DIN EN 1113-2015 Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification German version EN 1113 2015《卫浴.pdf

1、June 2015 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 2

2、3.040.70; 91.140.70!%CZm“2325574www.din.deDDIN EN 1113Sanitary tapware Shower hoses for sanitary tapware for water supply systems of type 1and type 2 General technical specification;English version EN 1113:2015,English translation of DIN EN 1113:2015-06Sanitrarmaturen Brauseschluche fr Sanitrarmatur

3、en fr Wasserversorgungssysteme vom Typ 1 undTyp 2 Allgemeine technische Spezifikation;Englische Fassung EN 1113:2015,Englische bersetzung von DIN EN 1113:2015-06Robinetterie sanitaire Flexibles de douches pour robinetterie sanitaire pour les systmes dalimentationtype 1 et type 2 Spcifications techni

4、ques gnrales;Version anglaise EN 1113:2015,Traduction anglaise de DIN EN 1113:2015-06SupersedesDIN EN 1113:2011-05www.beuth.deDocument comprises 25 pagesIn case of doubt, the German-language original shall be considered authoritative.06.15 DIN EN 1113:2015-06 2 A comma is used as the decimal marker.

5、 National foreword This document (EN 1113:2015) has been prepared by Technical Committee CEN/TC 164 “Water supply” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the DIN-Normenausschuss Armaturen (DIN Standards Committee Valves), Working Committee NA 003-02

6、-01 AA Sanitrarmaturen. Amendments This standard differs from DIN EN 1113:2011-05 as follows: a) Amendment A1:2011 has been incorporated; b) 2 classes for hoses for supply systems of type 1 have been introduced, see Table 1 and Table 3. Previous editions DIN EN 1113: 1997-03, 2008-06, 2011-05 DIN EN

7、 13905: 2003-12 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1113 April 2015 ICS 23.040.70; 91.140.70 Supersedes EN 1113:2008+A1:2011English Version Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification Robinetter

8、ie sanitaire - Flexibles de douches pour robinetterie sanitaire pour les systmes dalimentation type 1 et type 2 - Spcifications techniques gnrales Sanitrarmaturen - Brauseschluche fr Sanitrarmaturen fr Wasserversorgungssysteme vom Typ 1 und Typ 2 - Allgemeine technische Spezifikation This European S

9、tandard was approved by CEN on 12 March 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concernin

10、g such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into it

11、s own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germa

12、ny, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR

13、NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1113:2015 EEN 1113:2015 (E) 2 Contents Foreword 4 Introduction .5 1 Scope 6 2 Normative references 9 3 Te

14、rms and definitions .9 4 Designation 9 5 Marking .9 6 Materials .9 6.1 Chemical and hygienic requirements 9 6.2 Exposed surface condition and quality of coating . 10 7 Dimensional characteristics 10 7.1 General . 10 7.2 Connecting dimensions . 10 7.3 Special cases 11 8 Hydraulic characteristics . 11

15、 8.1 General . 11 8.2 Flow rate 12 8.2.1 Test method . 12 8.2.2 Principle . 12 8.2.3 Apparatus 12 8.2.4 Procedure 12 8.2.5 Requirements 12 9 Mechanical and leaktightness characteristics 14 9.1 General . 14 9.2 Tensile strength 14 9.2.1 Test method . 14 9.2.2 Principle . 14 9.2.3 Apparatus 14 9.2.4 P

16、rocedure 15 9.2.5 Requirements 15 9.3 Resistance to flexing 15 9.3.1 Test Method . 15 9.3.2 Principle . 15 9.3.3 Apparatus 15 9.3.4 Procedure 17 9.3.5 Requirement 17 9.4 Pressure resistance at elevated temperature 17 9.4.1 Test method . 17 9.4.2 Principle . 17 9.4.3 Apparatus 18 9.4.4 Procedure 18 9

17、.4.5 Requirements 19 9.5 Leaktightness after tensile strength and resistance to flexing tests 19 9.5.1 Test method . 19 9.5.2 Principle . 19 DIN EN 1113:2015-06 EN 1113:2015 (E) 3 9.5.3 Apparatus . 19 9.5.4 Procedure . 19 9.5.5 Requirements . 19 9.6 Thermal shock test 19 9.6.1 Test method . 19 9.6.2

18、 Principle . 19 9.6.3 Apparatus . 19 9.6.4 Procedure . 20 9.6.5 Requirements . 20 10 Rotary connection . 20 10.1 General . 20 10.2 Test Method . 21 10.2.1 Principle . 21 10.2.2 Apparatus . 21 10.2.3 Procedure . 21 10.2.4 Requirement . 22 Bibliography 23 DIN EN 1113:2015-06 EN 1113:2015 (E) 4 Forewor

19、d This document (EN 1113:2015) has been prepared by Technical Committee CEN/TC 164 “Water supply”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Octobe

20、r 2015, and conflicting national standards shall be withdrawn at the latest by October 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent r

21、ights. This document supersedes EN 1113:2008+A1:2011. The main change to this standard is the introduction of 2 classes for hoses for supply systems of type 1. See Table 1 and Table 3. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries

22、are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

23、Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 1113:2015-06 EN 1113:2015 (E) 5 Introduction In respect of potential adverse effects on the quality of water intended for human consumption caused by the product covered by this European Standard

24、: This European Standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA. While awaiting the adoption of verifiable European criteria, existing national regulations concerning the use and/or the characteristics of this p

25、roduct remain in force. DIN EN 1113:2015-06 EN 1113:2015 (E) 6 1 Scope This European Standard specifies: the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses should comply; the procedures for testing these characteristics. This European Standard applies to

26、 shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers. This European Standard applies to shower hoses connected downstream of the obturator of the tapware. Hoses which are an integral part of sanitary tapware (

27、sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard. Details of pressures and temperatures are given in Table 1. Table 1 Conditions of use/Classifications Water Supply system Operating range of shower hoses

28、Flow rates Limits Recommended See Table 3 Type 1 seeFigure 1Dynamic Pressure (0,05 to 0,5) MPa (0,5 to 5) bar Dynamic Pressure (0,1 to 0,3) MPa (1,0 to 3,0) bar Class 1 0,42 l/s Q (25,2 l/min Q) at (0,0200,3+) MPa (0,203+) bar Class 2 0,20 l/s Q 0,42 l/s (12 l/min Q 25,2 l/min) at (0,0200,3+) MPa (0

29、,203+) bar Type 2 seeFigure 2Dynamic Pressure (0,01 to 0,2) MPa (0,1 to 2) bar Dynamic Pressure (0,02 to 0,10) MPa (0,2 to 1,0) bar Class E 0,06 l/s Q 0,18 l/s (3,6 l/min Q 10,8 l/min.) at (0,000500,01+) MPa (0,00500,1+) bar Class H 0,18 l/s Q (10,8 l/min Q) at (0,000500,01+) MPa (0,00500,1+) bar Te

30、mperature T 70C T 42C DIN EN 1113:2015-06 EN 1113:2015 (E) 7 Key 1 cold water 2 hot Water 3 mains supply pipe (Supply pressures up to 10 bar) 4 water heater Figure 1 Type 1 Water supply system with a pressure range of (0,05 1,0) MPa (0,5 - 10) bar DIN EN 1113:2015-06 EN 1113:2015 (E) 8 Key 1 cold wa

31、ter storage cistern (cover omitted for clarity) 2 warning pipe 3 vent pipe 4 hot water cylinder 5 alternative cistern fed cold supply to sanitary appliances 6 to boiler 7 mains supply pipe (Supply pressures up to 10 bar) Figure 2 Type 2 Water supply system - with a pressure range of (0,01 1,0) MPa,

32、(0,1 - 10) bar. A vented domestic hot water and cold water supply system incorporating gravity hot water, mains cold water and alternative gravity cold water supply to sanitary appliances DIN EN 1113:2015-06 EN 1113:2015 (E) 9 2 Normative references The following documents, in whole or in part, are

33、normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 248, Sanitary tapware General specification for electr

34、odeposited coatings of Ni-Cr EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation (ISO 228-1) 3 Terms and definitions For the purposes of this document, the following term and definition applies. 3.1 shower hose flexible su

35、pply pipe which connects sanitary tapware to a shower handset 4 Designation Hoses complying with this European Standard are designated by: the connecting thread dimensions G 1/2 G 1/2 or G 1/2 G 3/4; reference to this European Standard: EN 1113; the length; the material of the external sheath (plast

36、ic, metal); the type of nuts and if conical the dimension C; flow rate class (see Table 1). EXAMPLE Shower hose G 1/2, cone 26 G 3/4, length 1,5 m, metal sheath, EN 1113, class H. 5 Marking Hoses complying with this European Standard shall be marked permanently and legibly with the manufacturers mar

37、k or the suppliers mark. 6 Materials 6.1 Chemical and hygienic requirements All materials coming into contact with water intended for human consumption shall not present any risk to health at temperatures up to the maximum working temperature. They shall not cause any deterioration to water intended

38、 for human consumption in terms of quality, appearance, smell or taste. DIN EN 1113:2015-06 EN 1113:2015 (E) 10 Within the recommended limit for correct operation (see Table 1) the materials shall not undergo any change which would impair the performance of shower hoses. 6.2 Exposed surface conditio

39、n and quality of coating Visible chromium plated surfaces and Ni-Cr coatings shall comply with the requirements of EN 248. 7 Dimensional characteristics 7.1 General The design and construction of components without defined dimensions permits various design solutions to be adopted by the manufacturer

40、. Permitted deviations from the defined dimensions are specified in 7.3. 7.2 Connecting dimensions The connecting dimensions of shower hoses are specified in Table 2 and Figures 3, 4 and 5. Table 2 Connecting dimensions Dimensions Values Comments A G 1/2 or G 3/4 Connecting thread (tap side) EN ISO

41、228-1 B G 1/2 Connecting thread (shower side) EN ISO 228-1 C 23 5010,+mm or 26 5010,+mm Major diameter of conical nut (if provided) G 8,5 01mm Functional dimension on seal depth I 1,5 500, +mm Thread counterbore K 30 mm Total length of conical nut 301Cone angle (if provided) L 1250 mm Total length o

42、f hose DIN EN 1113:2015-06 EN 1113:2015 (E) 11 Figure 3 Conical nut Figure 4 Nut (shape unspecified) Figure 5 Hose length 7.3 Special cases Shower hoses intended for special applications e.g. when dimensional interchangeability is not a requirement, can incorporate dimensional deviations provided: c

43、onnection to the installation is guaranteed; threaded connections are in compliance with ISO standards; all other requirements of this European Standard are satisfied; the manufacturers literature, including the installation instructions supplied with the shower hose, indicates clearly that the show

44、er hose is a special case. 8 Hydraulic characteristics 8.1 General The test described is a type test (laboratory test) and not a quality control test carried out during manufacture. DIN EN 1113:2015-06 EN 1113:2015 (E) 12 8.2 Flow rate 8.2.1 Test method This clause describes a method for testing the

45、 flow rate of hoses. 8.2.2 Principle The principle consists of a method for measuring the flow rate through the shower hose using cold water (T 30 C) in order to determine the flow rate class (see Table 1). 8.2.3 Apparatus The test apparatus shown in Figure 6, comprises: 1) A supply circuit comprisi

46、ng: a) a means for measuring and maintaining the required pressure of Table 1 with an accuracy of 1 % of the test value; b) a device for measuring the flow rate with an accuracy of 2 % of the test value; c) a DN15 regulating valve; d) a straight DN15 pipe; e) a pressure take off tee (see Figure 7);

47、f) a pressure measuring device with an accuracy of 1 %. 2) A test circuit comprising: a) a support to maintain the hose in a straight and horizontal position. 8.2.4 Procedure Connect the G 1/2 size nut of the shower hose to the pressure take off tee, supporting the hose in a horizontal position. App

48、ly the required dynamic pressure using the horizontal axis of the hose as a datum. Record the flow rate “Q” after stabilization. 8.2.5 Requirements Shower hoses shall be classified according to the flow rate value “Q” at the required pressure shown in Table 3. DIN EN 1113:2015-06 EN 1113:2015 (E) 13 Table 3 Flow rate classes Supply system Flow rate / pressure Of Type 1 Class 1 0,42 l/s Q (25,2 l/min