DIN EN 10339-2007 Steel tubes for onshore and offshore water pipelines - Internal liquid applied epoxy linings for corrosion protection English version of DIN EN 10339 2007-05《陆上和海.pdf

1、May 2007DEUTSCHE NORM English price group 9No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.040.99; 25.220.60!,x4“98

2、51795www.din.deDDIN EN 10339Steel tubes for onshore and offshore water pipelines Internal liquid applied epoxy linings for corrosion protectionEnglish version of DIN EN 10339:2007-05Stahlrohre fr erd- und wasserverlegte Wasserleitungssysteme Innenauskleidung mit Epoxidharzen als KorrosionsschutzEngl

3、ische Fassung DIN EN 10339:2007-05www.beuth.deDocument comprises 18 pages 08.07DIN EN 10339:2007-05 2 National foreword This standard has been prepared by ECISS/TC 29 “Steel tubes and fittings for steel tubes” (Secretariat: UNI, Italy). The responsible German body involved in its preparation was the

4、 Normenausschuss Gastechnik (Gas Technology Standards Committee), Technical Committee 5.2 Auenkorrosion. For steel tubes complying with this standard, adequate corrosion protection in the weld zone is not ensured and infiltration of liquid is to be expected. Therefore, such tubes are not used for th

5、e transport and distribution of water intended for human consumption. Because the lining materials used are subjected to additional hygiene requirements, the possibilities of subsequently lining the tubes in the weld zone are limited, especially for tubes with small diameters. Curing epoxy resin as

6、specified here is problematic on site, since an incomplete epoxy polymerisation process may result in organic substances becoming bioavailable. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10339February 2007ICS 23.040.99; 25.220.60English VersionSteel tubes for onshore and offshore water pipeli

7、nes - Internalliquid applied epoxy linings for corrosion protectionTubes pour canalisations deau enterres et immerges -Revtements internes en rsine poxyde applique ltatliquide pour la protection contre la corrosionStahlrohre fr erd- und wasserverlegteWasserleitungssysteme - Innenauskleidung mitEpoxi

8、dharzen als KorrosionsschutzThis European Standard was approved by CEN on 20 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date li

9、sts and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the respo

10、nsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Icela

11、nd, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stass

12、art, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10339:2007: EEN 10339:2007 (E) 2 Contents Page 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Symbols and abbreviations 5 5 Lining material

13、s .5 5.1 General5 5.2 Technical specification .5 5.3 Packaging .8 6 Information to be supplied by the purchaser .8 6.1 Mandatory.8 6.2 Options to be indicated by the purchaser.8 7 Surface preparation and application of the lining8 7.1 Surface preparation.8 7.2 Application of the lining9 8 Requiremen

14、ts of the applied lining10 8.1 General10 8.2 Appearance and continuity.10 8.3 Minimum dry film thickness of the lining10 8.4 Hardness measured by Buchholz indentation .11 8.5 Non porosity.11 8.6 Adhesion.11 8.7 Cut back lengths11 8.8 Summary of the required properties .12 9 Repairs12 10 Marking .13

15、11 Handling, transportation and storage13 11.1 Handling and transportation to the storage area .13 11.2 Storage13 11.3 Loading of tubes for delivery .13 Annex A (normative) Adhesion test - Resistance to removal .14 A.1 General14 A.2 Apparatus .14 A.3 Procedure .14 A.4 Results 15 Bibliography 16 EN 1

16、0339:2007 (E) 3 Foreword This document (EN 10339:2007) has been prepared by Technical Committee ECISS/TC 29 “Steel tubes and fittings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identi

17、cal text or by endorsement, at the latest by August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standa

18、rd: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10

19、339:2007 (E) 4 1 Scope This European Standard specifies the requirements for the application of liquid applied epoxy internal linings, for the corrosion protection of steel tubes. This type of lining is generally used in the transport and distribution, under pressure or by gravity, of water intended

20、 for human consumption and industrial use, sea water, waste water and also in fire water. The temperature of the water transported generally does not exceed 50 C. The choice of the lining and its limits of use depend on the type of product used, the pipe laying conditions, the temperature and the ch

21、emical composition of the fluid. The choice of the product for the medium to be transported and its qualification are not part of this European Standard. The lining consists normally of one layer of liquid product, applied by spray airless technique after surface preparation. All or some of the requ

22、irements of this European Standard can apply to the internal linings of fittings, if agreed by the purchaser and the coater. The lining in this European Standard can be applied to longitudinally or spirally welded tubes and to seamless steel tubes used for the construction of pipelines for conveying

23、 liquids. These tubes are not intended to be bent after the epoxy lining has been applied. This European Standard does not cover in-situ applied or rehabilitation linings. The constituent materials of epoxy linings, when used under the conditions for which they are designed, in permanent or temporar

24、y contact with water intended for human consumption, should not change the quality of that water to such an extent that it fails to comply with the requirements of European regulations at the end user. For this purpose, reference should be made to the relevant national standards transposing EN stand

25、ards when available, dealing with the influence of materials on water quality. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the ref

26、erenced document (including any amendments) applies. EN 1184, Materials and articles in contact with foodstuffs Test methods for translucency of ceramic articles EN ISO 2808, Paints and varnishes Determination of film thickness (ISO 2808:1997) EN ISO 2811-1, Paints and varnishes Determination of den

27、sity Part 1: Pyknometer method (ISO 2811-1:1997) EN ISO 2815, Paints and varnishes Buchholz indentation test (ISO 2815:2003) EN ISO 3251, Paints, varnishes and plastics Determination of non-volatile-matter content (ISO 3251:2003) EN ISO 4287, Geometrical product specification (GPS) Surface texture:

28、Profile method Terms, definitions and surface texture parameters (ISO 4287:1997) EN ISO 4624, Paints and varnishes Pull-off test for adhesion (ISO 4624:2002) EN 10339:2007 (E) 5 EN ISO 8501-1, Preparation of steel substrates before application of paints and related products Visual assessment of surf

29、ace cleanliness Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:1988) EN ISO 8503-2, Preparation of steel substrates before application of paints and related products Surface roughness characterist

30、ics of blast-cleaned steel substrates Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel Comparator procedure (ISO 8503-2:1988) EN ISO 8503-4, Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-c

31、leaned steel substrates Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile Stylus instrument procedure (ISO 8503-4:1988) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 product m

32、anufacturer supplier of the epoxy materials in a condition suitable for application to the product to be coated 3.2 coater company responsible for applying the lining material to the components to be coated 3.3 purchaser company that buys the coated tubes and fittings 4 Symbols and abbreviations For

33、 the purposes of this document, the following symbol applies. Rzthe average roughness from five successive evaluation areas defined according to EN ISO 4287, expressed in microns (m) 5 Lining materials 5.1 General The lining material is generally composed of a base (epoxy resin) and a curing agent.

34、A primer may be used when recommended by the product manufacturer. The base (epoxy resin) and curing agent should have different colours allowing the verification of the correct mixing by checking the uniformity of the colour of the mixed product. This European Standard calls for the use of substanc

35、es and/or procedures that may be injurious to health if precautions are not taken. It refers only to technical suitability and in no way absolves the user from statutory obligations relating to health and safety at any stage. 5.2 Technical specification The technical specification drawn up by the pr

36、oduct manufacturer shall contain as a minimum the information detailed in Table 1. Where testing standards are mentioned in Table 1, the data supplied by the product EN 10339:2007 (E) 6 manufacturer shall be according to these standards. Otherwise, test methods shall be given for any test detailed i

37、n Table 1. Tests shall be done to be consistent with the product manufacturers recommendations for application. Infrared scan of the product components shall be made available on request to the coater. Other data or tests can be agreed between the parties at the time of enquiry and/or order. If test

38、 certificates are required, they shall at least contain the data mentioned in Table 1. EN 10339:2007 (E) 7 Table 1 Contents of Technical data sheet and Test certificates Elements Technical data sheets Test certificatesDate of issue x x Name of manufacturer x x Field of application x Name and type of

39、 product x x Type of base (epoxy resin) x Type of curing agent x Factory of origin x Batch or production lot number xaUse by date xaColour xaMethods of application x Solids by volume x Solids by weight of the mixed product according EN ISO 3251 xbTheoretical coverage per m for nominal thickness x Sh

40、elf life xaStorage conditions x Pot-life x Surface preparation x Recommended instructions for application x Recommended repair method(s) x Mixing instructions (induction time if applicable) x Recommended dry film thickness (nominal and range) x Maximum recommended dry film thickness applicable in on

41、e layer x Minimum and maximum overcoating time x Range of application temperature (ambient, tube and product) and humidity x Specific curing requirements x Hardness measured by Buchholz indentation test according to EN ISO 2815 of cured lining measured x Time related to curing temperature to achieve

42、 the full curing x Viscosity x x cdDensity according to EN ISO 2811-1 x d ex aElongation at break on free film according to EN 1184 x Pull-off test for adhesion according to EN ISO 4624 x a Required for the base (epoxy resin) and curing agents. b In contradiction to the curing cycle specified in EN

43、ISO 3251, curing cycle of 2 days at 23 C 2 C will apply. c Required for the base (epoxy resin), curing agent and the mixed product. d The acceptable limits shall be mentioned in the test certificate. e Required for the base (epoxy resin), curing agent. For the mixed product, density can be calculate

44、d. EN 10339:2007 (E) 8 5.3 Packaging As a minimum requirement, all materials supplied for lining operations shall be suitably marked with the following details: the product manufacturers name; the name of the material; the batch number; the use-by date; the recommended storage conditions; the colour

45、 of the material. 6 Information to be supplied by the purchaser 6.1 Mandatory The purchaser shall state in his enquiry and order the following minimum information: Tubes and fittings to be coated according to this European Standard. These shall be designated by reference to this European Standard. I

46、f applicable, the reference to the standard for the tube to which the lining is applied shall be added to this designation. EXAMPLE: 5 000 m of tube - EN 10224 of 406, 4-4, 0 Internal lining EN 10339; type of fluid to be transported; minimum dry film thickness of the lining (see 8.3); service temper

47、ature; 6.2 Options to be indicated by the purchaser Maximum number and dimensions of repairs (not including repairs due to destructive tests); cut back lengths (see 8.7). 7 Surface preparation and application of the lining 7.1 Surface preparation 7.1.1 Prior to abrasive blast cleaning, the steel sur

48、face shall be dry and free from contamination (oil, grease, temporary corrosion protection etc.) and surface defects (slivers, laminations etc.) detrimental to the surface or to the adhesion of the lining. 7.1.2 Tubes shall be abrasive blast cleaned. The degree of cleanliness shall be at least Sa 2,

49、5 when examined according to EN ISO 8501-1. EN 10339:2007 (E) 9 Unless otherwise recommended by the manufacturer of the product, the blast cleaned surface shall have a roughness Rz, as defined in EN ISO 4287 between 50 m and 90 m, as measured according to EN ISO 8503-4. Grading of the surface can also be examined according to EN ISO 8503-2, the profile grade shall be “medium”. 7.1.3 After blast cleaning, the surface of the components shall be visually inspected. All slivers, laminations, weld s