DIN EN 12158-2-2011 en 2959 Builders- hoists for goods - Part 2 Inclined hoists with non-accessible load carrying devices German version EN 12158-2 2000+A1 2010《货物用建筑提升机 第2部分 带不可达承.pdf

1、April 2011 Translation by DIN-Sprachendienst.English price group 17No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、91.140.90!$nwj“1758471www.din.deDDIN EN 12158-2Builders hoists for goods Part 2: Inclined hoists with non-accessible load carrying devices(includes Amendment A1:2010)English translation of DIN EN 12158-2:2011-04Bauaufzge fr den Materialtransport Teil 2: Schrgaufzge mit nicht betretbaren Lastaufnahme

3、mitteln (enthlt nderungA1:2010)Englische bersetzung von DIN EN 12158-2:2011-04Monte-matriaux Partie 2: Monte-matriaux inclins dispositifs porte-charge non accessible(Amendement A1:2010 inclus)Traduction anglaise de DIN EN 12158-2:2011-04SupersedesDIN EN 12158-2:2001-01See start of applicationwww.beu

4、th.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.03.11 43DIN EN 12158-2:2011-04 A comma is used as the decimal marker. Start of application The start of application of this standard is 1 April 2011. National foreword This standard includes

5、 safety requirements. This standard has been prepared by Technical Committee CEN/TC 10 “Lifts, escalators and moving walks” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Maschinenbau (Mechanical Engineering Standards Committee), Working

6、 Committee NA 060-13-50 AA Bauaufzge of Section Bau- und Baustoffmaschinen. Representatives of manufacturers and users of builders hoists, and of the employers liability insurance associations contributed to this standard. This standard contains specifications meeting the essential requirements set

7、out in Annex I of the EU Machinery Directive 2006/42/EC, and which apply to machines that are either first placed on the market or commissioned within the EEA. This standard serves to facilitate proof of compliance with the essential requirements of that directive. Once this standard is cited in the

8、 Official Journal of the European Union, it is deemed a “harmonized” standard and thus, a manufacturer applying this standard may assume compliance with the requirements of the Machinery Directive (“presumption of conformity”). The European Standards referred to in Clause 2 and in the Bibliography o

9、f this standard have been published as the corresponding DIN EN or DIN EN ISO Standards with the same number. Where the International Standards referred to are not also DIN ISO Standards, there are no national standards available, except for the following: HD 22.1 S4 DIN VDE 0282-1 ISO 2408 DIN EN 1

10、2385-1 (similar) ISO 6336-1 DIN 3990-1 (not equivalent) ISO 6336-2 DIN 3990-2 (not equivalent) ISO 6336-3 DIN 3990-3 (not equivalent) Amendments This standard differs from DIN EN 12158-2:2001-01 as follows: a) the standard has been brought in line with the new “Machinery Directive”, Directive 2006/4

11、2/EC; b) Annex ZA (informative) “Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC” has been updated. Previous editions DIN EN 12158-2: 2001-01 2 DIN EN 12158-2:2011-04 National Annex NA (informative) Bibliography DIN 3990-1, Calculation of load ca

12、pacity of cylindrical gears Introduction and general influence factors DIN 3990-2, Calculation of load capacity cylindrical gears Calculation of pitting resistance DIN 3990-3, Calculation of load capacity of cylindrical gears Calculation of tooth strength DIN EN 12385-1, Steel wire ropes Safety Part

13、 1: General requirements DIN VDE 0282-1, Cables of rated voltages up to and including 450/750 V and having cross-linked insulation Part 1: General requirements 3 DIN EN 12158-2:2011-04 4 This page is intentionally blank EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12158-2:2000+A1 July 2010 I

14、CS 91.140.90 Supersedes EN 12158-2:2000English Version Builders hoists for goods - Part 2: Inclined hoists with non-accessible load carrying devices Monte-matriaux - Partie 2: Monte-matriaux inclins dispositifs porte-charge non accessible Bauaufzge fr den Materialtransport - Teil 2: Schrgaufzge mit

15、nicht betretbaren LastaufnahmemittelnThis European Standard was approved by CEN on 9 September 2000 and includes Amendment 1 approved by CEN on 12 June 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the

16、 status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, Germa

17、n). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus,

18、 Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT

19、 EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12158-2:2000+A1:2010: EEN 12158-2:2000+A1:2010 (E) 2 Contents Page F

20、oreword 3Introduction .41 Scope 42 Normative references 63 Terms and definitions .74 List of hazards 85 Safety requirements and/or measures . 106 Verification 257 User Information . 29Annex A (normative) European stormwind map . 36Annex B (informative) !Electric safety devices“ 37Annex ZA (informati

21、ve) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“ 38Bibliography . 39DIN EN 12158-2:2011-04 EN 12158-2:2000+A1:2010 (E) 3 Foreword This document (EN 12158-2:2000+A1:2010) has been prepared by Technical Committee CEN/TC 10 “Lifts, escalators a

22、nd moving walks“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2011, and conflicting national standards shall be withdrawn at the latest by Ja

23、nuary 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-06-12. This do

24、cument supersedes EN 12158-2:2000. The start and finish of text introduced or altered by amendment is indicated in the text by tags!“XThis document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements o

25、f EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, B

26、elgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DIN EN 121

27、58-2:2011-04 EN 12158-2:2000+A1:2010 (E) 4 Introduction This standard is one of a series of standards produced by CEN/TC 10/SC 1 as part of the CEN programme of work to produce machinery safety standards. The standard is a Type C standard relating to safety for builders hoists for goods. The extent

28、to which hazards are covered is indicated in the scope of this standard. In addition, machinery should comply as appropriate with !EN ISO 12100:2003“ for hazards which are not covered by this standard. !When provisions of this type C standard are different from those which are stated in type A or B

29、standards, the provisions of this type C standard take precedence over the provisions of the other standards, for machines that have been designed and built according to the provisions of this type C standard. The machinery concerned and the extent to which hazards, hazardous situations and events a

30、re covered are indicated in the scope of this European Standard.“ 1 Scope 1.1 This standard deals with power operated temporarily installed builders hoists intended for use by persons who are permitted to enter sites of engineering and construction, serving either one upper landing or a work area ex

31、tending to the end of the guides, (e.g. a roof) having a load carrying device (lcd): which is intended for the transportation of goods only; where it is forbidden for persons to step upon it at any time; which is guided; which is designed to travel at an angle of at least 30 degrees to the vertical

32、but may be used at any angle between the vertical and the maximum inclination as specified by the manufacturer; which is sustained by steel wire rope and a positive drive system; which is controlled by hold-to-run controls by the operator; which does not benefit from the use of any counterweight; wh

33、ich has a maximum rated load of 300 kg; which has a maximum speed of 1,00 m/s; and where the guides require support from separate structures. DIN EN 12158-2:2011-04 EN 12158-2:2000+A1:2010 (E) 5 1.2 The standard identifies hazards as listed in clause 4, which arise during the various phases in the l

34、ife of such equipment and describes methods for the elimination or reduction of these hazards when used as intended by the manufacturer. 1.3 This European standard does not specify the additional requirements for: operation in severe conditions (e.g. extreme climates, strong magnetic fields); lightn

35、ing protection; operation subject to special rules (e.g. potentially explosive atmospheres); electromagnetic compatibility (emission, immunity); handling of loads the nature of which could lead to dangerous situations (e.g. molten metal, acids/bases, radiating materials, fragile loads); the use of c

36、ombustion engines; the use of remote controls; hazards occurring during manufacture; hazards occurring as a result of mobility; hazards occurring as a result of being erected over a public road; earthquakes; noise. 1.4 This standard is not applicable to permanently installed lifts; builders hoists f

37、or persons and materials; builders hoists for the transport of goods with accessible platforms; builders hoists with an lcd driven by hydraulic jack (directly or indirectly); furniture hoists; conveyors; work cages suspended from lifting appliances; work platforms carried on the forks of fork trucks

38、; work platforms; funiculars; lifts specially designed for military purposes; mine lifts; DIN EN 12158-2:2011-04 EN 12158-2:2000+A1:2010 (E) 6 theatre elevators; special purpose hoists. 1.5 The safety requirements and/or measures of this standard deal with the design of the base frame, guide rails,

39、lcd, drive unit, electrical and/or hydraulic installation and the control of the hoist. Included is the design of any guide rail support but not the design of the supporting structure (e.g. building or scaffold) and any ties. Other aspects such as base enclosure, the design of any concrete, hard cor

40、e, timber or other foundation arrangement, hoistway protection and the upper landing are dealt with in the users manual section of this standard. 2 Normative references !The following referenced documents are indispensable for the application of this document. For dated references, only the edition

41、cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.“ !deleted text“ !EN 982:1996, Safety of machinery Safety requirements for fluid power systems and their components Hydraulics“ EN 1088:1995, Safety of machinery Interlocking devic

42、es associated with guards Principles for design and selection !EN 60204-32:2008, Safety of machinery Electrical equipment of machines Part 32: Requirements for hoisting machines (IEC 60204-32:2008)“ !EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989)“ !EN 60947-5-

43、1:2004, Low-voltage switchgear and controlgear Part 5-1: Control circuit devices and switching elements Electromechanical control circuit devices (IEC 60947-5-1:2003)“ !EN ISO 4871:1996, Acoustics Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)“ !EN I

44、SO 12100-1:2003, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology (ISO 12100-1:2003)“ !EN ISO 12100-2:2003, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003)“ !EN ISO 13850:2008, S

45、afety of machinery Emergency stop Principles for design (ISO 13850:2006)“ !EN ISO 13857:2008, Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)“ !HD 22.1 S4:2002, Cables of rated voltages up to and including 450/750 V and having cros

46、s-linked insulation Part 1: General requirements“ !ISO 2408:2004, Steel wire ropes for general purposes Minimum requirements“ !ISO 4302:1981, Cranes Wind load assessment“ !ISO 4309:2004, Cranes Wire ropes Care, maintenance, installation, examination and discard“ DIN EN 12158-2:2011-04 EN 12158-2:200

47、0+A1:2010 (E) 7 3 Terms and definitions !For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following apply.“ !3.1 working load/rated load“ maximum load which the hoist has been designed to carry in service. This load may depend on the configuration of

48、the hoist (i.e. inclination, length of guide rail, load carrying device) 3.2 rated speed speed of the lcd for which the equipment has been designed 3.3 positive drive drive using means other than friction 3.4 rope hoist hoist which uses rope as the load suspension system 3.5 wire rope termination ad

49、aption at the end of a wire rope permitting attachment 3.6 check valve valve, which allows flow of hydraulic fluid in the desired direction only if a predetermined pressure is maintained at the valve 3.7 base frame lowest framework of the hoist, upon which all other components are mounted 3.8 chassis chassis are base frames which enable road transport of the hoist 3.9 guide ra