1、October 2011 Translation by DIN-Sprachendienst.English price group 9No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS
2、 45.060.20!$u“1822588www.din.deDDIN EN 12561-7Railway applications Tank wagons Part 7: Platforms and laddersEnglish translation of DIN EN 12561-7:2011-10Bahnanwendungen Kesselwagen Teil 7: Arbeitsbhnen und LeiternEnglische bersetzung von DIN EN 12561-7:2011-10Applications ferroviaires Wagons citerne
3、s Partie 7: Plate-formes et chellesTraduction anglaise de DIN EN 12561-7:2011-10SupersedesDIN EN 12561-7:2004-07www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.109.113DIN EN 12561-7:2011-10 A comma is used as the decimal marker. Na
4、tional foreword This standard has been prepared by Technical Committee CEN/TC 256 “Railway applications” (Secretariat: DIN, Germany), Working Committee WG 20 “Tank wagons” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Fahrweg und Schien
5、enfahrzeuge (Railway Standards Committee), Working Committee NA 087-00-10 AA Gterfahrzeuge. Amendments This standard differs from DIN EN 12561-7:2004-07 as follows: a) the requirements have been brought in line with the modified RIV; b) the standard has been editorially revised. Previous editions DI
6、N 26022: 1962-06, 1973-11, 1980-10, 1992-04 DIN EN 12561-7: 2004-07 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12561-7 June 2011 ICS 45.060.20 Supersedes EN 12561-7:2004English Version Railway applications - Tank wagons - Part 7: Platforms and ladders Applications ferrovaires - Wagons ci
7、ternes - Partie 7: Plate-formes et chelles Bahnanwendungen - Kesselwagen - Teil 7: Arbeitsbhnen und Leitern This European Standard was approved by CEN on 3 June 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Sta
8、ndard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (Engli
9、sh, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, B
10、ulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE
11、FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12561-7:2011: E2 Contents Page Foreword 31
12、Scope 42 Normative references 43 Terms and definitions .44 Ladders .44.1 General 44.2 Main dimensions 64.3 Design values .64.4 Marking .65 Platforms 95.1 General 95.2 Design values 6 Walkways . 6.1 General . 6.2 Main dimensions . 106.3 Design values 107 Characteristics of the grating 107.1 Resistanc
13、e to friction . 107.2 Grating structure. 1 8 Fixing . 1 Bibliography . 1 Figures Figure 1 Terms 5Figure 2 Examples of rung cross sections 5Figure 3 Main dimensions of end ladders .7Figure 4 Main dimensions of lateral ladders . Figure 5 Clearance above and behind rung 8Figure 6 Location of protective
14、 device EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 00178999.3 Foreword This document (EN 12561-7:2011) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either
15、by publication of an identical text or by endorsement, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/o
16、r CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12561-7:2004. This European Standard Railway applications Tank wagons consists of the following parts: Part 1: Identification plates for tank wagons for the carriage of dangerous goods;
17、 Part 2: Bottom emptying devices for liquid products including vapour return; Part 3: Bottom filling and emptying devices for gases liquefied under pressure; Part 4: Devices for top filling and emptying of liquid products; Part 5: Devices for vapour return while filling or emptying of liquid product
18、s; Part 6: Manholes; Part 7: Platforms and ladders; Part 8: Heating connections. The changes made during this revision are editorial because of the change of the title of part 1 and the necessary updates of references. According to the CEN/CENELEC Internal Regulations, the national standards organiz
19、ations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portu
20、gal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 4 1 Scope This European Standard applies to ladders, platforms and walkways on tank wagons fitted with top devices. It does not apply to crossing gangways nor to steps in s
21、o far as they are covered by UIC leaflets. This European Standard defines the important dimensions for manufacturers and operators of such tank wagons and takes into consideration the relevant and applicable construction and safety guidelines. This European Standard applies to new tank wagons built
22、after the 1st January 2010. In consideration of the smaller loading gauge within the UK, this European Standard does not apply to wagons operating exclusively therein. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referenc
23、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 795, Protection against falls from a height Anchor devices Requirements and testing EN 14564,Tanks for transport of dangerous goods Terminology EN ISO 6346
24、:1995, Freight containers Coding, identification and marking (ISO 6346:1995) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 14564 and the following apply. 3.1 platform level floor at the top of the tank for inspection, maintenance and operational pur
25、poses 3.2 walkway structure supporting grating to provide access between ladders and platforms 3.3 protective device device to deflect operating personnel from protruding parts of a moving tank wagon in accordance with UIC 535-2 4 Ladders 4.1 General Where tank wagons are fitted with ladders, they s
26、hall either be fitted with one fixed ladder located at the end or with a fixed ladder on each side of the tank wagon. NOTE 1 The end ladder is usually fitted at the crossing gangway. Ladders shall be fitted with 2 lateral handrails. EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 5 NOTE 2 For traffic of
27、continental tank wagons running in Great Britain, the kinematic gauge for Great Britain rules defined in the Technical Specification for Interoperability for freight wagons (TSI) also apply and to avoid conflict between these rules, local arrangement for handrail should be allowed to stay in the gau
28、ge. The pitch of the ladder as shown in Figure 1 shall be between 75 and 90. Where the pitch is less than 75 steps shall be used in place of rungs. The depth of the steps shall be at least 80 mm. Key 1 Pitch 2 Handrails 3 String 4 Rung Figure 1 Terms The rungs and the steps shall be welded to the st
29、rings and shall be slip-resistant. Rung slip resistance can, for example, be achieved by using square or flat bars with a cross section as shown in Figure 2. Figure 2 Examples of rung cross sections EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 6 If they are from square or rectangular section, they sha
30、ll not have sharp edges. Steps shall have a grating according to the requirements of Clause 7. 4.2 Main dimensions The main dimensions of ladders shall be as shown in Figure 3 and Figure 4. All the rungs shall be equally spaced. The sides of square steel rungs shall be between 20 mm to 30 mm. Differ
31、ent shaped rungs of equivalent strength are permitted provided they are slip resistant (e.g. rectangular steel rungs with a cross section of 40 mm 8 mm). The clearance above and behind each rung shall be as shown in Figure 5. The handrail shall be made from circular cross section tubes or bars of at
32、 least 20 mm outside diameter. The ladder handrail shall be connected to the toe plates of the walkways or platforms. The clearance around the handrail shall be at least 100 mm. Where lateral ladders protrude more than 250 mm from the chassis of the tank wagon, a protective device shall be fitted at
33、 a height of between 1 200 mm to 1 400 mm above the rail (see Figure 6). The lateral ladders shall not infringe the loading gauge. 4.3 Design values Ladders shall be designed to withstand a static load of 2,0 kN in the centre of any rung. The maximum allowable elastic deformation under this load sha
34、ll not exceed 1/200 of the width. 4.4 Marking A warning sign for overhead electrical danger shall be located near to each ladder in accordance with EN ISO 6346:1995, Annex C or Technical Specification for Interoperability for Freight Wagons. EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 7 Dimensions in
35、 millimetres Key 1 Top of crossing gangway Figure 3 Main dimensions of end ladders EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 Dimensions in millimetres Key 1 Top of rail Figure 4 Main dimensions of lateral ladders 8 Dimensions in millimetres Key 1 Tank Figure 5 Clearance above and behind rung EN 125
36、61-7:2011 (E) DIN EN 12561-7:2011-10 Key 1 Protective device Figure 6 Location of protective device 9 5 Platforms 5.1 General Platforms shall be built in accordance with the following requirements: to be at least around the manhole, protective covers and the area around the nozzles; to be flat and h
37、orizontal; to have a free width of at least 300 mm; to have sufficient clearance around manlid swing bolts to allow easy operation; to be surrounded by a toe plate of 20 mm minimum height, except where a ladder or a walkway is attached; to be fitted with a fixed point in accordance with EN 795 to wh
38、ich a safety line can be attached; to have a grating according to the requirements of Clause 7. The platform, including the toe plates shall not infringe the loading gauge. The width of the platform and the height of the toe plates may need to be reduced for domestic traffic in Great Britain (see Te
39、chnical Specification for Interoperability for Freight Wagons). EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 5.2 Design values The platform shall be designed to withstand a load of 3 kN uniformly distributed over an area of 600 mm 300 mm. The deflection under this load shall not exceed 10 mm or 1/200
40、of the span, whichever is the smaller. 6 Walkways 6.1 General Walkways shall be built in accordance with the following requirements: to be flat and may have a maximum longitudinal slope of 5; to be surrounded by a toe plate of minimum 20 mm height, except where a ladder or a platform is attached; to
41、 be fitted with a safety rail with a minimum clearance of 100 mm around it (see Figures 3 and 4); to have a grating according to the requirements of Clause 7. It is recommended to have walkways at the same level as the platform. 10 6.2 Main dimensions The width of the walkways shall not be less than
42、 500 mm and shall not infringe the loading gauge. The width of the walkways, the height of the toe plates and the clearance around the safety rail may need to be reduced for domestic traffic in Great Britain (see Technical Specification for Interoperability for Freight Wagons). 6.3 Design values The
43、 walkway shall be designed to withstand a load of 3 kN uniformly distributed over an area of 600 mm 300 mm. The deflection under this load shall not exceed 10 mm or 1/200 of the span, whichever is the smaller. 7 Characteristics of the grating 7.1 Resistance to friction The average value of the frict
44、ion coefficient measured in three directions (lengthwise, breadthwise and diagonally) shall reach the following minimum values: a) in dry condition 0,65; b) in wet condition (water) 0,65; c) in oiled condition 0,30. Friction coefficient values shall be ascertained by means of a 100 mm 100 mm movable
45、 plate, on which a rubber pad with 80 I.R.H.D. hardness shall be glued; this plate shall be loaded to 750 N. For the measurements carried out with water or oil, the grating shall be fully immersed. EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 7.2 Grating structure To ensure that the gratings are suffi
46、ciently well adapted to winter conditions, a ratio of at least 50 % of void area to total area shall be observed. Only apertures with a minimum area of 400 mm shall be taken into account to determine this ratio. The void area is the free space afforded, in the vertical direction, by the grating aper
47、tures. 8 Fixing Where ladders, platforms and walkways are fixed to the shell of the tank wagon, doubler plates shall be used. The fixings shall be properly secured to discourage theft and minimise the risk of working loose. The attachment of the ladder to the vehicle shall not introduce unacceptable
48、 stresses during all conditions of operation. 11 EN 12561-7:2011 (E) DIN EN 12561-7:2011-10 Bibliography 1 ISO 48, Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD) 2 ISO 1496-3, Series 1 freight containers Specification and testing Part 3: Tank co
49、ntainers for liquids, gases and pressurized dry bulk 3 RID, Regulations concerning the International Carriage of Dangerous Goods by Rail1)implementing Commission Directives 2003/28/EC and 2003/29/EC. 4 TSI Rolling Stock Freight Wagons 5 UIC 535-2, Standardisation and positioning on wagons of steps, end platforms, gangways, handrails, tow hooks, automatic coupler (AC), automatic draw-on coupling and brake valve
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1