1、December 2014 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).I
2、CS 77.150.30!%Zw“2275584www.din.deDDIN EN 13599Copper and copper alloys Copper plate, sheet and strip for electrical purposes;English version EN 13599:2014,English translation of DIN EN 13599:2014-12Kupfer und Kupferlegierungen Platten, Bleche und Bnder aus Kupfer fr die Anwendung in der Elektrotech
3、nik;Englische Fassung EN 13599:2014,Englische bersetzung von DIN EN 13599:2014-12Cuivre et alliages de cuivre Plaques, tles et bandes en cuivre pour usages lectriques;Version anglaise EN 13599:2014,Traduction anglaise de DIN EN 13599:2014-12SupersedesDIN EN 13599:2014-03www.beuth.deIn case of doubt,
4、 the German-language original shall be considered authoritative.Document comprises 23 pages 11.14 DIN EN 13599:2014-12 2 A comma is used as the decimal marker. National foreword This document (EN 13599:2014) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys” (Secretariat:
5、 DIN, Germany). The responsible German body involved in its preparation was the DIN-Normenausschuss Nichteisenmetalle (DIN Standards Committee Nonferrous Metals), Working Committee NA 066-02-02 AA Walzerzeugnisse. The corrections made to DIN EN 13599:2014-03 are only relevant for the German version.
6、 Amendments This standard differs from DIN EN 13599:2002-07 as follows: a) Table 1, column “Cu-FRHC”, “Other elements” has been modified and a new footnote “d” has been added; b) normative references have been updated. Compared with DIN EN 13599:2014-03, the following corrections have been made to t
7、he German version only and therefore do not affect the English text: a) page 17, Table 5, right-most column “ber 700” and “bis 1 250”, line 3 for thicknesses “ber 0,1 bis 1,0” and line 4 for thicknesses “ber 1,0 bis 2,0”: the upper tolerance has been changed in each case from “+0,2” to “+ 2,0” (the
8、lower tolerance “0” has remained the same). Previous editions DIN 1751: 1925-07, 1933-12, 1963-10, 1973-06 DIN 1752: 1925-07, 1933-12 DIN 1791: 1933-12, 1963-10, 1973-06 DIN 1792: 1933-12 DIN VDE 500 = DIN 40500: 1934x-04 DIN 40500-1: 1959-06, 1962-10, 1970-09, 1980-04 DIN 46415: 1958-10 DIN EN 1359
9、9: 2002-07, 2014-03 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13599 January 2014 ICS 77.150.30 Supersedes EN 13599:2002English Version Copper and copper alloys - Copper plate, sheet and strip for electrical purposes Cuivre et alliages de cuivre - Plaques, tles et bandes en cuivre pour usa
10、ges lectriques Kupfer und Kupferlegierungen - Platten, Bleche und Bnder aus Kupfer fr die Anwendung in der Elektrotechnik This European Standard was approved by CEN on 3 November 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving
11、 this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three offici
12、al versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of A
13、ustria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sw
14、eden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for
15、CEN national Members. Ref. No. EN 13599:2014 EEN 13599:2014 (E) 2 Contents PageForeword 3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Designations 5 4.1 Material .5 4.2 Material condition 5 4.3 Product .5 5 Ordering information .6 6 Requirements .8 6.1 Composition .8 6.2 Mechanic
16、al properties .8 6.3 Bending characteristics 8 6.4 Electrical properties 8 6.5 Freedom from hydrogen embrittlement 8 6.6 Dimensions and tolerances 9 6.7 Edgewise curvature c 9 6.8 Surface condition.9 7 Sampling .9 7.1 General 9 7.2 Analysis 9 7.3 Mechanical and electrical tests . 10 8 Test methods .
17、 10 8.1 Analysis . 10 8.2 Tensile test 10 8.3 Hardness test 10 8.4 Bend test 10 8.5 Electrical resistivity test . 11 8.6 Hydrogen embrittlement test . 11 8.7 Retests . 12 8.8 Rounding of results 12 9 Declaration of conformity and inspection documentation . 12 9.1 Declaration of conformity 12 9.2 Ins
18、pection documentation . 12 10 Marking, packaging, labelling 12 Annex A (informative) Characteristics of coppers for electrical purposes 19 A.1 General grouping of copper types 19 A.2 General characteristics 19 A.3 Particular characteristics . 19 Bibliography . 21 DINEN 13599:2014-12EN 13599:2014 (E)
19、 3 Foreword This document (EN 13599:2014) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
20、 the latest by July 2014, and conflicting national standards shall be withdrawn at the latest by July 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or al
21、l such patent rights. This document supersedes EN 13599:2002. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 2 “Rolled flat products” to revise the following standard: EN 13599:2002, Copper and copper alloys Copper plate, sheet and strip for electrical purposes
22、The products specified in this European Standard are those which are especially suitable for electrical purposes, i.e. with specified electrical properties. Copper plate, sheet and strip for general purposes are specified in EN 1652. This is one of a series of European Standards for copper products
23、for electrical purposes. Other copper products are specified as follows: EN 13600, Copper and copper alloys Seamless copper tubes for electrical purposes EN 13601, Copper and copper alloys Copper rod, bar and wire for general electrical purposes EN 13602, Copper and copper alloys Drawn, round copper
24、 wire for the manufacture of electrical conductors EN 13604, Copper and copper alloys Products of high conductivity copper for electronic tubes, semiconductor devices and vacuum applications EN 13605, Copper and copper alloys Copper profiles and profiled wire for electrical purposes In comparison wi
25、th EN 13599:2002, the following significant changes were made: a) Table 2, Cu-FRHC, other elements content has been modified and a new footnote “d” has been added; b) the normative references have been updated. According to the CEN-CENELEC Internal Regulations, the national standards organizations o
26、f the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Net
27、herlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13599:2014-12 EN 13599:2014 (E) 4 1 Scope This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dime
28、nsions and form for copper plate, sheet and strip for electrical purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250 mm. The sampling procedures and the methods of test for verification of conformity to the requirements of this European St
29、andard are also specified. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do
30、cument (including any amendments) applies. EN 1655, Copper and copper alloys - Declarations of conformity EN 1976, Copper and copper alloys - Cast unwrought copper products EN 10204, Metallic products - Types of inspection documents EN ISO 2626, Copper - Hydrogen embrittlement test (ISO 2626) EN ISO
31、 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1) EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1) EN ISO 7438, Metallic materials - Bend test (ISO 7438) ISO 1811-2, Copper and copper alloys Selection a
32、nd preparation of samples for chemical analysis Part 2: Sampling of wrought products and castings 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 plate flat rolled product of rectangular cross-section with uniform thickness greater than 10 mm
33、 3.2 sheet flat rolled product of rectangular cross-section with uniform thickness from 0,2 mm up to and including 10 mm, supplied in straight lengths, usually with sheared or sawn edges Note 1 to entry: The thickness does not exceed one tenth of the width. 3.3 strip flat rolled product of rectangul
34、ar cross-section with uniform thickness from 0,05 mm up to and including 5,0 mm manufactured in coil and supplied in as sheared coils, traverse wound coils or cut to length, usually with slit edges Note 1 to entry: The thickness does not exceed one tenth of the width. DINEN 13599:2014-12EN 13599:201
35、4 (E) 5 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or by number (see Table 1). 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the
36、 same as those in other standards using the designation system in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412. 4.2 Material condition For the purposes of this standard,
37、the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: M Material condition for the product as manufactured without specified mechanical properties; H Material condition designated by the minimum value of hardness requirement for the p
38、roduct with mandatory hardness requirements; R Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elongation requirements. NOTE Some R. material conditions in this European Standard apply to products which also have
39、mandatory 0,2 % proof strength requirements. Exact conversion between material conditions designated H. and R. is not possible. Material condition is designated by only one of the above designations. 4.3 Product The product designation provides a standardised pattern of designation from which a rapi
40、d and unequivocal description of a product can be conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standar
41、d. The product designation for products to this European Standard shall consist of: denomination (Plate, Sheet or Strip); number of this European Standard (EN 13599); material designation, either symbol or number (see Table 1); material condition designation (see Table 2); DINEN 13599:2014-12EN 1359
42、9:2014 (E) 6 nominal dimensions; plate: thickness width length either “as manufactured” (ML) or “fixed” (FL) length; sheet: thickness width length either “as manufactured” (ML) or “fixed” (FL) length (see Example 1); strip (as sheared coils or as transverse wound coils on spools): thickness width (s
43、ee Example 2); strip (cut to length): thickness width length either “as manufactured” (ML) or “fixed” (FL) length. The derivation of a product designation is shown in Example 1. EXAMPLE 1 Sheet for electrical purposes conforming to this European Standard, in material designated either Cu-ETP or CW00
44、4A, in material condition H040, nominal thickness 6,0 mm, nominal width 600 mm, as manufactured length 2 000 mm, will be designated as follows: Sheet EN 13599 Cu-ETP H040 6,0 600 2 000ML or Sheet EN 13599 CW004A H040 6,0 600 2 000ML Denomination Number of this European Standard Material designation
45、Material condition designation Nominal dimension in millimetres EXAMPLE 2 Strip for electrical purposes conforming to this European Standard, in material designated either CuAg0,10 or CW013A, in material condition R290, nominal thickness 2,0 mm, nominal width 1 000 mm, will be designated as follows:
46、 Strip EN 13599 CuAg0,10 R290 2,0 1 000 or Strip EN 13599 CW013A R290 2,0 1 000 5 Ordering information In order to facilitate the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information:
47、a) quantity of product required: 1) plate: number of pieces or mass; 2) sheet: number of pieces or mass; 3) strip (as sheared coils or as transverse wound coils on spools): mass; 4) strip (cut to length): mass or number of pieces; DINEN 13599:2014-12EN 13599:2014 (E) 7 b) denomination (Plate, Sheet
48、or Strip); c) number of this European Standard (EN 13599); d) material designation (see 4.1 and Table 1); e) material condition designation (see 4.2 and Table 2); f) nominal dimensions: 1) plate, sheet, strip (cut to length): thickness for thicknesses from 0,05 mm up to and including 3,2 mm and with widths from 10 mm up to and including 200 mm, thickness tolerance either “normal” (N) or “special” (S) width length (either “as manufactured” or “fixed”
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1