DIN EN 12859-2011 Gypsum blocks - Definitions requirements and test methods German version EN 12859 2011《石膏块 定义 要求和试验方法 德文版本EN 12859-2011》.pdf

1、May 2011 Translation by DIN-Sprachendienst.English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 91

2、.100.10!$pWD“1775233www.din.deDDIN EN 12859Gypsum blocks Definitions, requirements and test methodsEnglish translation of DIN EN 12859:2011-05Gips-Wandbauplatten Begriffe, Anforderungen und PrfverfahrenEnglische bersetzung von DIN EN 12859:2011-05Carreaux de pltre Dfinitions, spcifications et mthode

3、s dessaiTraduction anglaise de DIN EN 12859:2011-05SupersedesDIN EN 12859:2008-06www.beuth.deDocument comprises pagesIn case of doubt, the German-language original shall be considered authoritative.3704.11 DIN EN 12859:2011-05 A comma is used as the decimal marker. Start of application The start of

4、application of this standard is due to be 1 August 2011. It should be noted that, in Germany, CE conformity marking of construction products will be permitted once this standard has been listed in the Bundesanzeiger (German Federal Law Gazette) and from the date given therein. National foreword This

5、 standard has been prepared by Technical Committee CEN/TC 241 “Gypsum and gypsum based products” (Secretariat: AFNOR, France). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Working Committee NA 005-09-10

6、 AA Gips und Gipsprodukte. Amendments This standard differs from DIN EN 12859:2008-06 as follows: a) further breaking loads have been included (Tables 4a, 4b); b) Annex B “Surface hardness” has been added; c) some slight corrections have been made to the text. Previous editions DIN 18163: 1954x-06,

7、1966-05, 1978-06 DIN EN 12859: 2001-11, 2008-06 DIN EN 12859/A1: 2004-08 2 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12859 February 2011 ICS 91.100.10 Supersedes EN 12859:2008English Version Gypsum blocks Definitions, requirements and test methods Carreaux de pltre Dfinitions, spcificatio

8、ns et mthodes dessai Gips-Wandbauplatten Begriffe, Anforderungen und Prfverfahren This European Standard was approved by CEN on 2 January 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a n

9、ational standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A

10、version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cypru

11、s, Czech Republic, Denmark, Estonia,Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMI

12、T EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12859:2011: EEN 12859:2011 (E) 2 Contents Page Foreword 4Introducti

13、on .51 Scope 62 Normative references 63 Terms, definitions and symbols .73.1 Terms and definitions .73.2 Symbols 94 Requirements 104.1 Fire behaviour . 104.1.1 Reaction to fire 104.1.2 Fire resistance . 104.2 Direct airborne sound insulation 104.3 Thermal properties . 104.3.1 Thermal resistance . 10

14、4.3.2 Thermal conductivity 104.4 Types of gypsum blocks 114.4.1 General . 114.4.2 Visual identification of gypsum blocks by pigmentation . 114.5 Release of dangerous substances 124.6 Dimensions and tolerances . 124.6.1 Dimensions 124.6.2 Tolerances . 124.7 Flatness of gypsum blocks 134.8 Dry density

15、 and tolerance 134.8.1 Classes of density 134.8.2 Tolerance . 134.9 Surface mass of gypsum blocks and tolerance 134.10 Bending strength 134.11 Moisture content . 144.12 pH . 154.13 Water absorption capacity . 154.13.1 Classification . 154.13.2 Requirement 154.14 Surface hardness 155 Test methods . 1

16、55.1 Sampling 155.2 Preparation of test pieces 155.3 Measurement of dimensions . 165.3.1 Thickness 165.3.2 Length 165.3.3 Height . 185.3.4 Cavity gypsum blocks 185.4 Flatness of gypsum blocks 195.4.1 Principle . 195.4.2 Apparatus 195.4.3 Procedure 195.4.4 Expression of results . 195.5 Mass of gypsum

17、 blocks . 195.5.1 Principle . 195.5.2 Apparatus 195.5.3 Procedure 19DIN EN 12859:2011-05 EN 12859:2011 (E) 3 5.5.4 Expression of results 195.6 Density of gypsum blocks 195.6.1 Principle 195.6.2 Apparatus . 195.6.3 Procedure . 205.6.4 Expression of results 205.7 Bending strength . 205.7.1 Principle 2

18、05.7.2 Apparatus . 205.7.3 Procedure . 215.7.4 Expression of results 215.8 Moisture content 215.8.1 Principle 215.8.2 Expression of results 215.9 Water absorption capacity (hydrophobic gypsum blocks only) 225.9.1 Principle 225.9.2 Apparatus . 225.9.3 Preparation of the test pieces 225.9.4 Procedure

19、. 225.9.5 Expression of results 225.10 pH measurement . 225.10.1 Principle 225.10.2 Apparatus . 225.10.3 Sampling. 235.10.4 Procedure . 235.10.5 Expression of results 235.11 Test reports 236 Evaluation of conformity 236.1 General . 236.2 Initial type testing 236.3 Factory production control. 247 Des

20、ignation of gypsum blocks 248 Marking, labelling and packaging 25Annex A (normative) Sampling for independent acceptance testing carried out by a third party . 26A.1 General . 26A.2 Sampling procedure 26Annex B (informative) Surface hardness 28B.1 General . 28B.2 Requirements . 28B.3 Test method . 2

21、8Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive . 30ZA.1 Scope and relevant characteristics . 30ZA.2 Procedure for attestation of conformity of gypsum blocks 31ZA.3 CE Marking and labelling 32Bibliography 35DIN EN 12859:20

22、11-05 EN 12859:2011 (E) 4 Foreword This document (EN 12859:2011) has been prepared by Technical Committee CEN/TC 241 “Gypsum and gypsum based products”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an ide

23、ntical text or by endorsement, at the latest by August 2011, and conflicting national standards shall be withdrawn at the latest by August 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held

24、responsible for identifying any or all such patent rights. This document supersedes EN 12859:2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship

25、 with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This European Standard includes: A normative annex concerning sampling for independent test; An informative annex recommending requirements and test method for measuring surface hardness. According to the CE

26、N/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Li

27、thuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. DIN EN 12859:2011-05 EN 12859:2011 (E) 5 Introduction Diagram 1 shows the relationship between this standard and the package of standards prepared to support

28、 the family of gypsum products. Figure 1 Family of gypsum binders and gypsum products DIN EN 12859:2011-05 EN 12859:2011 (E) 6 1 Scope This European Standard specifies the characteristics and performance of gypsum blocks with smooth faces for which the main intended uses are construction of non-load

29、 bearing partitions or independent wall linings and the fire protection of columns, lift shafts, shafts for services, etc. Gypsum blocks are not used to build ceilings. It covers the following performance characteristics related to the essential requirements: reaction to fire; resistance to fire; di

30、rect airborne sound insulation; release of dangerous substances; to be measured according to the corresponding European test methods, as well as: thermal resistance to be calculated from the thermal conductivity values given in 4.3.2. It describes the reference tests for technical specifications. Th

31、is European Standard covers also additional technical characteristics that are of importance for the use and acceptance of the product by the construction industry: convenience classes for density; convenience classes for pH. It provides for the evaluation of conformity of the product to this Europe

32、an Standard. This European Standard does not cover gypsum blocks of thickness less than 50 mm or gypsum storey height units. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For und

33、ated references, the latest edition of the referenced document (including any amendments) applies. EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using data from reaction to fire tests EN 13501-2, Fire classification of construction products and

34、 building elements Part 2: Classification using data from fire resistance tests, excluding ventilation services EN ISO 717-1, Acoustics Rating of sound insulation in buildings and of building elements Part 1: Airborne sound insulation (ISO 717-1:1996)1)1) This reference is impacted by the stand-alon

35、e amendment EN ISO 717-1:1996/A1:2006. DIN EN 12859:2011-05 EN 12859:2011 (E) 7 EN ISO 6946:2007, Building components and building elements Thermal resistance and thermal transmittance Calculation method (ISO 6946:2007) EN ISO 10140-3, Acoustics Laboratory measurement of sound insulation of building

36、 elements Part 3: Measurement of impact sound insulation (ISO 10140-3:2010) EN ISO 10456:2007, Building materials and products Hygrothermal properties Tabulated design values and procedures for determining declared and design thermal values (ISO 10456:2007) 3 Terms, definitions and symbols 3.1 Terms

37、 and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 gypsum block factory-made building element that is produced from calcium sulphate and water, that may incorporate fibres, fillers, aggregates and other additives as far as they are not classified as

38、dangerous substances in accordance with European regulations, and that may be coloured by pigmentation in accordance with the provisions of this standard NOTE The gypsum block is a rectangular parallelepiped with tongues and grooves on at least two of their opposite edges. 3.1.2 solid gypsum block g

39、ypsum block manufactured without cavities 3.1.3 cavity gypsum block gypsum block which incorporates preformed cavities 3.1.4 preformed cavity formed cavity parallel to the faces which may or may not pass completely through the block and which may run parallel with the height or the length NOTE See e

40、xample on Figure 2. 3.1.5 face plain and smooth surface intended to provide the finish of a partition NOTE See Figure 2. 3.1.6 edge extreme side of the gypsum block having tongues and grooves NOTE See Figure 2. 3.1.7 thickness distance between the two faces of a gypsum block NOTE See Figure 2. DIN E

41、N 12859:2011-05 EN 12859:2011 (E) 8 3.1.8 length greatest distance between two edges of a gypsum block NOTE See Figure 2. 3.1.9 height smaller distance between two edges of a gypsum block NOTE See Figure 2. DIN EN 12859:2011-05 EN 12859:2011 (E) 9 Key 1 Preformed cavities 2 Face 3 Thickness 4 Height

42、 5 Length Figure 2 Gypsum block 3.2 Symbols For the purposes of this document, the following symbols apply: gross dry density, in kilograms per cubic metre (kg/m3) thermal conductivity, in Watts per metre per Kelvin (W/mK) DIN EN 12859:2011-05 EN 12859:2011 (E) 10 23-50thermal conductivity of the ha

43、rdened plaster when in equilibrium at 23 C and 50 % relative humidity, in Watts per metre per Kelvin (W/mK) M mass of the gypsum block in kilograms (kg) R2F reaction to fire FR fire resistance R direct airborne sound insulation 4 Requirements 4.1 Fire behaviour 4.1.1 Reaction to fire Gypsum blocks a

44、re classified in Euroclass A.1 (no contribution to fire) without testing when they contain less than 1 % by weight or volume (whichever is the more onerous) of organic material. Gypsum blocks with 1 % or more, by weight or volume of organic material, shall be tested and classified in accordance with

45、 EN 13501-1. 4.1.2 Fire resistance Resistance to fire is a property of an assembled system and not of the product itself. When relevant, the fire resistance of a system including gypsum blocks assembled with adhesive for gypsum blocks shall be determined and classified in accordance with EN 13501-2.

46、 4.2 Direct airborne sound insulation Direct airborne sound insulation is a property of an assembled system and not of the product itself. When relevant, the direct airborne sound insulation of a system including gypsum blocks assembled with adhesive for gypsum blocks shall be determined in accordan

47、ce with EN ISO 10140-3 and EN ISO 717-1. 4.3 Thermal properties 4.3.1 Thermal resistance When the intended use of gypsum blocks is to contribute to thermal resistance in building construction works, the thermal resistance is calculated using the formula given in EN ISO 6946:2007. The values of thermal conductivity necessary for this calculation are given in 4.3.2 and thickness values to be used shall be measured accordi