information to be supplied by the purchaser . 7 6.1 Mandatory
14、 information 7 6.2 Options . 7 6.3 Examples of an order 8 7 Manufacturing process . 9 7.1 Steelmaking process . 9 7.2 Tube manufacture and delivery conditions 9 8 Requirements . 10 8.1 General 10 8.2 Chemical composition 10 8.3 Mechanical properties . 16 8.4 Corrosion resistance . 25 8.5 Appearance
15、and soundness . 25 8.6 Straightness . 26 8.7 Preparation of ends . 26 8.8 Dimensions, masses and tolerances. 27 9 Inspection . 28 9.1 Type of inspection . 28 9.2 Inspection documents. 28 9.3 Summary of inspection and verification testing 29 10 Sampling . 29 10.1 Test unit 29 10.2 Preparation of samp
16、les and test pieces 31 11 Verification test methods 32 11.1 Chemical analysis 32 11.2 Tensile test . 32 11.3 Technological tests . 33 11.4 Impact test 34 11.5 Intergranular corrosion test 35 11.6 Leak tightness test 35 11.7 Dimensional inspection 36 11.8 Visual examination 36 11.9 Non-destructive te
17、sting. 36 11.10 Material identification 36 11.11 Retests, sorting and reprocessing. 36 12 Marking . 36 12.1 Marking to be applied 36 12.2 Additional marking 37 13 Handling and packaging . 37 Annex A (informative) Reference data of strength values for creep rupture of austenitic steels in the solutio
18、n annealed condition. 38 DIN EN 10216-5:2014-03 EN 10216-5:2013 (E) 3 Annex B (informative) Technical changes from the previous edition . 44 Annex ZA (informative) Clauses of this part of EN 10216 addressing essential safety requirements of the EU Directive 97/23/EC 45 Bibliography 46 DIN EN 10216-5
19、:2014-03 EN 10216-5:2013 (E) 4 Foreword This document (EN 10216-5:2013) has been prepared by Technical Committee ECISS/TC 110 “Steel tubes and fittings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by public
20、ation of an identical text or by endorsement, at the latest by June 2014, and conflicting national standards shall be withdrawn at the latest by June 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall n
21、ot be held responsible for identifying any or all such patent rights. This document supersedes EN 10216-5:2004. For the list of the most significant technical changes that have been made in this new edition, see Annex B. This document has been prepared under a mandate given to CEN by the European Co
22、mmission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This European Standard consists of the following parts, under the general title “Seam
23、less steel tubes for pressure purposes Technical delivery conditions“: Part 1: Non-alloy steel tubes with specified room temperature properties; Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties; Part 3: Alloy fine grain steel tubes; Part 4: Non-alloy and alloy s
24、teel tubes with specified low temperature properties; Part 5: Stainless steel tubes (the present document). Another European Standard series covering tubes for pressure purposes is: EN 10217, Welded steel tubes for pressure purposes Technical delivery conditions. According to the CEN-CENELEC Interna
25、l Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Irel
26、and, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 10216-5:2014-03 EN 10216-5:2013 (E) 5 1 Scope This European Standard specifies the technical delivery conditions in
27、two test categories for seamless tubes of circular cross section made of austenitic (including creep resisting steel) and austenitic-ferritic stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperatures or at elevated temperatures. NOTE On
28、ce this standard is published in the Official Journal of the European Union (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESR) of Directive 97/23/EC is limited to technical data of materials in this standard and does not presume adequacy of the mate
29、rial to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive are satisfied, needs to be done by the designer or
30、manufacturer of the pressure equipment, taking also into account the subsequent manufacturing processes which may affect properties of the base materials. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its ap
31、plication. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10020, Definitions and classification of grades of steel EN 10021, General technical delivery conditions for steel products EN
32、 10027-1, Designation systems for steels - Part 1: Steel names EN 10027-2, Designation systems for steels - Part 2: Numerical system EN 10028-7:2007, Flat products made of steels for pressure purposes - Part 7: Stainless steels EN 10052, Vocabulary of heat treatment terms for ferrous products EN 100
33、88-1:2005, Stainless steels - Part 1: List of stainless steels EN 10168:2004, Steel products - Inspection documents - List of information and description EN 10204:2004, Metallic products - Types of inspection documents EN 10266, Steel tubes, fittings and structural hollow sections - Symbols and defi
34、nitions of terms for use in product standards CEN/TR 10261, Iron and steel - Review of available methods of chemical analysis EN ISO 148-1:2010, Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1:2009) EN ISO 377, Steel and steel products - Location and preparation of
35、samples and test pieces for mechanical testing (ISO 377) EN ISO 643, Steels - Micrographic determination of the apparent grain size (ISO 643) EN ISO 2566-2, Steel - Conversion of elongation values - Part 2: Austenitic steels (ISO 2566-2) EN ISO 3651-2:1998, Determination of resistance to intergranul
36、ar corrosion of stainless steels - Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) DIN EN 10216-5:2014-03 EN 10216-5:2013 (E) 6 EN ISO 6892-1:2009, Metallic materials - Tensile testing - Part 1: Metho
37、d of test at room temperature (ISO 6892-1:2009) EN ISO 6892-2:2011, Metallic materials - Tensile testing - Part 1: Method of test at elevated temperature (ISO 6892-2:2011) EN ISO 8492, Metallic materials - Tube - Flattening test (ISO 8492) EN ISO 8493, Metallic materials - Tube - Drift expanding tes
38、t (ISO 8493) EN ISO 8495, Metallic materials - Tube - Ring expanding test (ISO 8495) EN ISO 8496, Metallic materials - Tubes - Ring tensile test (ISO 8496) EN ISO 10893-1:2011, Non-destructive testing of steel tubes - Part 1: Automated electromagnetic testing of seamless and welded (except submerged
39、 arc-welded) steel tubes for the verification of hydraulic leak- tightness (ISO 10893-1:2011) EN ISO 10893-8:2011, Non-destructive testing of steel tubes - Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of laminar imperfections (ISO 10893-8:2011) EN ISO 108
40、93-10:2011, Non-destructive testing of steel tubes - Part 10: Automated full peripheral ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of longitudinal and/or transverse imperfections (ISO 10893-10:2011) EN ISO 14284:2002, Steel and iron - Sampli
41、ng and preparation of samples for the determination of the chemical composition (ISO 14284:1996) ISO 11484:2009, Steel products - Employers qualification system for non-destructive testing (NDT) personnel 3 Terms and definitions For the purposes of this document, the terms and definitions given in E
42、N 10020, EN 10021, EN 10052 and EN 10266 and the following apply. 3.1 test category classification that indicates the extent and level of inspection and testing 3.2 employer organization for which a person works on a regular basis Note 1 to entry: The employer may be either the tube manufacturer or
43、supplier or a third party organization providing Non- Destructive Testing (NDT) services. 4 Symbols For the purposes of this document, the symbols given in EN 10266 and the following apply: TC test category NOTE See also Table 1 for symbols of the delivery condition. DIN EN 10216-5:2014-03 EN 10216-
44、5:2013 (E) 7 5 Classification and designation 5.1 Classification According to the classification system in EN 10020, the steel grades are classified as: austenitic steels (corrosion resisting or creep resisting steels); austenitic-ferritic steels. For more details see EN 10088-1. 5.2 Designation For
45、 the tubes covered by this document, the steel designation consists of: number of this part of EN 10216 (EN 10216-5); plus either steel name in accordance with EN 10027-1; or steel number allocated in accordance with EN 10027-2. 6 Information to be supplied by the purchaser 6.1 Mandatory information
46、 The following information shall be supplied by the purchaser at the time of enquiry and order: a) quantity (mass or total length or number); b) term “tube“; c) dimensions (outside diameter D and wall thickness T) (see 8.8.1); d) designation of the steel grade according to this part of EN 10216 (see
47、 5.2); e) test category (see 9.3). 6.2 Options A number of options are specified in this part of EN 10216 and these are listed below. In the event that the purchaser does not indicate a wish to implement any of these options at the time of enquiry and order, the tube shall be supplied in accordance
48、with the basic specification (see 6.1). 1) information about steelmaking process (see 7.1); 2) delivery condition (see 7.2.4); 3) specified range for sulphur content (see Table 2, footnote b); 4) product analysis (see 8.2.2); DIN EN 10216-5:2014-03 EN 10216-5:2013 (E) 8 5) additional verifications o
49、f mechanical properties on samples which have undergone a different or additional heat treatment (see 8.3.1); 6) verification of impact energy at room temperature (see 8.3.1); 7) agreed mechanical properties at room temperature for austenitic corrosion resisting steel tubes with wall thicknesses greater than 60 mm (see Table 6, footnote a); 8) agreed mechanical properties at room temperature for austenitic creep resisting steel tubes with wall thicknesses greater than 50 mm (see Table 7, footn
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1