DIN EN 12802-2011 Road marking materials - Laboratory methods for identification German version EN 12802 2011《路标材料 实验室鉴定法 德文版 EN 12802-2011》.pdf

1、December 2011 Translation by DIN-Sprachendienst.English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I

2、CS 93.080.20!$xk_“1857260www.din.deDDIN EN 12802Road marking materials Laboratory methods for identificationEnglish translation of DIN EN 12802:2011-12Straenmarkierungsmaterialien Laborverfahren fr die IdentifikationEnglische bersetzung von DIN EN 12802:2011-12Produits de marquage routier Mthodes de

3、 laboratoire pour identificationTraduction anglaise de DIN EN 12802:2011-12SupersedesDIN EN 12802:2000-03www.beuth.deDocument comprises 35 pagesIn case of doubt, the German-language original shall be considered authoritative.12.11 DIN EN 12802:2011-12 2 A comma is used as the decimal marker. Nationa

4、l foreword This standard has been prepared by Technical Committee CEN/TC 226 “Road equipment” (Secretariat: AFNOR, France), Working Group WG 2 “Horizontal road signs” (lead-management: AENOR, Spain). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building a

5、nd Civil Engineering Standards Committee), Working Committee NA 005-10-22 AA Straenmarkierungen. Amendments This standard differs from DIN EN 12802:2000-03 as follows: a) normative references have been updated; b) Clause 3 “Terms and definitions” has been extended; c) Clause 5 “Test methods” has bee

6、n extended to include Table 1 “Tolerances”; d) Annexes A to H have been revised; e) Annex J has been deleted. Previous editions DIN EN 12802: 2000-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12802 June 2011 ICS 93.080.20 Supersedes EN 12802:2000English Version Road marking materials - La

7、boratory methods for identification Produits de marquage routier - Mthodes de laboratoire pour identification Straenmarkierungsmaterialien - Laborverfahren fr die Identifikation This European Standard was approved by CEN on 22 April 2011. CEN members are bound to comply with the CEN/CENELEC Internal

8、 Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

9、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versio

10、ns. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slov

11、enia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN n

12、ational Members. Ref. No. EN 12802:2011: EEN 12802:2011 (E) 2 Contents Foreword . 31 Scope . 42 Normative references . 43 Terms and definitions 44 Sampling 55 Test methods . 56 Test Report 9Annex A (normative) Paint Test method for the determination of the solids content 10Annex B (normative) Paint,

13、 thermoplastics and cold plastics Test method for the determination and identification of organic constituents 12Annex C (normative) Paint, thermoplastic and cold plastic Test method for the determination and identification of inorganic constituents 16Annex D (normative) Paint, thermoplastics and co

14、ld plastics Test method for the determination of the titanium (IV) dioxide content in the inorganic compound 18Annex E (normative) Paint, thermoplastics and cold plastics Test method for the determination of the glass bead content . 21Annex F (normative) Paint and cold plastics Test method for the d

15、etermination and identification of solvents 23Annex G (normative) Paint Test method for the determination of viscosity (Krebs-Stormer method) 26Annex H (normative) Paint, thermoplastics and cold plastics Test method for the determination of the ash content . 31Bibliography . 33DIN EN 12802:2011-12 E

16、N 12802:2011 (E) 3 Foreword This document (EN 12802:2011) has been prepared by Technical Committee CEN/TC 226 “Road equipment”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorse

17、ment, at the latest by December 2011, and conflicting national standards shall be withdrawn at the latest by December 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for ident

18、ifying any or all such patent rights. This document supersedes EN 12802:2000. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,

19、 Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. The Annexes A to H of this European Standard are normati

20、ve. This European Standard is one of a package of inter-related European Standards with a common date of withdrawal (dow) fixed on December 2011 (including the request of an extension fo the co-existence period): EN 1790, Road marking materials Preformed road markings, EN 1824, Road marking material

21、s Road trials, EN 1871, Road marking materials Paint, thermoplastic and cold plastic materials Specifications, EN 12802, Road marking materials Laboratory methods for identification, EN 13197, Road marking materials Wear simulator Turntable, EN 13212, Road marking materials Requirements for factory

22、production control, EN 13459, Road marking materials Sampling and testing. DIN EN 12802:2011-12 EN 12802:2011 (E) 4 1 Scope This document specifies laboratory methods for the identification of road marking materials used in horizontal signalization. It is not necessary, unless required, to perform a

23、ll of the tests described. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

24、 EN 1423, Road marking materials Drop on materials Glass beads, antiskid aggregates and mixtures of the two EN 1424, Road marking materials Premix glass beads EN 1790, Road marking materials Preformed road markings EN 13459, Road marking materials Sampling and testing EN ISO 11890-2, Paints and varn

25、ishes Determination of volatile organic compound (VOC) content Part 2: Gas-chromatographic method (ISO 11890-2:2006) EN ISO 15528, Paints, varnishes and raw materials for paints and varnishes Sampling (ISO 15528:2000) ISO 5725-2, Accuracy (trueness and precision) of measurement methods and results P

26、art 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 paints liquid product containing binders, pigments, extenders, solvents and additi

27、ves NOTE It can be supplied in single or multi-component systems. When applied it produces a cohesive film by the process of solvent evaporation, or solvent evaporation and a chemical reaction. 3.2 cold plastics viscous products supplied in two or multi-component forms (at least one main component a

28、nd a hardener system) and free from solvents NOTE The cohesive film is formed after mixing of all components only by a chemical reaction. Following the reaction, the liquid becomes a solid. 3.3 thermoplastics solvent-free marking substance supplied in block, granular or powder forms NOTE It is heate

29、d to a molten state and then applied. It forms a cohesive film by cooling. DIN EN 12802:2011-12 EN 12802:2011 (E) 5 4 Sampling Samples representative of each component of the material shall be taken from storage, or prior to application, in accordance with EN 13459. Smaller representative samples, o

30、f sufficient quantity to carry out all the tests required, shall be taken from the larger samples. For paints and cold plastics approximately 1 l of the basic component shall be taken. In the case of thermoplastic in powder form, sufficient quantity shall be taken in accordance with EN 13459 so that

31、 it can be melted in a metal container and mixed to a homogeneous mass. After cooling and casting into solid sheets or blocks, representative samples of approximately 1 kg of homogeneous solid material shall be taken for testing. 5 Test methods 5.1 General The standard test methods are listed in 5.2

32、 to 5.4. Alternative quantitative analytical test methods may be used providing that: the resulting values are comparable to those obtained using the standard methods; and, the repeatability of the alternative methods, determined in accordance with ISO 5725-2, can be shown to be not less than that o

33、f the methods given in this standard. 5.2 Paint 5.2.1 Density The density of the paint shall be determined using, either the method laid down in EN ISO 2811-1, or an alternative method complying with 5.1. 5.2.2 Solids content The solids content of the paint, expressed as a percentage, shall be deter

34、mined using, either the method described in Annex A, or an alternative method complying with 5.1. 5.2.3 Organic content and identification The type of organic materials, and the content expressed as a percentage, of the paint shall be determined using, either the method described in Annex B, or an a

35、lternative method complying with 5.1. 5.2.4 Inorganic content and identification The type of inorganic materials, and the content expressed as a percentage, of the paint shall be determined using, either the method described in Annex C, or an alternative method complying with 5.1. 5.2.5 Titanium dio

36、xide content The titanium dioxide content of the inorganic compound of the paint, expressed as a percentage, shall be determined, either by the method described in Annex D, or an alternative method complying with 5.1. 5.2.6 Glass bead content The glass bead content of the paint, expressed as a perce

37、ntage, shall be determined, either as described in Annex E, or an alternative method complying with 5.1. DIN EN 12802:2011-12 EN 12802:2011 (E) 6 5.2.7 Solvent content and identification The type of solvent, and the content expressed as a percentage, of the paint shall be determined using, either th

38、e method described in Annex F, or an alternative method complying with 5.1. 5.2.8 Viscosity The viscosity of the paint shall be determined using, either the method described in Annex G, or an alternative method complying with 5.1. 5.2.9 Ash content The ash content of the paint shall be determined us

39、ing, either the method described in Annex H, or an alternative method complying with 5.1. 5.3 Thermoplastics 5.3.1 Density The density of the thermoplastics shall be determined using, either the method laid down in EN ISO 2811-2, or an alternative method complying with 5.1. 5.3.2 Organic content and

40、 identification The type of organic materials, and the content expressed as a percentage, of the thermoplastics shall be determined using, either the method described in Annex B, or an alternative method complying with 5.1. 5.3.3 Inorganic content and identification The type of inorganic materials,

41、and the content expressed as a percentage, of the thermoplastics shall be determined using, either the method described in Annex C, or an alternative method complying with 5.1. 5.3.4 Titanium dioxide content The titanium dioxide content of the inorganic compound of the thermoplastics, expressed as a

42、 percentage, shall be determined, either by the method described in Annex D, or an alternative method complying with 5.1. 5.3.5 Glass bead content The glass bead content of the thermoplastics, expressed as a percentage, shall be determined, either as described in Annex E, or an alternative method co

43、mplying with 5.1. 5.3.6 Ash content The ash content of the thermoplastics shall be determined using, either the method described in Annex H, or an alternative method complying with 5.1. 5.4 Cold plastics 5.4.1 Density The density of the cold plastics shall be determined using, either the method laid

44、 down in EN ISO 2811-2, or an alternative method complying with 5.1. DIN EN 12802:2011-12 EN 12802:2011 (E) 7 5.4.2 Organic content and identification The type of organic materials, and the content expressed as a percentage, of the cold plastics shall be determined using, either the method described

45、 in Annex B, or an alternative method complying with 5.1. 5.4.3 Inorganic content and identification The type of inorganic materials, and the content expressed as a percentage, of the cold plastics shall be determined using, either the method described in Annex C, or an alternative method complying

46、with 5.1. 5.4.4 Titanium dioxide content The titanium dioxide content of the inorganic compound of the cold plastics, expressed as a percentage, shall be determined, either by the method described in Annex D, or an alternative method complying with 5.1. 5.4.5 Glass bead content The glass bead conten

47、t of the cold plastics, expressed as a percentage, shall be determined, either as described in Annex E, or an alternative method complying with 5.1. 5.4.6 Solvent content and identification The type of solvent, and the content expressed as a percentage, of the cold plastics shall be determined using

48、, either the method described in Annex F, or an alternative method complying with 5.1. 5.4.7 Viscosity The viscosity of the cold plastics shall be determined using, either the method laid down in EN ISO 2555 with a Type A viscosimeter, or an alternative method complying with 5.1. 5.4.8 Ash content The ash content of the cold plastics shall be determined using, either the method described in Annex H, or an alternative method complying with