1、March 2016 English price group 7No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 97.140!%Le=“2416626www.din.deDIN EN
2、 12520Furniture Strength, durability and safety Requirements for domestic seating;English version EN 12520:2015,English translation of DIN EN 12520:2016-03Mbel Festigkeit, Dauerhaltbarkeit und Sicherheit Anforderungen an Sitzmbel fr den Wohnbereich;Englische Fassung EN 12520:2015,Englische bersetzun
3、g von DIN EN 12520:2016-03Mobilier Rsistance, durabilit et scurit Exigences relatives aux siges usage domestique;Version anglaise EN 12520:2015,Traduction anglaise de DIN EN 12520:2016-03SupersedesDIN EN 12520:2010-07www.beuth.deDocument comprises 9 pagesDTranslation by DIN-Sprachendienst.In case of
4、 doubt, the German-language original shall be considered authoritative.02.16 DIN EN 12520:2016-03 2 A comma is used as the decimal marker. National foreword This document (EN 12520:2015) has been prepared by Technical Committee CEN/TC 207 “Furniture” (Secretariat: UNI, Italy). The responsible German
5、 body involved in its preparation was DIN-Normenausschuss Holzwirtschaft und Mbel (DIN Standards Committee Timber and Furniture), Working Committee NA 042-05-15 AA Sitzmbel, Polstermbel und Tische. Amendments This standard differs from DIN EN 12520:2010-07 as follows: a) references to EN 1728:2000 h
6、ave been replaced by references to EN 1728:2012; b) Annex A (normative) “Backward fall test” has been deleted; c) the standard has been editorially revised. Previous editions DIN 68878-1: 1981-09, 1987-01 DIN V ENV 12520: 2000-08 DIN EN 12520: 2010-07 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NOR
7、M EN 12520 December 2015 ICS 97.140 Supersedes EN 12520:2010English Version Furniture - Strength, durability and safety - Requirements for domestic seating Mobilier - Rsistance, durabilit et scurit - Exigences relatives aux siges usage domestique Mbel - Festigkeit, Dauerhaltbarkeit und Sicherheit -
8、Anforderungen an Sitzmbel fr den Wohnbereich This European Standard was approved by CEN on 8 November 2015. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterat
9、ion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made b
10、y translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
11、 Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDI
12、ZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12520:2015 EEN 12520:2015 (E) 2 Contents Pag
13、e European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions . 4 4 Test sequence . 4 5 Constructional requirements . 4 5.1 General requirements . 4 5.2 Shear and squeeze points . 5 5.2.1 Shear and squeeze points when setting up and folding 5 5.2.2 Shear and squeeze points under
14、 influence of powered mechanisms 5 5.2.3 Shear and squeeze points during use 5 5.3 Stability . 5 5.4 Strength and durability . 5 5.4.1 General 5 5.4.2 Strength and durability requirements 7 6 Information for use 7 7 Test report . 7 DIN EN 12520:2016-03 EN 12520:2015 (E) 3 European foreword This docu
15、ment (EN 12520:2015) has been prepared by Technical Committee CEN/TC 207 “Furniture”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2016 and conflic
16、ting national standards shall be withdrawn at the latest by June 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document s
17、upersedes EN 12520:2010. In comparison with EN 12520:2010, the following changes have been made: a) references to EN 1728:2000 were updated to EN 1728:2012; b) Annex A (normative) “Backward fall test” was deleted; c) the standard was editorially revised. According to the CEN-CENELEC Internal Regulat
18、ions, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Ital
19、y, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 12520:2016-03 EN 12520:2015 (E) 4 1 Scope This European Standard specifies the minimum requirements for the safety, strength
20、and durability of all types of domestic seating for adults. It does not apply to ranked seating, seating for non-domestic use, office work chairs, office visitors chairs, chairs for educational institutions, outdoor seating and to links for linked seating for which European Standards exist. It does
21、not include requirements for the durability of upholstery materials, castors, reclining and tilting mechanisms and seat height adjustment mechanisms. It does not include requirements for electrical safety. It does not include requirements for the resistance to ageing, degradation, flammability and e
22、rgonomics. The tests are based on use by persons weighing up to 110 kg. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated refere
23、nces, the latest edition of the referenced document (including any amendments) applies. EN 1022, Domestic furniture - Seating - Determination of stability EN 1728:2012 , Furniture - Seating - Test methods for the determination of strength and durability 3 Terms and definitions For the purposes of th
24、is document, the following terms and definitions apply. 3.1 accessible part part to which access can easily be gained by the user when the seating is in its intended configuration of use and for which the probability of unintentional user contact is high 3.2 part accessible during setting up and fol
25、ding part to which access can only be gained when setting up and folding the furniture 3.3 shear and squeeze point shear and squeeze point exists if the distance between two accessible parts moving relative to each other can be more than 7 mm or less than 18 mm in any position during movement 4 Test
26、 sequence The tests shall be carried out in the order in which they are listed in this document. 5 Constructional requirements 5.1 General requirements All parts of the seating with which the user comes into contact, during intended use, shall be designed to ensure that physical injury and damage ar
27、e avoided. N1)National footnote: Corresponds to DIN EN 1728:2014-02, Furniture Seating Test methods for the determination of strength and durability (EN 1728:2012 + AC:2013) N1)DIN EN 12520:2016-03 EN 12520:2015 (E) 5 These requirements are met when: a) edges of the seat, back rest and arm rests, wh
28、ich are in contact with the user when sitting are rounded or chamfered. All other edges accessible during use shall be free from burrs and/or sharp edges; b) ends of hollow components are closed or capped. Movable and adjustable parts shall be designed so that injuries and inadvertent operation are
29、avoided. It shall not be possible for any load bearing part of the seating to come loose unintentionally. All parts which are lubricated to assist sliding shall be designed to protect users from lubricant stains when in normal use. 5.2 Shear and squeeze points 5.2.1 Shear and squeeze points when set
30、ting up and folding Unless 5.2.2 or 5.2.3 are applicable, shear and squeeze points, as defined in 3.3, that are created only during setting up and folding, including tipping seat, are acceptable, because the user can be assumed to be in control of his/her movements and to be able to cease applying t
31、he force immediately upon experiencing pain. The edges of parts moving relative to each other and creating shear and squeeze points shall be as specified in 5.1. 5.2.2 Shear and squeeze points under influence of powered mechanisms With the exception of tipping seats there shall be no shear and squee
32、ze points created by parts of the seating under powered mechanisms, e.g. springs and gas lifts. NOTE Electrically operated seating is covered by EEC Directives for EMC, Machinery, Low Voltage or Medical Devices. 5.2.3 Shear and squeeze points during use There shall be no shear and squeeze points cre
33、ated by loads applied during normal use. The loads applied during normal use can be found in Table 1. Shear and squeeze points are not acceptable if a hazard is created by the weight of the user during normal movements and actions, e.g. attempting to move the seating by lifting the seat or by adjust
34、ing the backrest. NOTE This hazard is best prevented by the use of automatic locking mechanisms. 5.3 Stability The seating shall fulfil the relevant requirements of EN 1022. 5.4 Strength and durability 5.4.1 General Seating shall be tested for strength and durability according to and in the order gi
35、ven in Table 1 and in accordance with the test conditions contained in EN 1728:2012. DIN EN 12520:2016-03 EN 12520:2015 (E) 6 Table 1 Tests and test sequence Test Reference Test parameters 1. Seat static load and back static load test EN 1728:2012, 6.4 Seat force F1, N Back force F2, N Minimum back
36、force, N Load applied to seats not being tested, N Cycles 1 300 450 410 750 10 2. Seat front edge static load test EN 1728:2012, 6.5 Force, N Load applied to seats not being tested, N Cycles 1 300 750 10 3. Foot rest static load testaEN 1728:2012, 6.8 Force, N Minimum seat force, N Cycles 1 000 750
37、10 4. Arm rest sideways static load test EN 1728:2012, 6.10 Force, N Cycles 300 10 5. Arm rest downwards static load test EN 1728:2012, 6.11 Force, N Cycles 700 10 6. Combined seat and back durability testeEN 1728:2012, 6.17 Seat force F3, N, Back force F4, N Load applied to seats not being tested,
38、N Cycles 1 000 300 750 25 000 7. Seat front edge durability testdEN 1728:2012, 6.18 Force, N Cycles 800 20 000 8. Arm rest durability test EN 1728:2012, 6.20 Force, N Cycles 400 10 000 9. Leg forward static load test EN 1728:2012, 6.15 Force, N (max.) Seat load, N Cycles 400 1 000 10 10. Leg sideway
39、s static load test EN 1728:2012, 6.16 Force, N (max.) Seat load, N Cycles 300 1 000 10 11. Seat impact test EN 1728:2012, 6.24 Drop height, mm Cycles 180 10 12. Backward fall testbEN 1728:2012, 6.28 Number of impacts 5 13. Back impact testcEN 1728:2012, 6.25 Height of fall, mm or angle, Cycles 120 2
40、8 10 aThis test is only applicable to seating with a seat height greater than 600 mm. bThis test is only for single seating units where the back will be the first part of the structure to strike the floor and the force used to overturn the chair rearwards is less than 30 N. cThis test is for all sea
41、ting not tested in accordance with Test 12. dIn derogation of EN 1728:2012 the loading points shall be 80 mm from the relevant edges of the seat. eThe minimum back force is the force that just prevents rearward overturning. DIN EN 12520:2016-03 EN 12520:2015 (E) 7 5.4.2 Strength and durability requi
42、rements The strength and durability requirements are fulfilled when during and after testing in accordance with Table 1: a) there are no fractures of any member, joint or component; b) there are no loosening of joints intended to be rigid; c) seating fulfils its functions after removal of the test l
43、oads; d) seating fulfils the stability requirements. 6 Information for use Information for use shall be available in the language of the country in which it will be delivered to the end user. It shall contain at least the following details: a) assembly instructions, where applicable; b) instructions
44、 for the care and maintenance of the seating; c) if the seating is fitted with seat height adjustments with energy accumulators, an additional note is required pointing out that only trained personnel may replace or repair seat height adjustment components with energy accumulators. 7 Test report The
45、 test report shall include at least the following information: a) reference to this European Standard; b) piece of furniture tested, e.g. description of item, specification, drawings, photographs; c) details of defects observed before testing; d) any variation from the specified temperature range; e) test results; f) name and address of the test facility; g) date of test. DIN EN 12520:2016-03
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1