DIN EN 1036-2-2008 Glass in building - Mirrors from silver-coated float glass for internal use - Part 2 Evaluation of conformity - Product standard English version of DIN EN 1036-2.pdf

1、May 2008DEUTSCHE NORM English price group 15No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 81.040.20!$Nr0“1437913www.

2、din.deDDIN EN 1036-2Glass in building Mirrors from silver-coated float glass for internal use Part 2: Evaluation of conformity Product standardEnglish version of DIN EN 1036-2:2008-05Glas im Bauwesen Spiegel aus silberbeschichtetem Floatglas fr den Innenbereich Teil 2: Konformittsbewertung Produktno

3、rmEnglische Fassung DIN EN 1036-2:2008-05www.beuth.deDocument comprises 36 pagesDIN EN 1036-2:2008-05 2 Start of validity This standard is due to be valid from 1 November 2008. It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard ha

4、s been listed in the Bundesanzeiger (German Federal Law Gazette) and from the date given therein. National foreword This standard has been prepared by Technical Committee CEN/TC 129 “Glass in building” (Secretariat: NBN, Belgium), Working Group WG 1 “Basic glass products” (Secretariat: AFNOR, France

5、). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committee NA 005-09-29 AA Glas im Bauwesen (Sp CEN/TC 129 und ISO/TC 160). The European Standards referred to in clause 2 of this document have

6、been published as the corresponding DIN EN or DIN EN ISO Standards with the same number. EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1036-2 February 2008 ICS 81.040.20 English Version Glass in building - Mirrors from silver-coated float glass for internal use - Part 2: Evaluation of conform

7、ity - Product standardVerre dans la construction - Miroirs en glace argente pour lintrieur - Partie 2: Evaluation de la conformit - Norme de produit Glas im Bauwesen - Spiegel aus silberbeschichtetem Floatglas fr den Innenbereich - Teil 2: Konformittsbewertung - Produktnorm This European Standard wa

8、s approved by CEN on 29 December 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such

9、national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language

10、and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembo

11、urg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All righ

12、ts of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1036-2:2008: E2 Contents Page Foreword. 4 1 Scope 5 2 Normative references . 5 3 Terms and definitions. 6 4 Requirements 6 4.1 Product description 6 4.2 Conformity with the definition of mirror.

13、7 4.3 Determination of the characteristics performances. 7 4.3.1 Characteristics of mirror 7 4.3.2 Determination of characteristics of mirrors. 8 4.4 Durability 9 4.5 Dangerous substances. 10 5 Evaluation of conformity 10 5.1 General. 10 5.2 Initial type testing of the product (see 5.1, 2) . 10 5.2.

14、1 General. 10 5.2.2 Initial type testing of mirror . 12 5.2.3 Initial type testing of characteristics performances. 13 5.3 Factory production control and inspection of samples in accordance with a prescribed test plan (see 5.1, 1) a). 13 5.4 Initial inspection of factory and of factory production co

15、ntrol (see 5.1, 1) b). 14 5.5 Continuous surveillance and assessment of the factory production control (see 5.1, 1) c). 15 6 Marking and/or labelling. 15 6.1 General. 15 6.2 Product marking 15 6.3 Product characteristics 15 6.4 “Characteristics/performance identification paper” . 15 Annex A (normati

16、ve) Factory Production Control (FPC) 17 A.1 Factory Production Control (FPC) requirements. 17 A.1.1 General. 17 A.1.2 Organisation 17 A.1.3 Control system 17 A.2 Marking 18 A.3 Inspection and testing tables of mirror production 18 A.3.1 Information in Table A.1 . 18 A.3.2 Production control 19 A.3.3

17、 Product control . 19 A.3.4 Use of proxy testing 19 Annex B (informative) Tests for ensuring conformity during factory production control 22 B.1 Information on ensuring durability conformity 22 B.2 Dip test . 22 B.2.1 General. 22 B.2.2 Test method. 22 B.2.3 Acceptance criteria. 22 Annex C (informati

18、ve) Provisions for voluntary involvement of third party(ies). 23 C.1 General. 23 DIN EN 1036-2:2008-05 EN 1036-2:2008 (E) 3 C.2 Voluntary tasks for third parties 23 C.3 Marking and labelling . 23 Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU Construction Pr

19、oducts Directive. 24 ZA.1 Scope and relevant characteristics. 24 ZA.2 Procedure(s) for the attestation of conformity of mirror products 26 ZA.2.1 System(s) of attestation of conformity . 26 ZA.2.2 EC Certificate and Declaration of conformity 29 ZA.3 CE marking and labelling . 31 Bibliography . 34 DI

20、N EN 1036-2:2008-05 EN 1036-2:2008 (E)4 Foreword This document (EN 1036-2:2008) has been prepared by Technical Committee CEN/TC 129 “Glass in building”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an ident

21、ical text or by endorsement, at the latest by August 2008, and conflicting national standards shall be withdrawn at the latest by August 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held re

22、sponsible for identifying any or all such patent rights. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Ann

23、ex ZA which is an integral part of this document. EN 1036 Glass in building Mirrors from silver-coated float glass for internal use consists of the following parts: Part 1: Definition, requirements and test methods Part 2: Evaluation of conformity; product standard According to the CEN/CENELEC Inter

24、nal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal

25、ta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 1036-2:2008-05 EN 1036-2:2008 (E) 5 1 Scope This European Standard specifies requirements, the evaluation of conformity and the factory production control of flat mirrors

26、 from silver-coated float glass for internal use in buildings. NOTE For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply. 2 Normative references The following referenced documents are indispensable for t

27、he application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 356, Glass in building Security glazing Testing and classification of resistance against manual attack E

28、N 410, Glass in building Determination of luminous and solar characteristics of glazing EN 572-1, Glass in building Basic soda lime silicate glass products Part 1: Definition and general physical and mechanical properties EN 572-2, Glass in building Basic soda lime silicate glass products Part 2: Fl

29、oat glass EN 572-8, Glass in building Basic soda lime silicate glass products Part 8: Supplied and final cut sizes EN 673, Glass in building Determination of thermal transmittance (U value) Calculation method EN 1036-1:2007, Glass in building Mirrors from silver-coated float glass for internal use P

30、art 1: Definitions, requirements and test methods EN 1063, Glass in building Security glazing Testing and classification of resistance against bullet attack EN 12600, Glass in building Pendulum test Impact test method and classification for flat glass EN 12758, Glass in building Glazing and airborne

31、 sound insulation Product descriptions and determination of properties EN 12898, Glass in building Determination of the emissivity EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 13501-2, Fire classificat

32、ion of construction products and building elements Part 2: Classification using data from fire resistance tests, excluding ventilation services EN 13501-5, Fire classification of construction products and building elements Part 5: Classification using data from external fire exposure to roofs tests

33、EN 13541, Glass in building Security glazing Testing and classification of resistance against explosion pressure DIN EN 1036-2:2008-05 EN 1036-2:2008 (E)6 3 Terms and definitions For the purpose of this document, the terms and definitions given in EN 1036-1:2007 and the following apply. 3.1 Initial

34、Type Testing (ITT) determination of the performance of a product (characteristic, durability), on the basis of either actual tests or other procedures (such as conventional, standardised, tabulated or general accepted values, standardised or recognised calculation methods, test reports when made ava

35、ilable,), in accordance with this European Standard that demonstrates compliance with this European Standard 3.2 test report document that covers the results of tests undertaken on a representative sample of the product from production or on a prototype design of the product 3.3 product description

36、document that details the relevant parameters, e.g. process conditions, structure, for defining a product that complies with the standard. It includes specific reference(s) to characteristics that are modified by the production process 3.4 significant change variation in performance beyond the permi

37、tted tolerance for the characteristic 4 Requirements 4.1 Product description For conformity purposes the mirror manufacturer is responsible for the preparation and maintenance of the product description. This description shall describe the product and/or product families. Disclosure of the product d

38、escription shall be at the discretion of the mirror manufacturer or his agent except in the case of regulatory requirements. The description shall contain at least a normative part. The description may also contain an informative part, when the manufacturer foresees further development of the produc

39、t. The normative part of the description shall contain the following information: reference to EN 1036-1 and -2 and all other standards with which the manufacturer claims compliance; materials making up the layers of the mirror; glass substrates. The layers may be listed either in full, i.e. chemica

40、l composition, or by manufacturers code. The substitution of materials shall maintain the conformity with the product description. The substituting material can be added to the product description when compliance has been demonstrated. DIN EN 1036-2:2008-05 EN 1036-2:2008 (E) 7 4.2 Conformity with t

41、he definition of mirror Products shall conform to the definition and fulfil the requirements of mirror as defined in EN 1036-1. 4.3 Determination of the characteristics performances 4.3.1 Characteristics of mirror 4.3.1.1 General The characteristics of mirror are in general those of the glass substr

42、ate (see 4.3.1.2). 4.3.1.2 Characteristics of the soda lime silicate glass panes used for the production of mirrors Panes shall be made of soda lime silicate float glass according to EN 572-1, EN 572-2, 572-8. For the characteristics listed in Table 1, for the soda lime silicate glass panes, general

43、ly accepted values or calculated values shall be used. Since the mirror production process does not change the majority of the characteristics of Table 1 significantly they shall be used for mirrors. The characteristics that are significantly changed are the light transmittance/reflectance and solar

44、 heat transmittance/reflectance. Table 1 Information on the characteristics of soda lime silicate glass panes, according to EN 572-1, used for the production of mirrors Characteristic Symbol Unit - density - hardness - youngs modulus - poissons ratio - characteristic bending strength - resistance ag

45、ainst sudden temperature changes and temperature differentials - specific heat capacity - coefficient of linear expansion - thermal conductivity (for U-value) - mean refractive index to visible radiation - emissivity - light transmittance - solar direct transmittance - total energy transmittance HK0

46、,1/20 E fg,k c n veg kg/m GPa Pa dimensionless Pa K J/(kgK) K-1W/(mK) dimensionless dimensionless dimensionless dimensionless dimensionless DIN EN 1036-2:2008-05 EN 1036-2:2008 (E)8 4.3.2 Determination of characteristics of mirrors 4.3.2.1 General If the mirror manufacturer wishes to claim that any

47、performance characteristic is independent of the production equipment used then the factory production control system shall be in accordance with this European Standard including his specific process control conditions. NOTE Products complying with the definition from EN 1036-1, are unlikely to be c

48、apable of being classified for the following characteristics: 4.3.2.2; 4.3.2.5; 4.3.2.6; 4.3.2.7; 4.3.2.8. 4.3.2.2 Safety in the case of fire - Resistance to fire Fire resistance shall be determined and classified in accordance with EN 13501-2. NOTE EN 357 can be used as a classification reference s

49、pecific to fire resistant glazed elements. 4.3.2.3 Safety in the case of fire - Reaction to fire Reaction to fire shall be determined and classified in accordance with EN 13501-1. Mirrors, manufactured from silvered float glass, are products/materials that do not require to be tested for reaction to fire (e.g. products/materials of Classes A1 according to Commission Decision 96/603/EC, as amended 2000/605/EC). 4.3.2.4 Safety in the case of fire - External fire behaviour Where the