DIN EN 12317-2-2010 Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2 Plastic and rubber sheets for roof waterproofing German version EN 1231.pdf

1、December 2010 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 91.100.50!$lm“1735974www.din.deDDIN EN 12317-2Flexible sheets for waterproofing Determination of shear resistance of joints Part 2: Plastic and rubber sheets for roof waterproofingEnglish translation of DIN EN 12317-2:2010-12Abdichtungsbahnen Bestimmung des Scherwiderstandes der Fgenhte Teil 2: Ku

3、nststoff- und Elastomerbahnen fr DachabdichtungenEnglische bersetzung von DIN EN 12317-2:2010-12Feuilles souples dtanchit Dtermination de la rsistance au cisaillement des joints Partie 2: Feuilles dtanchit de toiture plastiques et lastomresTraduction anglaise de DIN EN 12317-2:2010-12SupersedesDIN E

4、N 12317-2:2001-01www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.1111.10 DIN EN 12317-2:2010-12 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 254 “Flexible sh

5、eets for waterproofing” (Secretariat: BSI, United Kingdom). The responsible German body involved in its preparation was the Normenausschuss Kunststoffe (Plastics Standards Committee), Working Committee NA 054-04-03 AA Baubahnen. Amendments This standard differs from DIN EN 12317-2:2001-01 as follows

6、: a) in Clause 10 “Test report”, new items “c) all details of how the weld was carried out” and “g) the shear resistance and the failure mode” have been added; b) in Clause 8 “Procedure”, it has been specified that the clear distance between the grips shall be between 3 and 4 times the width of the

7、joint with a minimum of 120 mm and a maximum of 200 mm; c) Annex A (informative) “Failure modes” has been added; d) Clause 2 “Normative references” has been updated; e) the standard has been editorially revised. Previous editions DIN 16726: 1986-12 DIN 16730: 1976-05 DIN 16731: 1976-05 DIN 16732-1:

8、1976-05 DIN 16732-2: 1976-05 DIN 16734: 1979-12 DIN 16935: 1971-05 DIN 16937: 1971-05 DIN 16938: 1971-05 DIN EN 12317-2: 2001-01 National Annex NA (informative) Bibliography DIN EN 13956, Flexible sheets for waterproofing Plastic and rubber sheets for roof waterproofing Definitions and characteristi

9、cs 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12317-2 July 2010 ICS 91.100.50 English Version Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing Feuilles souples dtanchit - Dtermination de la rsistanc

10、e au cisaillement des joints - Partie 2: Feuilles dtanchit de toiture plastiques et lastomres Abdichtungsbahnen - Bestimmung des Scherwiderstandes der Fgenhte - Teil 2: Kunststoff- und Elastomerbahnen fr Dachabdichtungen This European Standard was approved by CEN on 29 May 2010. CEN members are boun

11、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CE

12、N Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same stat

13、us as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal

14、, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means res

15、erved worldwide for CEN national Members. Ref. No. EN 12317-2:2010: EEN 12317-2:2010 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Principle 55 Apparatus .56 Sampling .67 Preparation of test pieces and test specimens 68 Procedure .79 Expres

16、sion of results 79.1 Jointing information 79.2 Evaluation .79.3 Precision of the test method 710 Test report 7Annex A (informative) Failure modes 9DIN EN 12317-2:2010-12 EN 12317-2:2010 (E) 3 Foreword This document (EN 12317-2:2010) has been prepared by Technical Committee CEN/TC 254 “Flexible sheet

17、s for waterproofing”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2011, and conflicting national standards shall be withdrawn at the latest by

18、January 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12317-2:2000. This European Standard “Flexib

19、le sheets for waterproofing - Determination of shear resistance of joints” consists of two parts: - Part 1: Bitumen sheets for roof waterproofing; - Part 2: Plastic and rubber sheets for waterproofing. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the fol

20、lowing countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slo

21、vakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DIN EN 12317-2:2010-12 EN 12317-2:2010 (E) 4 Introduction This European Standard is intended for characterisation of plastic and rubber sheets as manufactured or supplied before use. This test method relates to products or to their comp

22、onents where appropriate, and not to waterproofing membrane systems composed of such products and installed in the works. This test is intended to be used in conjunction with EN 13956, Flexible sheet for waterproofing Plastic and rubber sheets for roof waterproofing Definitions and characteristics.

23、DIN EN 12317-2:2010-12 EN 12317-2:2010 (E) 5 1 Scope This European Standard specifies a method for determining the resistance to shearing of joints between two adjacent sheets of the same plastic or rubber sheets for roof waterproofing. NOTE The shearing characteristics of a joint between two widths

24、 of plastic or rubber sheets vary considerably depending on the material, method of jointing, the size of the overlap and the workmanship. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited ap

25、plies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13416, Flexible sheets for waterproofing Bitumen, plastic and rubber sheets for roof waterproofing Rules for sampling EN ISO 7500-1, Metallic materials Verification of static uniaxial

26、testing machines Part 1: Tension/ compression testing machines Verification and calibration of the force-measuring system (ISO 7500-1:2004) 3 Terms and definitions For the purposes of this document, the following term and definition apply. 3.1 shear resistance maximum tensile force required to exten

27、d a prepared joint test specimen, in shear, until it breaks or separates 4 Principle The principle of the test is to pull a specimen of a joint in shear at a constant speed until it breaks or separates. The tensile force is continuously recorded throughout the test. 5 Apparatus Tensile testing machi

28、ne equipped with a continuous recording of force and corresponding extension and capable of maintaining a uniform speed of grip separation as specified below. The tensile testing machine shall have a sufficient loading capacity in excess of 2000 N and a grip separation speed of (100 10) mm/min. The

29、width of grips shall not be less than 50 mm. The tensile testing machine shall be equipped with grips of a type, which maintain or increase the clamping pressure as a function of the increase of the force applied to the test specimen. The test specimen shall be held so that it does not slip in the g

30、rips more than 2 mm. The method of gripping shall not induce premature rupture close to the grips. The force measuring system shall meet at least Class 2 of EN ISO 7500-1 (i.e. 2 %). DIN EN 12317-2:2010-12 EN 12317-2:2010 (E) 6 6 Sampling Samples shall be taken in accordance with EN 13416. 7 Prepara

31、tion of test pieces and test specimens Test pieces to be used for jointing should be previously conditioned for at least 20 h at (23 2) C and at a relative humidity between 30 % and 70 %. Test pieces of the sheet are joined by the method(s) to be used for installation, both for side lap and end lap

32、jointing, with an overlap that is specified for the product. After jointing, the test piece shall be conditioned for a minimum of 2 h at (23 2) C and at (50 5) % RH before testing unless the manufacturer recommends differently. From each of these joint test pieces five rectangular test specimens (50

33、 1) mm wide shall be taken perpendicular to the joint. They shall have such a length, so that the ends of the initial distance between the two grips is (200 5) mm with the joint in the middle (see Figure 1). Dimensions in millimetres 1w200 5Key 1 grip w width of joint Figure 1 Shear strength testing

34、 of joint DIN EN 12317-2:2010-12 EN 12317-2:2010 (E) 7 8 Procedure The test specimen shall be firmly held in the grips of the tensile testing machine, taking care that the longitudinal axis of the test specimen, the axis of the tensile testing machine and the grips are correctly aligned. Each test s

35、pecimen shall be marked at the grips in order to identify any slippage out of the grips. The clear distance between the grips shall be between 3 and 4 times the width of the joint with a minimum of 120 mm and a maximum of 200 mm. No preload shall be applied. The test is carried out on a test specime

36、n at a temperature of (23 2) C and at a constant separating speed for the grips of (100 10) mm/min. The applied tensile force shall be recorded continuously until the test specimen ruptures or shears. The mode of failure shall be recorded. 9 Expression of results 9.1 Jointing information State all r

37、elevant information on the formation and the conditioning of the joint. 9.2 Evaluation The mode of failure of each of the specimens shall be reported (see Annex A). The shear resistance of the specimen is the maximum force recorded during the test. List the individual values for each set of five spe

38、cimens in Newton. Calculate and state the shear resistance of the joint as the mean value to the nearest Newton. Calculate and state the standard deviation. Disregard any test result where the test specimen breaks less than 10 mm from the grips or slips by more than the permitted limit within the gr

39、ips of the tensile testing machine, and retest with a replacement specimen. 9.3 Precision of the test method No information is available at this time. 10 Test report The test report shall include at least the following information: a) reference to this document (EN 12317-2) and any deviation from it

40、; b) all details necessary to identify the product tested; c) all details of how the weld was carried out; d) information on sampling in accordance with Clause 6; e) details of preparation of the test specimen in accordance with Clause 7; DIN EN 12317-2:2010-12 EN 12317-2:2010 (E) 8 f) test results

41、in accordance with Clause 9; g) the shear resistance and the failure mode; h) any peculiarities in the method employed or encountered during the test; i) date of the test(s). DIN EN 12317-2:2010-12 EN 12317- 2: 2010 ( E ) 9 An n e x A (informa tiv e ) Fai l u r e modes Figur e A . 1 Fa ilur e mode s DI N EN 12317- 2 : 2010 - 1 2 9