1、September 2013 Translation by DIN-Sprachendienst.English price group 13No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).
2、ICS 77.150.30!%)English version EN 13605:2013,English translation of DIN EN 13605:2013-09Kupfer und Kupferlegierungen Profile und profilierte Drhte aus Kupfer fr die Anwendung in der Elektrotechnik;Englische Fassung EN 13605:2013,Englische bersetzung von DIN EN 13605:2013-09Cuivre et alliages de cui
3、vre Profils et fils profils en cuivre pour usages lectriques;Version anglaise EN 13605:2013,Traduction anglaise de DIN EN 13605:2013-09SupersedesDIN EN 13605:2002-10 andDIN EN 13605 Corrigendum1:2005-04www.beuth.deDocument comprises 29 pagesIn case of doubt, the German-language original shall be con
4、sidered authoritative.08.13DIN EN 13605:2013-09 2 A comma is used as the decimal marker. National foreword This document (EN 13605:2013) has been prepared by Technical Committee CEN/TC 133 “Copper and copper alloys” (Secretariat: DIN, Germany). The responsible German body involved in its preparation
5、 was the Normenausschuss Nichteisenmetalle (Nonferrous Metals Standards Committee), Working Committee NA 066-02-04 AA Strangpress- und Zieherzeugnisse. Amendments This standard differs from DIN EN 13605:2002-10 and DIN EN 13605 Corrigendum 1:2005-04 as follows: a) new materials Cu-ETP1 (CW003A) and
6、Cu-OF1 (CW007A) have been added (see Table 1); b) mass tolerances have been changed; c) some editorial notes have been included; d) Annex B has been deleted. Previous editions DIN VDE 500 = DIN 40500: 1934x-04 DIN 40500-3: 1959-06, 1962-10, 1970-09, 1980-04 DIN 17674-3: 1963-06 DIN 17674-4: 1963-06
7、DIN 17674-5: 1963-06 DIN EN 13605: 2002-10 DIN EN 13605 Corrigendum 1:2005-04 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13605 June 2013 ICS 77.150.30 Supersedes EN 13605:2002English Version Copper and copper alloys - Copper profiles and profiled wire for electrical purposes Cuivre et alli
8、ages de cuivre - Profils et fils profils en cuivre pour usages lectriques Kupfer und Kupferlegierungen - Profile und profilierte Drhte aus Kupfer fr die Anwendung in der ElektrotechnikThis European Standard was approved by CEN on 25 April 2013. CEN members are bound to comply with the CEN/CENELEC In
9、ternal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to a
10、ny CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official
11、versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norw
12、ay, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in a
13、ny form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13605:2013: EEN 13605:2013 (E) 2 Contents Page Foreword 4 1 Scope 6 2 Normative references 6 3 Terms and definitions .6 4 Designations 7 4.1 Material .7 4.2 Material condition 7 4.3 Product .7 5 Ordering information .8
14、 6 Requirements 10 6.1 Composition 10 6.2 Mechanical properties 10 6.3 Electrical properties . 10 6.4 Freedom from hydrogen embrittlement . 10 6.5 Drawings 10 6.6 Dimensions and tolerances . 10 6.7 Form of delivery of profiled wire . 14 6.8 Mass tolerances 14 6.9 Surface condition 14 7 Sampling 15 7
15、.1 General . 15 7.2 Analysis . 15 7.3 Mechanical, electrical and hydrogen embrittlement tests 15 8 Test methods . 15 8.1 Analysis . 15 8.2 Tensile test 15 8.3 Hardness test 15 8.4 Electrical test . 16 8.5 Hydrogen embrittlement test . 16 8.6 Retests . 16 8.7 Rounding of results 16 9 Declaration of c
16、onformity and inspection documentation . 17 9.1 Declaration of conformity 17 9.2 Inspection documentation . 17 10 Marking, packaging, labelling 17 Annex A (informative) Characteristics of coppers for electrical purposes 25 Bibliography . 27 Figures Figure 1 Profile within a circumscribing circle . 1
17、1 Figure 2 Cross-sectional dimensions 11 Figure 3 Twist of a profile 12 Figure 4 Indication of flatness on a U-Profile 13 Figure 5 Indication of flatness on a H-Profile 13 Figure 6 Indication of angularity 13 Figure 7 Indication of perpendicularity 13 Figure 8 Indication of straightness tolerances 1
18、4 DIN EN 13605:2013-09 EN 13605:2013 (E) 3 Tables Table 1 Composition of unalloyed copper grades . 18 Table 2 Composition of copper grades 19 Table 3 Mechanical properties . 20 Table 4 Electrical properties (at 20 C) 21 Table 5 Tolerances for dimensions b and h, ratio bmax.or hmax.to smin. 20 : 1 21
19、 Table 6 Tolerances for dimensions b and h, ratio bmax.or hmax.to smin. 20 : 1 22 Table 7 Thickness tolerances 22 Table 8 Radius tolerances . 22 Table 9 Maximum radii of sharp corners . 22 Table 10 Twist tolerances coefficient f 23 Table 11 Straightness tolerances for profiles 23 Table 12 Tolerances
20、 on “as manufactured“ lengths 23 Table 13 Tolerances on “fixed“ lengths . 24 Table 14 Sampling rate 24 Table A.1 Particular characteristics of coppers for electrical purposes . 26 DIN EN 13605:2013-09 EN 13605:2013 (E) 4 Foreword This document (EN 13605:2013) has been prepared by Technical Committee
21、 CEN/TC 133 “Copper and copper alloys”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2013 and conflicting national standards shall be withdrawn
22、 at the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13605:2002. In comparison
23、 with EN 13605:2002, the following significant technical changes have been made: Cu-ETP1 (CW003A), Cu-OF1 (CW007A), Cu-OFE (CW009A) and Cu-PHCE (CW022A) have been added (Table 1). The impurity content (other materials) in the chemical composition of Cu-FRHC (CW005A) has been modified in accordance w
24、ith EN 1976:2012 and EN 1977:2013. Mass tolerances have been changed. Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 4 “Extruded and drawn products, forgings and scrap“ to revise the following standard: EN 13605:2002, Copper and copper alloys Copper profiles and
25、 profiled wire for electrical purposes. The products specified in this European Standard are those which are especially suitable for electrical purposes, i.e. with specified electrical properties. Profiles for general purposes are specified in EN 12167. Annex A (informative) gives guidance on the ch
26、aracteristics of coppers for electrical purposes. This is one of a series of European Standards for copper products for electrical purposes. Other copper products are specified as follows: EN 13599, Copper and copper alloys Copper plate, sheet and strip for electrical purposes EN 13600, Copper and c
27、opper alloys Seamless copper tubes for electrical purposes EN 13601, Copper and copper alloys Copper rod, bar and wire for general electrical purposes EN 13602, Copper and copper alloys Drawn, round copper wire for the manufacture of electrical conductors EN 13604, Copper and copper alloys Semicondu
28、ctor devices, electronic and vacuum products made from high conductivity copper According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republi
29、c, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, DIN EN 13605:2013-09 EN 13605:2013 (E) 5 Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerlan
30、d, Turkey and the United Kingdom. DIN EN 13605:2013-09 EN 13605:2013 (E) 6 1 Scope This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper profiles and profiled wire for electrical purposes, which would
31、 fit within a circumscribing circle of maximum 180 mm diameter. The sampling procedures, the test methods for verification of conformity to the requirements of this standard, and the delivery conditions are also specified. 2 Normative references The following documents, in whole or in part, are norm
32、atively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1655, Copper and copper alloys Declarations of conformity
33、EN 1976, Copper and copper alloys Cast unwrought copper products EN 10204, Metallic products Types of inspection documents EN ISO 2626, Copper Hydrogen embrittlement test (ISO 2626) EN ISO 6506-1, Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1) EN ISO 6507-1, Metallic mater
34、ials Vickers hardness test Part 1: Test method (ISO 6507-1) EN ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature (ISO 6892-1) EN ISO 7438, Metallic materials Bend test (ISO 7438) 3 Terms and definitions For the purposes of this document, the following terms an
35、d definitions apply. 3.1 profile wrought product of uniform cross-section along its whole length, supplied in straight lengths Note 1 to entry: It may be solid or hollow: if solid, the contour of its cross-section is complex; if hollow, the external contour and/or the internal contour of its cross-s
36、ection is (are) complex. 3.2 profiled wire particular type of wire, i.e. a wrought product of uniform cross-section along its whole length, supplied in coiled form Note 1 to entry: It may be solid or hollow: if solid, the contour of its cross-section is complex; if hollow the external contour and/or
37、 the internal contour of its cross-section is (are) complex. DIN EN 13605:2013-09 EN 13605:2013 (E) 7 3.3 circumscribing circle smallest circle which completely encloses the contour of the cross-sections of the profile or profiled wire 4 Designations 4.1 Material 4.1.1 General The material is design
38、ated either by symbol or by number (see Table 1 and Table 2). 4.1.2 Symbol The material symbol designation is based on the designation system given in ISO 1190-1. NOTE Although material symbol designations used in this standard might be the same as those in other standards using the designation syst
39、em given in ISO 1190-1, the detailed composition requirements are not necessarily the same. 4.1.3 Number The material number designation is in accordance with the system given in EN 1412. 4.2 Material condition For the purposes of this standard, the following designations, which are in accordance wi
40、th the system given in EN 1173, apply for the material condition: D Material condition for the product as drawn without specified mechanical properties; H. Material condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements; R. Material con
41、dition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength, 0,2 % proof strength and elongation requirements. Products in the H. condition may be specified to Vickers or Brinell hardness. The material condition designation H. is the same fo
42、r both hardness test methods. Exact conversion between the material conditions designated H. and R. is not possible. Material condition is designated by only one of the above designations. 4.3 Product The product designation provides a standardised pattern of designation from which a rapid and unequ
43、ivocal description of a product can be conveyed in communication. It provides mutual comprehension at the international level with regard to products which meet the requirements of the relevant European Standard. The product designation is no substitute for the full content of the standard. The prod
44、uct designation for products to this standard shall consist of: a) denomination (profile or profiled wire); DIN EN 13605:2013-09 EN 13605:2013 (E) 8 b) number of this European Standard (EN 13605); c) material designation, either symbol or number (see Table 1 and Table 2); d) material condition desig
45、nation (see Table 3); e) for profiles or profiled wire, a number, or the number of a fully dimensioned and toleranced drawing; f) for profiles, length, either as manufactured length (ML) or fixed length (FL); g) for profiled wire, form of delivery: coil (Y) or spool (Z). The derivation of a product
46、designation is shown in Example 1 and another typical product designation is shown in Example 2. EXAMPLE 1 Profile for electrical purposes conforming to this standard, in material designated either Cu-ETP or CW004A, in material condition H080, drawing number XY000, manufactured length 3 000 mm, will
47、 be designated as follows: Profile EN 13605 Cu-ETP H080 XY000 3000ML or Profile EN 13605 CW004A H080 XY000 3000ML Denomination Number of this European Standard Material designation Material condition designation Drawing number Length in millimetres EXAMPLE 2 Profiled wire for electrical purposes con
48、forming to this standard, in material designated either CuAg0,10 or CW013A in material condition H035, drawing number BC000, in coils, will be designated as follows: Profiled wire EN 13605 CuAg0,10 H035 BC000 Y or Profiled wire EN 13605 CW013A H035 BC000 Y 5 Ordering information In order to facilita
49、te the enquiry, order and confirmation of order procedures between the purchaser and the supplier, the purchaser shall state on his enquiry and order the following information: a) quantity of product required (mass, number of profiles or number of coils or spools); b) denomination (profile or profiled wire); c) number of this European Standard (EN 13605); d) material designation (see Table 1 and Table 2); e) material conditio
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1