DIN EN 13617-3-2012 Petrol filling stations - Part 3 Safety requirements for construction and performance of shear valves German version EN 13617-3 2012《加油站 第3部分 剪阀的建造和性能的安全要求》.pdf

1、May 2012 Translation by DIN-Sprachendienst.English price group 11No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 75

2、.200!$|=?“1892628www.din.deDDIN EN 13617-3Petrol filling stations Part 3: Safety requirements for construction and performance of shearvalvesEnglish translation of DIN EN 13617-3:2012-05Tankstellen Teil 3: Sicherheitstechnische Anforderungen an Bau- und Arbeitsweise vonAbscherventilenEnglische berse

3、tzung von DIN EN 13617-3:2012-05Stations-service Partie 3: Exigences de scurit relatives la construction et aux performances desraccords de scuritTraduction anglaise de DIN EN 13617-3:2012-05SupersedesDIN EN 13617-3:2004-11www.beuth.deDocument comprises 20 pagesIn case of doubt, the German-language

4、original shall be considered authoritative.04.12 DIN EN 13617-3:2012-05 2 A comma is used as the decimal marker. National foreword This standard has been prepared by Technical Committee CEN/TC 393 “Equipment for storage tanks and for service stations” (Secretariat: DIN, Germany). The responsible Ger

5、man body involved in its preparation was the Normenausschuss Tankanlagen (Tank Installations Standards Committee), Working Committee NA 104-02-06 AA Abgabeeinrichtungen an Tankstellen. Amendments This standard differs from DIN EN 13617-3:2004-11 as follows: a) a new note has been added at the end of

6、 the scope; b) an informative Annex C regarding environmental aspects has been included; c) normative references have been updated. Previous editions DIN EN 13617-3: 2004-11 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13617-3 March 2012 ICS 75.200 Supersedes EN 13617-3:2004English Version P

7、etrol filling stations - Part 3: Safety requirements for construction and performance of shear valves Stations-service - Partie 3: Exigences de scurit relatives la construction et aux performances des raccords de scurit Tankstellen - Teil 3: Sicherheitstechnische Anforderungen an Bau- und Arbeitswei

8、se von Abscherventilen This European Standard was approved by CEN on 28 January 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists

9、and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under th

10、e responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germ

11、any, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR

12、 NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13617-3:2012: EEN 13617-3:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms

13、 and definitions .54 Explosion protection measures .65 Construction .65.1 General requirements 65.2 Specific requirements .75.3 Classes of construction 75.4 Threads .76 Physical properties 77 Operational requirements .88 Tests 88.1 General 88.2 Type tests .88.3 Production acceptance tests 88.4 Routi

14、ne tests 99 Information for use 99.1 General 99.2 Marking and instruction 9Annex A (normative) Instructions Guide for items to be included in manufacturers installation and user manual . 11Annex B (normative) Test methods 12B.1 General requirements . 12B.2 Pressure test (routine test) 12B.3 Main val

15、ve test (routine test) . 12B.4 Pressure relief valve test (routine test) 12B.5 Fuel preconditioning (type test) 13B.6 Pressure test (type test) . 13B.7 Main valve test (type test) 13B.8 Check valve test (class I only) (type test) 13B.9 Pressure relief valve test (class I only) (type test) 14B.10 The

16、rmal link test 1 (class I and class II only) (type test and production acceptance test) . 14B.11 Thermal link test 2 (class I and class II only) (type test and production acceptance test) . 14B.12 Main valve closure test (type test and production acceptance test) . 14B.13 Main valve closure test (ty

17、pe test and production acceptance test) . 15Annex C (informative) Environmental aspects 16Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 94/9/EC . 18DIN EN 13617-3:2012-05 EN 13617-3:2012 (E) 3 Foreword This document (EN 13617-3:2012

18、) has been prepared by Technical Committee CEN/TC 393 “Equipment for tanks and filling stations”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September

19、 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent

20、rights. This document supersedes EN 13617-3:2004. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA,

21、which is an integral part of this document. According to edition EN 13617-3:2004 the following fundamental changes are given: a new note at the end of the scope: Fuels other than of Explosion Group IIA are excluded from this European Standard added; informative Annex C concerning environmental aspec

22、ts added. The present standard is composed of the following parts: Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units; Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers

23、; Part 3: Safety requirements for construction and performance of shear valves; Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following c

24、ountries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, S

25、lovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 13617-3:2012-05 EN 13617-3:2012 (E) 4 Introduction The function of the shear valve is to prevent continuous liquid or vapour release in the event of impact or fire DIN EN 13617-3:2012-05 EN 13617-3:2012 (E) 5 1 Scope This Eur

26、opean Standard specifies safety and environmental requirements for the construction and performance of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at petrol filling stations and used to dispense liquid fuels into the tanks of motor vehicles, b

27、oats and light aircraft and into portable containers at flow rates up to 200 l min-1. The requirements apply to shear valves at ambient temperatures from 20 C to +40 C with the possibility for an extended temperature range. It pays particular attention to mechanical and hydraulic characteristics. NO

28、TE 1 This European Standard does not apply to equipment for use with liquefied petroleum gas (LPG) or liquefied natural gas (LNG) or compressed natural gas (CNG). NOTE 2 Fuels other than of Explosion Group IIA are excluded from this European Standard. 2 Normative references The following documents,

29、in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 9761, Underground tanks of gl

30、ass-reinforced plastics (GRP) Horizontal cylindrical tanks for the non-pressure storage of liquid petroleum based fuels Part 1: Requirements and test methods for single wall tanks EN 1127-1, Explosive atmospheres Explosion prevention and protection Part 1: Basic concepts and methodology EN 134631:20

31、09, Non-electrical equipment for use in potentially explosive atmospheres Part 1: Basic method and requirements EN 13617-1:2012, Petrol filling stations Part 1: Safety requirements for the construction and performance of metering pumps, dispensers and remote pumping units EN 60079-0, Explosive atmos

32、pheres Part 0: Equipment General requirements EN ISO 1182, Reaction to fire tests for products Non-combustibility test (ISO 1182) ISO 71, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designations 3 Terms and definitions For the purposes of this

33、document, the terms and definitions given in prEN 136171:2010 and the following apply. 3.1 main valve (liquid) normally open valve on the inlet side, closing when the shear valve operates 3.2 main valve (vapour) normally open valve on the outlet side, closing when the shear valve operates DIN EN 136

34、17-3:2012-05 EN 13617-3:2012 (E) 6 3.3 pressure relief valve valve to allow liquid to return to the pipework below the dispenser if pressure in the dispenser increases beyond a defined level 3.4 separation zone designed to be the first section of the shear valve to fracture when stressed 3.5 mechani

35、cal link device to activate the closing mechanism automatically to stop the flow of liquid when the shear valve breaks 3.6 thermal detector device to activate the closing mechanism automatically to stop the flow of liquid when the temperature in the vicinity of the shear valve exceeds the operating

36、temperature 3.7 test plug device to allow pressure testing of associated pipework 3.8 mounting point rigid attachment facility on the inlet and outlet sections of the shear valve 4 Explosion protection measures 4.1 Explosion protection measures shall be taken in accordance with EN 1127-1 and Annex B

37、 of EN 13617-1:2012. 4.2 The shear valve shall be explosion protected and shall be Category 2 in accordance with EN 134631. When a shear valve has a vapour path, the vapour path shall be category 1 in accordance with EN 134631. The shear valve shall fulfil the requirements for temperature Class T3 a

38、nd Group IIA to EN 60079-0 or EN 134631. 5 Construction 5.1 General requirements 5.1.1 All electrical and non-electrical equipment and components, intended for use in potentially explosive atmospheres, shall be designed and constructed according to good engineering practice and in conformity with th

39、e required categories for Group II equipment to ensure avoidance of any ignition source. To classify the category of the equipment it shall be subjected to an ignition hazard assessment in accordance with 5.2 of EN 13463-1:2009. 5.1.2 All materials used in the construction shall be chemically and di

40、mensionally stable under known service conditions. Materials likely to come into contact with fuels in both liquid and vapour phases shall be resistant to attack by these fuels. Conformity shall be demonstrated by testing in accordance with Clause 8. 5.1.3 Light alloys when used shall conform to the

41、 requirements of 6.4.4.2 of EN 134631:2009. If other specifications for explosion protected equipment impose more stringent requirements then the more stringent requirement shall apply. 5.1.4 All components shall be of corrosion resistant material or shall be provided with a corrosion resistant prot

42、ective coating. 5.1.5 Outside surfaces likely to be handled shall be free of sharp edges. DIN EN 13617-3:2012-05 EN 13617-3:2012 (E) 7 5.2 Specific requirements 5.2.1 Means shall be provided to connect the shear valve to input and output pipework. The means selected shall not fail at forces less tha

43、n the design shear force of the shear valve. 5.2.2 The shear valve shall be so designed that after fracture of the weak section, the input and output sections shall be completely decoupled. 5.2.3 The shear valve shall not have a means to prevent the main valve from closing completely when it is oper

44、ated by the weak section or by the thermal detector. 5.2.4 The thermal detector shall be so constructed that when it operates the main valve closes. 5.2.5 Shear valves for liquids may include a manual means of closing the main valve (liquid) for maintain purposes. 5.2.6 Test plugs, where fitted to s

45、hear valves in liquid containment systems, shall be on the inlet side of the main valve. 5.3 Classes of construction Shear valves are classified in accordance with Table 1. Table 1 Classes of construction Valve type Class I II III Main valve Yes Yes Yes Thermal detector Yes Yes No Check valve Yes No

46、 No Pressure relief valve Yes No No Class I and II for liquid pressure systems, Class III for vapour systems only. 5.4 Threads Input and output threads shall be in accordance with ISO 71. 6 Physical properties The physical properties of the shear valve shall conform to Table 2 when tested by the met

47、hods indicated. Table 2 Physical properties of shear valve Physical property Requirement Test method Fuel compatibility (preconditioning) Clause 5 B.5 Electrostatic properties 6.7 of EN 13463-1:2009 EN 13463-1 Fire resistance EN ISO 1182 EN ISO 1182 DIN EN 13617-3:2012-05 EN 13617-3:2012 (E) 8 7 Ope

48、rational requirements The shear valve shall conform to the operational requirements according to Table 3 and Table 4 when tested by the methods indicated. Table 3 Operational requirements Item Requirement Test methodHousing No quantifiable leakage, as evidenced by bubbles, or permanent deformation visible to an eye with normal visual acuity. B.2 Main valve No quantifiable leakage, as evidenced by bubbles, or permanent