1、September 2013 Translation by DIN-Sprachendienst.English price group 12No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).
2、ICS 77.150.30!%)English version EN 13602:2013,English translation of DIN EN 13602:2013-09Kupfer und Kupferlegierungen Gezogener Runddraht aus Kupfer zur Herstellung elektrischer Leiter;Englische Fassung EN 13602:2013,Englische bersetzung von DIN EN 13602:2013-09Cuivre et alliages de cuivre Fils rond
3、s en cuivre tirs pour la fabrication des conducteurs lectriques;Version anglaise EN 13602:2013,Traduction anglaise de DIN EN 13602:2013-09SupersedesDIN EN 13602:2002-07www.beuth.deDocument comprises 24 pagesIn case of doubt, the German-language original shall be considered authoritative.08.13DIN EN
4、13602:2013-09 2 A comma is used as the decimal marker. National foreword This document (EN 13602:2013) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Nichteise
5、nmetalle (Nonferrous Metals Standards Committee), Working Committee NA 066-02-04 AA Strangpress- und Zieherzeugnisse. The DIN Standard corresponding to the International Standard referred to in this document is as follows: IEC 60468 DIN IEC 60468 Amendments This standard differs from DIN EN 13602:20
6、02-07 as follows: a) terms and definitions have been updated; b) normative references have been updated; c) the standard has been editorially revised. Previous editions DIN VDE 500 = DIN 40500: 1934x-04 DIN 40500-4: 1962-10, 1973-09 DIN 40500-5: 1978-03, 1983-06 DIN EN 13602: 2002-07 Nationaler Anha
7、ng NA (informativ) Literaturhinweise DIN IEC 60468, Method of measurement of resistivity of metallic materials EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13602 June 2013 ICS 77.150.30 Supersedes EN 13602:2002English Version Copper and copper alloys - Drawn, round copper wire for the manufa
8、cture of electrical conductors Cuivre et alliages de cuivre - Fils ronds en cuivre tirs pour la fabrication des conducteurs lectriques Kupfer und Kupferlegierungen - Gezogener Runddraht aus Kupfer zur Herstellung elektrischer Leiter This European Standard was approved by CEN on 25 April 2013. CEN me
9、mbers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applica
10、tion to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manag
11、ement Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia
12、, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000
13、Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13602:2013: EEN 13602:2013 (E) 2 Contents Page Foreword . 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 6 4 Designations 6 4.1 Material . 6 4.2 Material
14、 condition 6 4.3 Product . 7 5 Ordering information . 8 6 Requirements . 9 6.1 Composition . 9 6.2 Mechanical properties . 10 6.3 Electrical properties 10 6.4 Dimensions 10 6.5 Ductility . 10 6.6 Surface condition 10 7 Sampling . 11 7.1 General . 11 7.2 Analysis 11 7.3 Mechanical, electrical and tin
15、 coating tests . 11 8 Test methods . 11 8.1 Analysis 11 8.2 Tensile test . 11 8.3 Ductility test . 12 8.4 Electrical resistivity test . 12 8.5 Assessment of tin coatings 12 8.6 Retests 12 8.7 Rounding of results . 12 9 Declaration of conformity and inspection documentation 13 9.1 Declaration of conf
16、ormity . 13 9.2 Inspection documentation 13 10 Marking, packaging, labelling 13 Annex A (informative) Characteristics of coppers for electrical purposes . 20 A.1 General grouping of copper types . 20 A.2 General characteristics . 20 A.3 Particular characteristics 20 Bibliography 22 Tables Table 1 Co
17、mposition of Cu-ETP1 (CW003A) and Cu-OF1 (CW007A) . 14 Table 2 Composition of Cu-ETP (CW004A), Cu-FRHC (CW005A) and Cu-OF (CW008A) 15 Table 3 Mechanical properties of plain wire 16 Table 4 Mechanical properties of tinned wire 17 DIN EN 13602:2013-09 EN 13602:2013 (E) 3 Table 5 Electrical properties
18、(at 20 C) 18 Table 6 Tolerances on diameter 19 Table 7 Requirements of coatings . 19 Table 8 Number of bends for annealed wire 19 Table 9 Number of bends for hard drawn wire 19 Table A.1 Particular characteristics of copper grades for electrical purposes . 21 DIN EN 13602:2013-09 EN 13602:2013 (E) 4
19、 Foreword This document (EN 13602:2013) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at t
20、he latest by December 2013, and conflicting national standards shall be withdrawn at the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any
21、 or all such patent rights. This document supersedes EN 13602:2002. In comparison with EN 13602:2002, the following changes were made: Terms have been modified. Normative references have been updated. Editorial modifications have been made. Within its programme of work, Technical Committee CEN/TC 13
22、3 requested CEN/TC 133/WG 4 “Extruded and drawn products, forgings and scrap“ to prepare the following revision of the standard: EN 13602:2002, Copper and copper alloys Drawn, round copper wire for the manufacture of electrical conductors. The products specified in this European Standard are those w
23、hich are especially suitable for electrical purposes, i.e. with specified electrical properties. Drawn round wire for general purposes is specified in EN 12166. This is one of a series of European Standards for copper products for electrical purposes. Other copper products are specified as follows:
24、EN 13599, Copper and copper alloys Copper plate, sheet and strip for electrical purposes EN 13600, Copper and copper alloys Seamless copper tubes for electrical purposes EN 13601, Copper and copper alloys Copper rod, bar and wire for general electrical purposes EN 13604, Copper and copper alloys Sem
25、iconductor devices, electronic and vacuum products made from high conductivity copper EN 13605, Copper and copper alloys Copper profiles and profiled wire for electrical purposes According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bo
26、und to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug
27、al, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13602:2013-09 EN 13602:2013 (E) 5 1 Scope This European Standard specifies the composition, property requirements including electrical properties, and dimensional tolerances for drawn round copper wire
28、 from 0,04 mm up to and including 5,0 mm for the manufacture of electrical conductors intended for the production of bare and insulated cables and flexible cords. This standard covers plain or tinned, single or multiline, annealed or hard drawn wire. It does not include wire for enamelling (winding
29、wire, magnet wire), for electronic application and for contact wire for electric traction. The sampling procedures, the test methods for verification of conformity to the requirements of this standard and the delivery conditions are also specified. NOTE Due to the thermal and/or mechanical treatment
30、 involved in cablemaking processes, the properties of conductors in the final cable or cord differ from those of the original wire supplied. Requirements for conductors taken from cable or cord are given in appropriate cable standards. 2 Normative references The following documents, in whole or in p
31、art, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 610, Tin and tin alloys Ingot tin EN 1655, Co
32、pper and copper alloys Declarations of conformity EN 1976, Copper and copper alloys Cast unwrought copper products EN 10204, Metallic products Types of inspection documents EN 13603, Copper and copper alloys Test methods for assessing protective tin coatings on drawn round copper wire for electrical
33、 purposes EN ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1) IEC 60468, Method of measurement of resistivity of metallic materials ISO 1811-2, Copper and copper alloys Selection and preparation of samples for chemical analysis Part 2: Sampling o
34、f wrought products and castings ISO 4739, Wrought copper and copper alloy products Selection and preparation of specimens and test pieces for mechanical testing ISO 7801, Metallic materials Wire Reverse bend test ISO 7802, Metallic materials Wire Wrapping test DIN EN 13602:2013-09 EN 13602:2013 (E)
35、6 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 wire wound product of uniform cross-section along its whole length Note 1 to entry: Rectangles may have round or sharp corners. SOURCE: EN 12166:2011, 3.1 3.2 multiline wire number of wires of
36、 the same nominal diameter and material condition wound at the same time on the same spool with the wires having a maximum of one twist per revolution of the spool Note 1 to entry: Generally, the wires are drawn simultaneously on the same machine. 3.3 deviation from circular form difference between
37、the maximum and the minimum diameters measured at any one cross-section of a round product SOURCE: EN 12163:2011, 3.2 4 Designations 4.1 Material 4.1.1 General The material is designated either by symbol or by number (see Table 1 and Table 2). 4.1.2 Symbol The material symbol designation is based on
38、 the designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation system given in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material
39、number designation is in accordance with the system given in EN 1412. 4.2 Material condition For the purposes of this standard, the following designations, which are in accordance with the system given in EN 1173, apply for the material condition: R. Material condition designated by the minimum valu
40、e of tensile strength requirement for the product with mandatory tensile strength requirements; A. Material condition designated by the minimum value of elongation requirement for the product with mandatory elongation requirements. DIN EN 13602:2013-09 EN 13602:2013 (E) 7 Exact conversion between th
41、e material conditions designated R. and A. is not possible. Material condition is designated by only one of the above designations. 4.3 Product The product designation provides a standardised pattern of designation from which a rapid and unequivocal description of a product can be conveyed in commun
42、ication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The product designation for products to this standard shall consi
43、st of: a) denomination (wire); b) number of this European Standard (EN 13602); c) material designation, either symbol or number (see Table 1 and Table 2); d) material condition designation (see Table 3 and Table 4); e) surface condition: plain (P) or tinned (grade A, B or C, see Table 7); f) nominal
44、 dimensions: 1) single wire (S): diameter; 2) multiline wire (M): number of wires and diameter; g) form of delivery: coil (Y) or spool (Z). The derivation of a product designation is shown in Example 1. EXAMPLE 1 Plain single wire Drawn round wire for electrical purposes conforming to this standard,
45、 in material designated either Cu-ETP1 or CW003A, in material condition A022, produced as a plain single wire, nominal diameter 0,4 mm, in coils, will be designated as follows: Wire EN 13602 Cu-ETP1 A022 P S0,4 Y or Wire EN 13602 CW003A A022 P S0,4 Y Denomination Number of this European Standard Mat
46、erial designation Material condition designation Surface condition Nominal dimension Form of delivery DIN EN 13602:2013-09 EN 13602:2013 (E) 8EXAMPLE 2 Plain multiline wire Drawn round wire for electrical purposes conforming to this standard, in material designated either Cu-ETP or CW004A, in materi
47、al condition A020, produced as plain multiline wire of 7 wires, nominal diameter 0,4 mm, in coils, will be designated as follows: Wire EN 13602 Cu-ETP A020 P M7 0,4 Y or Wire EN 13602 CW004A A020 P M7 0,4 Y EXAMPLE 3 Tinned single wire Drawn round wire for electrical purposes conforming to this stan
48、dard, in material designated either Cu-OF1 or CW007A, in material condition A024, produced as tinned grade B single wire, nominal diameter 1,2 mm, in coils, will be designated as follows: Wire EN 13602 Cu-OF1 A024 B S1,2 Y or Wire EN 13602 CW007A A024 B S1,2 Y EXAMPLE 4 Tinned multiline wire Drawn r
49、ound wire for electrical purposes conforming to this standard, in material designated either Cu-FRHC or CW005A, in material condition A018, produced as tinned grade C, multiline wire of 10 wires, nominal diameter 0,5 mm, on spools, will be designated as follows: Wire EN 13602 Cu-FRHC A018 C M10 0,5 Z or Wire EN 13602 CW005A A018 C M10 0,5 Z 5 Ordering information In order to facilitate the enquiry, order a
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1