1、October 2010 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC
2、S 23.060.30!$kSd“1724865www.din.deDDIN EN 12288Industrial valves Copper alloy gate valvesEnglish translation of DIN EN 12288:2010-10Industriearmaturen Schieber aus KupferlegierungenEnglische bersetzung von DIN EN 12288:2010-10Robinetterie industrielle Robinets-vannes en alliage de cuivreTraduction a
3、nglaise de DIN EN 12288:2010-10SupersedesDIN EN 12288:2003-11www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.2509.10 DIN EN 12288:2010-10 2 A comma is used as the decimal marker. National foreword This standard has been prepared by
4、 Technical Committee CEN/TC 69 “Industrial valves” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Armaturen (Valves Standards Committee), Working Committee NA 003-01-02 AA Schieber. Amendments This standard differs from DIN EN 12288:2003
5、-11 as follows: a) normative references in Clauses 2 and 3, Subclauses 4.1.1, 4.1.4, Table 5, Subclause 4.2.4.3, Tables A.1, A.2 and in Table B.1 have been updated; b) Table 5 and Table B.1 have been corrected; c) in Table ZA.1: Subclause 4.2 has been correlated to PED, Annex I, section 2.1; Subclau
6、se 4.2.3 has been correlated to PED, Annex I, section 2.2; the correlation of Subclause 4.2.3 to PED, Annex I, section 2.2.1 has been deleted; the correlation of Subclause 4.2.6 to PED, Annex I, section 2.5 has been deleted; the correlation of Annex A to PED, Annex I, section 4.2 has been deleted. P
7、revious editions DIN 3352-11: 1981-12 DIN 3352-12: 1981-12 DIN EN 12288: 2003-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12288 May 2010 ICS 23.060.30 Supersedes EN 12288:2003English Version Industrial valves - Copper alloy gate valves Robinetterie industrielle - Robinets-vannes en allia
8、ge de cuivre Industriearmaturen - Schieber aus Kupferlegierungen This European Standard was approved by CEN on 16 April 2010. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard w
9、ithout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other langu
10、age made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoni
11、a, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPI
12、SCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12288:2010: EEN 12288:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms an
13、d definitions .54 Requirements .64.1 Classification 64.1.1 Nominal sizes .64.1.2 Nominal size relationships .74.1.3 PN and Class designations .84.1.4 Valve series 94.2 Design .94.2.1 General 94.2.2 Materials .94.2.3 Pressure/temperature ratings .94.2.4 Dimensions .94.2.5 Operation . 114.2.6 Auxiliar
14、y connections 124.3 Functional characteristics . 124.3.1 Shell design strength . 124.3.2 Obturator design strength . 124.3.3 Shell tightness 124.3.4 Seat tightness . 124.3.5 Flow characteristics . 134.3.6 Sizing the operating element . 145 Test procedures 145.1 Production pressure testing 145.2 Appl
15、icability of gas tests . 155.3 Test durations . 156 Declaration of compliance . 157 Designation . 158 Marking and preparation for storage and transportation . 168.1 Required markings . 168.1.1 Mandatory markings . 168.1.2 Supplementary markings . 168.1.3 Other markings . 168.1.4 Omission of markings
16、 178.2 Preparation for storage and transportation . 178.2.1 Protection 178.2.2 Obturator position 178.2.3 Body ends 17Annex A (normative) Materials . 18Annex B (normative) Pressure/temperature ratings . 20B.1 Valves with metallic body seats and obturator seats . 20B.2 Valves with non-metallic obtura
17、tor seats and/or body seats . 21Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 22Bibliography . 23DIN EN 12288:2010-10 EN 12288:2010 (E) 3 Foreword This document (EN 12288:2010) has been prepared by Technical Committee CEN
18、/TC 69 “Industrial valves”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2010, and conflicting national standards shall be withdrawn at the l
19、atest by November 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12288:2003 This document has been
20、prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 97/23/EC. For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document. This document supersedes E
21、N 12288:2003 where the following modifications were made: a) the normative references were updated in Clauses 2 and 3, in 4.1.1, in 4.1.4, in Table 5, in 4.2.4.3, in Tables A.1 and A.2, in Table B.1; b) Table 5 and Table B.1 were corrected; c) in Table ZA.1: 1) sub-clause 4.2 was correlated to PED A
22、nnex I, section 2.1; 2) sub-clause 4.2.3 was correlated to PED Annex I, section 2.2; 3) correlation of sub-clause 4.2.3 to PED Annex I, section 2.2.1 was deleted; 4) correlation of sub-clause 4.2.6 to PED Annex I, section 2.5 was deleted; 5) correlation of Annex A to PED Annex I, section 4.2 was del
23、eted. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I
24、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 12288:2010-10 EN 12288:2010 (E) 4 1 Scope This European Standard applies to copper alloy gate valves for general use havi
25、ng flanged, threaded, capillary, compression or loose nut/union body ends. This European Standard specifies the design and performance requirements including materials, pressure/temperature ratings, dimensions, test procedures and marking. For some specific fields of application, for example, drinki
26、ng water or gas, valves to this European Standard can be used provided the requirements of the relevant performance standards are met. Approval by the relevant regulatory body may be required. The range of nominal sizes is DN 8 to DN 500 and of nominal diameters is 8 mm to 110 mm. The range of press
27、ure designations covered is PN 6; PN 10; PN 16; PN 20; PN 25; PN 32; PN 40; PN 63; Class 150 and Class 300. For the applicability of each nominal size/diameter and each pressure designation to the different types of valve end, see 4.1. 2 Normative references The following referenced documents are in
28、dispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 19:2002, Industrial valves Marking of metallic valves EN 558:2008, Industrial valves Fa
29、ce-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems PN and Class designated valves EN 736-1, Valves Terminology Part 1: Definition of types of valves EN 736-2, Valves Terminology Part 2: Definition of components of valves EN 736-3, Valves Terminology Part 3: Defi
30、nition of terms EN 1057, Copper and copper alloys Seamless round copper tubes for water and gas in sanitary and heating applications EN 1092-3:2003, Flanges and their joints Circular flanges for pipes, valves, fittings and accessories, PN designated Part 3: Copper alloy flanges EN 1759-3:2003, Flang
31、es and their joints Circular flanges for pipes, valves, fittings and accessories, Class designated Part 3: Copper alloy flanges EN 1982:2008, Copper and copper alloys Ingots and castings EN 12163:1998, Copper and copper alloys Rod for general purposes EN 12164:1998, Copper and copper alloys Rod for
32、free machining purposes EN 12167:1998, Copper and copper alloys Profiles and rectangular bar for general purposes EN 12168:1998, Copper and copper alloys Hollow rod for free machining purposes DIN EN 12288:2010-10 EN 12288:2010 (E) 5 EN 12266-1:2003, Industrial valves Testing of valves Part 1: Press
33、ure tests, test procedures and acceptance criteria Mandatory requirements EN 12266-2:2002, Industrial valves Testing of valves Part 2: Tests, test procedures and acceptance criteria Supplementary requirements EN 12420:1999, Copper and copper alloys Forgings“ EN 12449, Copper and copper alloys Seamle
34、ss, round tubes for general purposes EN 12516-3, Valves Shell design strength Part 3: Experimental method EN 12570, Industrial valves Method for sizing the operating element EN ISO 228-1:2003, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and des
35、ignation (ISO 228-1:2000) EN ISO 5210:1991, Industrial valves Multi-turn valve actuator attachments (ISO 5210:1991) ISO 7-1:1994, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation ASME B1.20.1:1983, Pipe threads, general purpose (inch) 3
36、Terms and definitions For the purposes of this document, the terms and definitions of types of valves and components and the terms and definitions given in EN 736-1, EN 736-2 and EN 736-3 apply, together with the following terms and definitions. NOTE The terms maximum allowable pressure, PS, and tes
37、t pressure, PT, defined in EU Directive 97/23/EC (PED) are equivalent to the terms allowable pressure, ps, and test pressure, pt, defined in EN 736-3:2008. 3.1 loose nut end body end provided with a tailpiece which retains a loose internally threaded nut or ring for connection to the mating componen
38、t 3.2 union end body end provided with an external thread to which is attached a threaded nut or ring, which retains a tailpiece for connection to the mating component 3.3 NPS alphanumeric designation of size for components of a pipework system, which is used for reference purposes and which compris
39、es, for the purpose of Class designated flanges according to this standard, the letters NPS followed by a dimensionless number which is indirectly related to the physical size of the bore or outside diameter of the end connections NOTE The number following the letters NPS does not represent a measur
40、able value and should not be used for calculation purposes except where specified in the relevant standard. See EN ISO 6708. Adapted from EN 1759-3:2003 DIN EN 12288:2010-10 EN 12288:2010 (E) 6 4 Requirements 4.1 Classification 4.1.1 Nominal sizes The nominal sizes applicable to each type of body en
41、d shall be as specified in Tables 1 and 2. NOTE 1 DN is applicable to flanged valves (PN designated) and loose nut/union end valves and NPS is applicable to flanged valves (Class designated). Threaded valves are normally identified by the thread size (NPS). Capillary and compression end valves are n
42、ormally identified by nominal diameter expressed as the nominal outside diameter of the connecting tube or pipe. The use of DN for valves with body ends other than flanged is permitted. NOTE 2 DN 8 is not listed in EN ISO 6708:1995 but is the commonly used equivalent nominal size for valves having s
43、ize threaded ends. NOTE 3 NPS and NPS are not listed in EN 1759-3:2003. Table 1 Nominal sizes for flanged, threaded and loose nut/union end valves Nominal size Valve body ends Nominal size Valve body ends Flanged Threaded Loose nut, union end Flanged Threaded PN Class PN Class DN 8 - - - DN 100 DN 1
44、00 4 4 DN 10 DN 10 - DN 10 DN 125 DN 125 5 - DN 15 DN 15 DN 15 DN 150 DN 150 6 - DN 20 DN 20 DN 20 DN 200 DN 200 8 - DN 25 DN 25 1 1 DN 25 DN 250 DN 250 10 - DN 32 DN 32 1 1 DN 32 DN 300 DN 300 12 - DN 40 DN 40 1 1 DN 40 DN 350 DN 350 14 - DN 50 DN 50 2 2 DN 50 DN 400 DN 400 16 - DN 65 DN 65 2 2 - D
45、N 450 DN 450 18 - DN 80 DN 80 3 3 - DN 500 DN 500 20 - DIN EN 12288:2010-10 EN 12288:2010 (E) 7 Table 2 Nominal diameters for capillary and compression end valves Nominal diameter mm Valve body ends Nominal diameter mm Valve body ends Capillary and compression ends for copper tubes Compression ends
46、for plastic pipe Capillary and compression ends for copper tubes Compression ends for plastic pipe 8 O - 40 X O 10 O O 40,5 X X12 O O 42 O - 14 X X 50 - O 14,7 X X 53,6 X X 15 O X 54 O - 16 X O 63 - O18 O X 64 O - 20 - O 66,7 O -21 X X 70 X - 22 O X 75 - O 25 X O 76,1 O -27,4 X X 80 X - 28 O X 88,9
47、O - 32 - O 90 - O34 X X 108 O - 35 O - 110 - ONOTE O = recommended European tube or pipe outside diameters. X = other European tube or pipe outside diameters. 4.1.2 Nominal size relationships The relationship between nominal size, DN, and body end types shall be as given in Table 3. DIN EN 12288:201
48、0-10 EN 12288:2010 (E) 8 Table 3 Relationship between nominal size, DN, and body end types Nominal size DN Body end types Flanged Threaded Loose nut, union end Capillary and compression ends for copper tubes Compression ends for plastic pipe PN Class Nominal size Nominal diameter DN NPS NPS DN DN 8
49、8 - - 8 ; 10 10 DN 10 10 - 10 12 ; 14 12 ; 14 DN 15 15 15 14,7 ; 15 ; 16 ; 18 14,7 ; 15 ;16 ;18 DN 20 20 20 21 ; 22 20 ; 21 ; 22 DN 25 25 1 1 25 25 ; 27,4 ; 28 25 ; 27,4 ; 28 DN 32 32 1 1 32 34 ; 35 32 ; 34 DN 40 40 1 1 40 40 ; 40,5 ; 42 40 ; 40,5 DN 50 50 2 2 50 53,6 ; 54 50 ; 53,6 DN 65 65 2 2 - 64 ; 66,7 ; 70 ; 76,1 63 ; 75 DN 80 80 3 3 - 80 ; 88,9 90 DN 100 10
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1