DIN EN 10303-2016 Thin magnetic steel strip and sheet for use at medium frequencies German version EN 10303 2015《中等使用频率的薄磁性钢片材和带材 德文版本EN 10303-2015》.pdf

1、February 2016 English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 77.140.40; 77.140.50!%LSO“24148

2、44www.din.deDIN EN 10303Thin magnetic steel strip and sheet for use at medium frequencies;English version EN 10303:2015,English translation of DIN EN 10303:2016-02Dnnes Elektroband und -blech aus Stahl zur Verwendung bei mittleren Frequenzen;Englische Fassung EN 10303:2015,Englische bersetzung von D

3、IN EN 10303:2016-02Bandes et tles extra-minces en acier lectrique pour utilisation moyennes frquences;Version anglaise EN 10303:2015,Traduction anglaise de DIN EN 10303:2016-02SupersedesDIN EN 10303:2001-07www.beuth.deDocument comprises 25 pagesDTranslation by DIN-Sprachendienst.In case of doubt, th

4、e German-language original shall be considered authoritative.03.16 DIN EN 10303:2016-02 2 A comma is used as the decimal marker. National foreword This document (EN 10303:2015) has been prepared by Technical Committee ECISS/TC 108 “Steel sheet and strip for electrical applications” (Secretariat: DIN

5、, Germany) of the European Committee for Iron and Steel Standardization (ECISS). The responsible German bodies involved in its preparation were DIN-Normenausschuss Eisen und Stahl (DIN Standards Committee Iron and Steel) and the DKE Deutsche Kommission Elektrotechnik Elektronik Informationstechnik i

6、m DIN und VDE (German Commission for Electrical, Electronic and Information Technologies of DIN and VDE), Joint Working Committee NA 021-00-07 GA Elektroblech. Amendments This standard differs from DIN EN 10303:2001-07 as follows: a) the scope of the standard has been extended to include grain-orien

7、ted magnetic steel strip and sheet with a nominal thickness of 0,18 mm, and non-oriented magnetic steel strip and sheet with nominal thicknesses of 0,25 mm, 0,27 mm, 0,30 mm, and 0,35 mm; b) the tables have been extended accordingly; c) normative references have been updated; d) the terminology used

8、 has been harmonized with EN 10106 and EN 10107; e) the requirements for the surface condition have been subjected to revision and harmonized with EN 10106 (see 7.4); f) Tables 1 and 2 containing specifications for the magnetic and technological characteristics have been completely revised; g) Subcl

9、ause 6.1 “Mandatory information” has been added; h) Subclauses 7.2 and 7.3 dealing with delivery conditions have been updated; i) thickness tolerances are now given for grain-oriented and for non-oriented steel products; j) the specifications for the width tolerances have been revised (see 8.3.3); k

10、) in Subclause 9.3.1, Table 6 with information on the preparation of specimens for testing magnetic characteristics has been deleted; l) the specifications in Subclause 9.3.1 have been generally revised; m) Annexes A, B, C and D have been included; n) the standard has been editorially revised. Previ

11、ous editions DIN EN 10303: 2001-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10303 October 2015 ICS 77.140.40; 77.140.50 Supersedes EN 10303:2001English Version Thin magnetic steel strip and sheet for use at medium frequencies Bandes et tles extra-minces en acier lectrique pour utilisatio

12、n moyennes frquences Dnnes Elektroband und -blech aus Stahl zur Verwendung bei mittleren Frequenzen This European Standard was approved by CEN on 29 August 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard

13、 the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, F

14、rench, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgar

15、ia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turk

16、ey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. R

17、ef. No. EN 10303:2015 EEN 10303:2015 (E) 2 Contents Page European foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Classification . 6 5 Designation 6 6 Information to be supplied by purchaser. 6 6.1 Mandatory information 6 6.2 Options 7 7 General requirements . 7 7.1 Pro

18、duction process . 7 7.2 Form of supply 7 7.3 Delivery condition 7 7.4 Surface condition 8 7.5 Suitability for cutting . 8 8 Technical requirements 8 8.1 Magnetic properties . 8 8.1.1 Magnetic polarization 8 8.1.2 Specific total loss . 8 8.2 Mechanical properties at room temperature for non-oriented

19、products . 10 8.3 Geometric characteristics and tolerances 10 8.3.1 Thickness of grain-oriented steel products 10 8.3.2 Thickness of non-oriented steel products 11 8.3.3 Width 12 8.3.4 Edge camber . 12 8.3.5 Residual curvature 13 8.3.6 Burr height . 13 8.4 Technological characteristics 13 8.4.1 Dens

20、ity . 13 8.4.2 Stacking factor . 13 8.4.3 Number of bends 13 8.4.4 Insulation coating resistance . 13 9 Inspection . 13 9.1 General . 13 9.2 Selection of samples 14 9.3 Preparation of test specimens . 14 9.3.1 Magnetic properties 14 9.3.2 Mechanical properties 15 9.3.3 Geometrical characteristics an

21、d tolerances . 15 9.3.4 Technological characteristics 15 9.4 Test methods . 15 9.4.1 General . 15 9.4.2 Magnetic properties 15 DIN EN 10303:2016-02 EN 10303:2015 (E) 3 9.4.3 Mechanical properties 16 9.4.4 Geometrical characteristics and tolerances . 16 9.4.5 Technological characteristics 16 9.4.6 Re

22、tests 17 10 Marking, labelling and packaging . 17 11 Complaints 17 Annex A (informative) Minimum stacking factor for non-oriented coated products . 18 Annex B (informative) Maximum specific total loss at 1,0T and 700 Hz and at 1,5T and 400Hz for non-oriented products . 19 Annex C (informative) Densi

23、ty determination 20 Annex D (informative) Mechanical properties for non-oriented products 21 Annex E (informative) Changes to the previous version EN 10303:2001 . 22 Bibliography . 23 DIN EN 10303:2016-02 EN 10303:2015 (E) 4 European foreword This document (EN 10303:2015) has been prepared by Techni

24、cal Committee ECISS/TC 108 “Steel sheet and strip for electrical applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2016, and conflicting

25、 national standards shall be withdrawn at the latest by April 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supe

26、rsedes EN 10303:2001. Regarding the changes that were made in this new edition of EN 10303, see Annex E. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croat

27、ia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and th

28、e United Kingdom. DIN EN 10303:2016-02 EN 10303:2015 (E) 5 1 Scope This European Standard defines the grades of thin non-oriented magnetic steel strip and sheet in nominal thicknesses of 0,05 mm, 0,10 mm, 0,15 mm, 0,20 mm, 0,25 mm, 0,27 mm, 0,30 mm and 0,35 mm, and of thin grain-oriented magnetic st

29、eel strip and sheet in nominal thicknesses of 0,05 mm, 0,10 mm, 0,15 mm and 0,18 mm. In particular, it gives general requirements, magnetic properties, geometric characteristics and tolerances and technological characteristics, as well as inspection procedure. This European Standard applies to magne

30、tic steel strip and sheet supplied in the finally annealed condition in coils and intended for the construction of magnetic circuits used at frequencies equal to or higher than 100 Hz. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document an

31、d are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10204, Metallic products Type

32、s of inspection documents EN 10251, Magnetic materials Methods of determination of the geometrical characteristics of electrical steel sheet and strip EN 60404-2, Magnetic materials Part 2: Methods of measurement of the magnetic properties of electrical steel strip and sheet by means of an Epstein f

33、rame (IEC 60404-2) EN 60404-13, Magnetic materials Part 13: Methods of measurement of density, resistivity and stacking factor of electrical steel sheet and strip (IEC 60404-13) EN ISO 377, Steel and steel products Location and preparation of samples and test pieces for mechanical testing (ISO 377)

34、EN ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1) EN ISO 7799, Metallic materials Sheet and strip 3 mm thick or less Reverse bend test (ISO 7799) IEC 60050-121, International Electrotechnical Vocabulary Chapter 121: Electromagnetism IEC 60050-2

35、21, International Electrotechnical Vocabulary Chapter 221: Magnetic materials and components IEC 60404-10, Magnetic materials Part 10: Methods of measurement of magnetic properties of magnetic sheet and strip at medium frequencies 3 Terms and definitions For the purposes of this document, the terms

36、and definitions given in IEC 60050-121, IEC 60050-221 and the following apply. DIN EN 10303:2016-02 EN 10303:2015 (E) 6 3.1 number of bends number of alternate bends possible before the appearance of the first crack in the base metal visible to the naked eye indicating the ductility of the material

37、3.2 edge camber greatest distance between a longitudinal edge of the sheet and the line joining the two extremities of the measured length of this edge 4 Classification The grades covered by this European Standard are classified according to the maximum value of the specific total loss, in watts per

38、 kilogram, and according to the nominal thickness of the material (0,05 mm; 0,10 mm; 0,15 mm; 0,20 mm; 0,25 mm, 0,27 mm, 0,30 mm and 0,35 mm for non-oriented steel, respectively 0,05 mm; 0,10 mm, 0,15 mm and 0,18 mm for grain-oriented steel). 5 Designation The conventional designation of the differe

39、nt grades comprises the following in the order: a) the characteristic letters: 1) NO for non-oriented strip and sheet; 2) GO for grain-oriented strip and sheet; b) 100 times the nominal thickness of the material, in millimetres; EXAMPLE NO 20: non-oriented strip in thickness of 0,20 mm. c) maximum s

40、pecific total loss by given frequency in cases where steel grades with different values for maximum specific total loss per nominal thickness are stated (see Table 2). 6 Information to be supplied by purchaser 6.1 Mandatory information For material to comply adequately with the requirements of this

41、standard, the purchaser shall include the following information in his enquiry or order: a) the quantity required (including any limitations on the mass of a coil) (see 7.2); b) type of product (strip or sheet); c) number of this European Standard (EN 10303); d) the grade designation of the material

42、, in accordance with Clause 5; e) the dimensions of strips required (including any limitations of the internal and external diameter of a coil) (see 7.2 and 8.3.2); f) the inspection procedure required including the nature of the related documents (see 9.1); DIN EN 10303:2016-02 EN 10303:2015 (E) 7

43、6.2 Options A number of options are specified in this standard and listed below. lf the purchaser does not indicate his wish to implement one of these options, the products shall be supplied in accordance with the basis specification of this standard (see 6.1): 1) presence of welds or interleaves an

44、d their optional marking (see 7.2); 2) compatibility of the surface insulation coating (see 7.4); 3) residual curvature (see 8.3.5); 4) insulation coating resistance (see 8.4.4). 5) mechanical properties for non-oriented products (see Table D.1) 7 General requirements 7.1 Production process The prod

45、uction process of the steel and its composition are left to the discretion of the manufacturer. 7.2 Form of supply The material is supplied in coils. The mass of coils shall be agreed at the time of ordering. The recommended value for the internal diameter of coils is approximately 400 mm except for

46、 non-oriented strip in thickness of 0,20 mm; 0,25 mm, 0,27 mm, 0,30 mm and 0,35 mm, and grain-oriented strip in thickness of 0,18 mm for which the recommended internal diameter is approximately 500 mm. The strip shall be of constant width and wound in such a manner that the edges are super-imposed i

47、n a regular manner and that the side faces of the coil are substantially flat. The coils shall be sufficiently tightly wound that they do not collapse under their own weight. The strip can occasionally exhibit welds or interleaves resulting from the removal of defective zones, subject to prior agree

48、ment between the parties. The value of the additional thickness due to the weld is subject to the agreement. If necessary the marking of welds or interleaves may form the subject of a special agreement. For coils containing repair welds or interleaves, each part of the strip shall be of the same gra

49、de material. The edges of parts welded together shall not be so much out of alignment as to affect the further processing of the material. 7.3 Delivery condition Products according to this standard are delivered either with a coating on one or on both sides but also without coating. Different types of coating can be provided. DIN EN 10303:2016-02 EN 10303:2015 (E) 8 7.4 Surface condition The surfaces shall be smooth and clean and free from grease and rust.1)Dispersed