1、June 2012Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91
2、.100.25!$|ev“1896683www.din.deDDIN EN 1024Clay roofing tiles for discontinuous laying Determination of geometric characteristicsEnglish translation of DIN EN 1024:2012-06Tondachziegel fr berlappende Verlegung Bestimmung der geometrischen KennwerteEnglische bersetzung von DIN EN 1024:2012-06Tuiles de
3、 terre cuite pour pose en discontinu Dtermination des caractristiques gomtriquesTraduction anglaise de DIN EN 1024:2012-06SupersedesDIN EN 1024:1997-06www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 20 pages05.12 DIN EN 1024:2012-06 2 A
4、 comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding” (Secretariat: NBN, Belgium). The responsible German body involved in its preparation was the Norm
5、enausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee 005-02-03 AA Dachziegel (SpA zu CEN/TC 128/SC 3). Amendments This standard differs from DIN EN 1024:1997-06 as follows: a) in Equation (8) for calculating the twist coefficient (5.3.1 “Twist”) the difference
6、 height has been replaced by the absolute value of the difference height; b) the standard has been editorially revised. Previous editions DIN 453: 1921-06, 1943-12 DIN 454: 1922-10 DIN 52250 = DIN DVM 2250: 1937-11 DIN 456: 1937x-11, 1958-05, 1976-08 DIN EN 1024: 1997-06 EUROPEAN STANDARD NORME EURO
7、PENNE EUROPISCHE NORM EN 1024 March 2012 ICS 91.100.25 Supersedes EN 1024:1997English Version Clay roofing tiles for discontinuous laying - Determination of geometric characteristics Tuiles de terre cuite pour pose en discontinu - Dtermination des caractristiques gomtriques Tondachziegle fr berlappe
8、nde Verlegung - Bestimmung der geometrischen Kennwerte This European Standard was approved by CEN on 22 January 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without a
9、ny alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other langu
10、age made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark
11、, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CE
12、N All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1024:2012: EEUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG EN 1024:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative referenc
13、es 43 Symbols 44 Test pieces .55 Tests methods 56 Test report . 17Annex A (informative) Example of twist measurement device for tiles with sidelock and headlock, tiles with sidelock only and overlapping tiles 18DIN EN 1024:2012-06 EN 1024:2012 (E) 3 Foreword This document (EN 1024:2012) has been pre
14、pared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
15、 the latest by September 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying
16、 any or all such patent rights. This document supersedes EN 1024:1997. This European Standard is one of the series of standards dealing with clay roofing tiles as listed below: EN 1304, Clay roofing tiles and fittings Products definitions and specifications EN 538, Clay roofing tiles for discontinuo
17、us laying Flexural strength test EN 539, Clay roofing tiles for discontinuous laying Determination of physical characteristic This European Standard includes: an informative annex Figure A.1 Example of twist measurement device for tiles with sidelock and headlock, tiles with sidelock only and overla
18、pping tiles. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ice
19、land, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1024:2012-06 EN 1024:2012 (E) 4 1 Scope This European standard specifies the methods for determining the g
20、eometric characteristics of clay tiles as defined in EN 1304, Clay roofing tiles and fittings Product definitions and specifications. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated
21、references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1304, Clay tiles and fittings Product definitions and specifications 3 Symbols L1maximum distance when measuring covering dimensions (length) in mi
22、llimetres (mm); L2minimum distance when measuring covering dimensions (length) in millimetres (mm); l1maximum distance when measuring covering dimensions (width) in millimetres (mm); l2minimum distance when measuring covering dimensions (width) in millimetres (mm); L mean cover length in millimetres
23、 (mm); LMmaximum cover length in millimetres (mm); l mean cover width in millimetres (mm); lMmaximum cover width in millimetres (mm); H difference in height from the measuring point at the support bar or height in relation to a reference plane in millimetres (mm); C twist coefficient in percent; A t
24、ile length as declared by the manufacturer in millimetres (mm); B tile width as declared by the manufacturer in millimetres (mm); hdheight of camber as declared by the manufacturer in millimetres (mm); hmmeasured height of camber in millimetres (mm); R camber in percentage; h hm-hd absolute value in
25、 millimetres (mm); LTtotal length of the tile in millimetres (mm); lTtotal width of the tile in millimetres (mm); LAmeasurement base in longitudinal direction in millimetres (mm); LBmeasurement base in transverse direction in millimetres (mm); E1distance between the internal edges of an over - and u
26、nder- tile at one of its extremities in millimetres (mm); E2distance between the internal edges of an over - and under- tile at the other extremity in millimetres (mm). DIN EN 1024:2012-06 EN 1024:2012 (E) 5 4 Test pieces The measurement of geometric characteristics are carried out on 10 test pieces
27、, each of which constitutes a whole tile, except for the measurement of cover dimensions, which requires 24 tiles. 5 Tests methods 5.1 Determination of dimensional characteristics 5.1.1 Individual dimensions1)5.1.1.1 Apparatus The tests are made with a measuring apparatus with a precision of at leas
28、t one millimetre. 5.1.1.2 Procedure After removing any surplus clay from the edges, the measurements shall be taken, both transversely and longitudinally along the centre of the tile unless another measuring position has been specified by the manufacturer (see Figure 1). The dimensions are expressed
29、 to the nearest whole millimetre. Key 1 tile Figure 1 Principle for measuring individual dimensions 5.1.1.3 Expression of results The arithmetic means of the lengths and widths of the 10 tested tiles and the differences expressed as a percentage of these mean values in relation to the values A and B
30、 declared by the manufacturer shall be calculated and noted in the test report. 1) EN 1304 specifies to which type of tiles these measurements apply. DIN EN 1024:2012-06 EN 1024:2012 (E) 6 5.1.2 Overlap dimensions (margins)1)5.1.2.1 Principle The mean overlap dimensions are determined longitudinally
31、 and transversely. They are measured as indicated in Figure 2. NOTE Certain tile models can only be measured in one direction. Key 1 mean cover length 1.1 open position 1.2 closed position 2 mean cover width 2.1 open position 2.2 closed position Figure 2 Principle for measuring cover dimensions 5.1.
32、2.2 Number of test pieces 24 tiles are required for the measurements. 5.1.2.3 Apparatus The tests are carried out with a measuring apparatus with a precision of at least 1 mm. DIN EN 1024:2012-06 EN 1024:2012 (E) 7 5.1.2.4 Procedure The tiles are laid upside down in two rows on a flat surface, and i
33、nterlocked with one another so as to form a stable unit. Certain types of tiles may require laying the right way up. The tiles are interlocked longitudinally and pulled apart individually to measure the maximum distance between two corresponding points on the first and the eleventh tile, i.e. L1, th
34、e maximum length. Following this, the tiles are taken up, then relaid and interlocked. They are pushed together individually as closely as possible to carry out the measurement of the minimum distance (L2) following the procedure described above. Take again the same measurements, but this time, tran
35、sversely in order to obtain the values l1and l2. With regard to tiles with a variable overlap, determine only the measurement of cover in the open position, L1(longitudinally), l1(transversely). NOTE This method is not relevant to some types of tiles designed to be laid broken jointed. 5.1.2.5 Expre
36、ssion of results The mean cover length (L) is obtained from the following formula: L = (L1+L2) / 20 (1) The maximum cover length (LM) (tiles with a variable overlap) is obtained from the following formula: LM= L1/ 10 (2) The mean cover width (l) is calculated from the following formula: l = (l1 + l2
37、) / 20 (3) The maximum cover width (lM) (of tiles with a variable overlap) is calculated from the following formula: lM= l1/ 10 (4) The calculated values as recorded are rounded to the nearest whole millimetre. The percentage difference of these cover dimensions compared with those declared by the m
38、anufacturer are calculated and stated in the test report. 5.2 Cambers 5.2.1 Principle Measure height of camber longitudinally and transversely for plain tiles (see Figures 3, 4 and 5) and longitudinally only for all other types of tile (see Figures 6, 7 and 8). The height of camber for a curvature w
39、hose concavity is located on the outer surface of the tile are given a minus sign and a plus sign is given in the opposite case. The measurement is taken to a precision of at least 0,5 mm on each outside edge of the tile, with the most unfavourable value being selected. Take as measurement bases LAa
40、nd LBequal to2/3 of the total length (LT) and width (lT) of the tile. Where this is not possible, the measurement base may be reduced to the largest dimension that is compatible with the shape of the tile. DIN EN 1024:2012-06 EN 1024:2012 (E) 8 Key 1 dial gauge 2 rule 3 metal plate 4 tile Figure 3 M
41、easurement of longitudinal camber on a plain tile Key 1 dial gauge 2 rule 3 metal plate 4 tile Figure 4 Measurement of longitudinal camber on an ornamental plain tile DIN EN 1024:2012-06 EN 1024:2012 (E) 9 Key 1 dial gauge 2 metal plate 3 tile Figure 5 Measurement of transverse camber on a plain til
42、e Key 1 dial gauge 2 metal plate 3 tile Figure 6 Measurement of longitudinal camber on a tile with sidelock and headlock or a tile with sidelock only DIN EN 1024:2012-06 EN 1024:2012 (E) 10 Key 1 dial gauge 2 metal plate 3 tile Figure 7 Measurement of longitudinal camber on a tile with sidelock and
43、headlock or a tile with sidelock only (reverse side of tile) Key 1 dial gauge 2 metal plate 3 tile Figure 8 Measurement of longitudinal camber on an under-and-over tile DIN EN 1024:2012-06 EN 1024:2012 (E) 11 5.2.2 Apparatus (Figure 9) The measurement is taken using a rule with three contact points,
44、 combined with a device to measure the height of camber accurately to a precision of at least 0,5 mm. Key 1 dial gauge 2 rule 3 contact points Figure 9 Apparatus for measuring cambers The two outer contact points on the rule shall be able to slide so as to adjust to different measurement lengths. An
45、y suitable apparatus may be used to obtain these measurements provided the prescribed requirements are met. 5.2.3 Procedure 5.2.3.1 Longitudinal measurement 5.2.3.1.1 Plain tiles and overlapping tiles The measurement is taken on the exterior face of the tile along the two longitudinal outer edges. 5
46、.2.3.1.2 Tiles with sidelock and headlock, and tiles with sidelock only The measurement is taken on the outer surface of the tile in the bottom of the interlock groove, as well as on the lower edge of the flange which locks into this groove. 5.2.3.1.3 Over-and-under tiles This measurement is taken a
47、long the axis in the bottom of the concavity of the tile, or for tiles with a flat bottom, along the centre line. 5.2.3.2 Transverse measurement - Plain tiles The measurement is taken on the exterior face of the tile along the two transverse - upper and lower - outer edges. (For tiles whose lower ed
48、ge is not a straight line, take the measurement at the widest point of the tile, as far as possible towards the lower edge). DIN EN 1024:2012-06 EN 1024:2012 (E) 12 5.2.4 Expression of results Cambers are obtained from the following formulas: R = h x 100 / LAin percentage, longitudinally (5) R = h x 100 / LBin percentage, transversely (6) where h = hm- hd in absolute value; hmis the measured height of camber in millimetres; hdis the nominal height of camber declared by the ma
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1