1、October 2009DEUTSCHE NORM English price group 8No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 55.140!$Z=“1552688www.d
2、in.deDDIN EN 12714Plastics drums Removable head (open head) drums with a nominal capacity of 25 l to60 lEnglish version of DIN EN 12714:2009-10Kunststofffsser Deckelfsser mit einem Nennvolumen von 25 l bis 60 lEnglische Fassung DIN EN 12714:2009-10Together with DIN EN ISO20848-1:2008-09,supersedesDI
3、N EN 12714:2000-03www.beuth.deDocument comprises pages12DIN EN 12714:2009-10 National foreword This standard has been prepared by Technical Committee CEN/TC 261 “Packaging” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Verpackungswesen
4、(Packaging Standards Committee), Technical Committee NA 115-02-03 AA Spund- und Deckelbehltnisse. Amendments This standard differs from DIN EN 12714:2000-03 as follows: a) The specifications for drums with nominal capacities of 120 l, 150 l and 220 l have been deleted as these are now covered in DIN
5、 EN ISO 20848-1. b) The standard has been editorially revised. Previous editions DIN 6131-4: 1985-07, 1989-08 DIN EN 12714: 2000-03 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12714 July 2009 ICS 55.140 Supersedes EN 12714:2000 English Version Plastics drums Removable head (open head) dru
6、ms with a nominal capacity of 25 l to 60 l Fts en matire plastique Fts ouverture totale dune capacit nominale de 25 l 60 l Kunststofffsser Deckelfsser mit einem Nennvolumen von 25 l bis 60 l This European Standard was approved by CEN on 27 June 2009. CEN members are bound to comply with the CEN/CENE
7、LEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any
8、CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions. CEN
9、 members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Swede
10、n, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. R
11、ef. No. EN 12714:2009: EEN 12714:2009 (E) 2 Contents Page Foreword 31 Scope 42 Terms and definitions .43 Requirements .53.1 Dimensions .53.2 Drum mass .53.3 Material identification symbol 53.4 Closures 53.5 Materials .53.6 Handling 53.7 Stacking 53.8 Finish 64 Designation 6Annex A (normative) Capaci
12、ty measurement method for removable head (open head) plastics drums 8A.1 Principle 8A.2 Apparatus .8A.3 Procedure for determination of total capacity 8A.4 Procedure for determination of brimful capacity .9A.5 Expression of results 9Bibliography . 10DIN EN 12714:2009-10 EN 12714:2009 (E) 3 Foreword T
13、his document (EN 12714:2009) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 201
14、0, and conflicting national standards shall be withdrawn at the latest by January 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights
15、. This document supersedes EN 12714:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany,
16、Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. DIN EN 12714:2009-10 EN 12714:2009 (E) 4 1 Scope This European Standard specifies the characteristics
17、 and dimensions of removable head (open head) plastics drums with a nominal capacity of 25 l to 60 l. This standard is not applicable to injection moulded pails. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 removable head (open head) drum
18、(OH) flat-ended or convex-ended circular cross-section packaging, the top end of which can be removed as a lid and is closed by means of a closing ring or other device 2.2 nominal capacity (NC) capacity in litres which, by convention, is used to represent a class of drums of similar brimful capaciti
19、es 2.3 brimful capacity (BC) volume of water in litres held by the drum when filled through the filling orifice to the point of overflowing NOTE Annex A specifies the method for measuring brimful capacity. 2.4 total capacity (TC) volume of water in litres held by the drum, with its lid on, when fill
20、ed completely, i.e. following the removal of any air trapped in the drum NOTE Annex A specifies the method for measuring total capacity. 2.5 overall height (ho) height of the finished drum, including the lid, from the base to the highest point NOTE See Figure 1. 2.6 overall diameter (do) maximum dia
21、meter of the drum, where relevant NOTE See Figure 1. 2.7 minimum opening (dm) minimum drum body opening size NOTE See Figure 1. 2.8 drum mass mass of the empty drum including all closures DIN EN 12714:2009-10 EN 12714:2009 (E) 5 3 Requirements 3.1 Dimensions The dimensions and tolerances of the drum
22、 shall be as listed in Tables 1 and 2 and as shown in Figure 1. The measurements shall be conducted at ambient conditions but shall not be made within 48 h of manufacture. NOTE Apart from the dimensions specified, there are no restrictions on drum shape. 3.2 Drum mass For drums with the nominal capa
23、cities specified, the mass tolerances shall be as indicated in Table 1. Table 1 Drum mass tolerances Nominal capacity Mass tolerance l % 25 530 5 50 460 4NOTE The defined mass should be agreed between the purchaser and the supplier. 3.3 Material identification symbol All the plastics components, exc
24、luding gaskets, shall be permanently marked with the relevant material identification symbol, i.e. the symbol identifying the material from which the component is made. 3.4 Closures The closure system shall consist of a lid and a closing ring or other device. NOTE For the purpose of transport and st
25、orage, the filled drum should be closed to the manufacturers recommendations. The closure system shall incorporate a facility for providing evidence of tampering. 3.5 Materials The drum shall be manufactured from either high density polyethylene or other suitable plastics materials appropriate to th
26、e physical and chemical requirements of its intended use. 3.6 Handling Provision for manual handling shall be provided. Adaptations for mechanical handling may be added but, if so, their construction should be adequate for normal static and dynamic handling of filled drums. 3.7 Stacking The drum sha
27、ll be capable of being stacked with or without pallets, according to the manufacturers recommendations. DIN EN 12714:2009-10 EN 12714:2009 (E) 6 3.8 Finish The external surface finish shall be suitable for the attachment of labels. NOTE 1 The nature of the internal and external finish should be agre
28、ed between the purchaser and the supplier. NOTE 2 The preferred colour option for the drum body is blue. The use of any other colour should be agreed between the purchaser and the supplier. 4 Designation A removable head (open head) drum (OH) manufactured in accordance with this Standard shall be de
29、signated in the following manner: Plastics drum OH EN 12714 NC Nominal capacity EXAMPLE 1 A removable head (open head) drum (OH) manufactured in accordance with this Standard with a nominal capacity of 25 l to 60 l would be designated: Plastics drum OH EN 12714 NC - 25 l to 60 l. EXAMPLE 2 A removab
30、le head (open head) drum with a nominal capacity of 50 l would be designated: Plastics drum OH EN 12714 NC - 50 l. NOTE Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory requirements which govern the transport of those goods in the cou
31、ntries concerned. In Europe, depending upon the mode of transport, this means meeting the requirements of: European Agreement Concerning the International Carriage of Dangerous Goods by Road (ADR); Regulations concerning the International Carriage of Dangerous Goods by Rail (RID); Technical Instruct
32、ions for the Safe Transport of Dangerous Goods by Air, Document 9284-AN/905 published by the Council of the International Civil Aviation Organization (ICAO); The International Maritime Dangerous Goods Code (IMDG-CODE) published by the International Maritime Organization (IMO). Table 2 Dimensions of
33、removable (open head) drums with a nominal capacity of 25 l to 60 l Nominal capacity (NC) l Minimum total capacity (TC) l Overall diameter (do) mm Minimum opening (dm) mm Overall heighta(ho) mm 25 26,5 305 5 250 435 6 a30 31 316 5 250 515 6 a50 52 380 5 250 590 10 a60 62 397 5 310 625 10 aNOTE Dimen
34、sions do, dmand hoare applicable to empty drums. a It is intended that these tolerances will be reduced to 5 mm at the five year review period. DIN EN 12714:2009-10 EN 12714:2009 (E) 7 Key dmMinimum opening doOverall diameter hoOverall height 1 Closing ring Figure 1 Removable head (open head) drum w
35、ith a nominal capacity of 25 l to 60 l DIN EN 12714:2009-10 EN 12714:2009 (E) 8 Annex A (normative) Capacity measurement method for removable head (open head) plastics drums A.1 Principle The capacity is determined by a gravimetric method i.e. by the measurement of the mass of water in the filled dr
36、um and its conversion to a capacity. A correction factor (see 4.1.1 of EN ISO 90-2:1999) may be applied according to Table A.1, but only if the weighing scale used is of a higher precision than the correction. NOTE For plastics drums the water temperature should not exceed 18 C. Table A.1 Correction
37、 factors Water temperature C Correction factor (F) 12 1,000 5 14 1,000 8 16 1,001 18 1,001 4 A.2 Apparatus Weighing scale, with an accuracy of at least 0,1% of the weight being measured. A.3 Procedure for determination of total capacity A.3.1 For removable head (open head) drums, place the lid, fitt
38、ed with a closure for filling purposes, on the drum and close it using the recommended method. A.3.2 Drill a hole of diameter 5 mm to 10 mm for venting at the highest point of the closed drum. NOTE The position of the hole depends on the profile of the top. A.3.3 Weigh the empty drum and record its
39、mass, m1, in grams. A.3.4 Measure the temperature of the tap water to be used to fill the drum. A.3.5 Fill the drum 100 % with water through the filling closure and make sure that air is vented through the drilled hole. NOTE For certain drums, the drum needs to be inclined or tilted, so that the fil
40、ling hole is at the highest position. A.3.6 Fit and secure the drum closure and remove any surplus water from the outside. DIN EN 12714:2009-10 EN 12714:2009 (E) 9 A.3.7 Weigh the filled drum and record its mass, m2, in grams. A.4 Procedure for determination of brimful capacity Follow the same proce
41、dure as for the determination of total capacity (see A.3) with the exception that no hole is drilled to vent entrapped air. Fill the drum, with the drum in the normal position for filling, until water overflows at the closure. A.5 Expression of results The difference between the mass of the filled d
42、rum, m2, and the mass of the empty drum, m1, (m2 - m1), if necessary multiplied by the correction factor (F), represents the capacity of the drum as determined by the procedure used. DIN EN 12714:2009-10 EN 12714:2009 (E) 10 Bibliography 1 European Agreement Concerning the International Carriage of
43、Dangerous Goods by Road (ADR), United Nations Economic Commission for Europe (UNECE) 2 Regulations concerning the International Carriage of Dangerous Goods by Rail (RID), Intergovernmental Organization for International Carriage by Rail (OTIF) 3 Technical Instructions for the Safe Transport of Dange
44、rous Goods by Air, Document 9284-AN/905 published by the Council of the International Civil Aviation Organization (ICAO) 4 International Maritime Dangerous Goods Code (IMDG-CODE), International Maritime Organization (IMO) 5 EN ISO 90-2:1999, Light gauge metal containers Definitions and determination of dimensions and capacities Part 2: General use containers (ISO 90-2:1997) DIN EN 12714:2009-10
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1