DIN EN 14218-2003 Hexagon nuts with flange - Fine pitch thread (ISO 10663 1999 modified) German version EN 14218 2003《六角法兰面螺母 细牙螺纹》.pdf

1、ICS 21.060.20Sechskantmuttern mit Flansch Feingewinde (ISO 10663 : 1999, modifiziert)European Standard EN 14218 : 2003 has the status of a DIN Standard.A comma is used as the decimal marker.National forewordThis standard has been prepared by CEN/TC 185 Threaded and non-threaded mechanical fasteners

2、andaccessories (Secretariat: Germany).The responsible German body involved in its preparation was the Normenausschuss MechanischeVerbindungselemente (Fasteners Standards Committee), Technical Committee Schrauben und Muttern mitAuenantrieb.The DIN Standards corresponding to the International Standard

3、s referred to in clause 2 of the EN are asfollows:ISO 724 DIN ISO 724ISO 965-2 DIN ISO 965-2ISO 8992 DIN ISO 8992Ref. No. DIN EN 14218 : 2003-09English price group 07 Sales No. 110701.04DEUTSCHE NORM September 2003EN 14218Continued overleaf.EN comprises 8 pages. No part of this standard may be repro

4、duced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).Hexagon nuts with flangeFine pitch thread(ISO 10663 : 1999, modified)English version of DIN EN 14218English

5、 versionICS 21.060.20Hexagon nuts with flangeFine pitch thread(ISO 10663 : 1999, modified) 2003. CEN All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.Ref. No. EN 14218 : 2003 ESechskantmuttern mit Flansch Fein-gewinde (ISO 10663 : 1999, modifi-ziert)

6、This European Standard was approved by CEN on 2003-02-14.CEN members are bound to comply with the CEN/CENELEC Internal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists and bibliographical references c

7、oncerning such national stand-ards may be obtained on application to the Management Centre or to anyCEN member.The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own la

8、nguage and notified to the Management Centre hasthe same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland,Ireland, Italy, Luxembourg, Malta, the Netherlands, Norway, Portu

9、gal, Slovakia,Spain, Sweden, Switzerland, and the United Kingdom.EN 14218April 2003Management Centre: rue de Stassart 36, B-1050 BrusselsEuropean Committee for StandardizationComit Europen de NormalisationEuropisches Komitee fr NormungEcrous hexagonaux embasecylindro-trononique Filetage pasfin (ISO

10、10663 : 1999, modifie)G50G61G67G65 G32G45G4E G31G34G32G31G38 G3A G32G30G30G33ForewordThis document (EN 14218:2003) has been prepared by Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories“, the Secretariat of which is held by DIN.This European Standard shal

11、l be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latestby October 2003.In accordance with the CEN/CENELEC Internal Regulations, the national standards

12、 organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United K

13、ingdom.Endorsement noticeThe text of International Standard ISO 10663:1999 was approved by CEN as a European Standard with agreedcommon modifications as given below.Nuts in accordance with this European Standard correspond to those specified in the International Standard ISO10663:1999 with the excep

14、tion that the width across flats for M10 is 16 mm (instead of 15 mm) and that the prop-erty class 9 was deleted. Moreover, the option for surface coatings according to EN ISO 10683 was added.G50G61G67G65 G33G45G4E G31G34G32G31G38 G3A G32G30G30G331 ScopeThis European Standard specifies the characteri

15、stics of hexagon nuts with flange, with metric fine pitch thread, withnominal thread diameters from 8 mm up to and including 20 mm, in product grade A for d 16 mm and productgrade B for d 16 mm and with property classes 8, 10, 12 and A2-70.If, in special cases, specifications other than those listed

16、 in this European Standard are required, they should beselected from existing European and International Standards, for example ISO 724, EN ISO 898-6, ISO 965-2,EN ISO 3506-2.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.

17、Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undat

18、ed references the latest edition of thepublication referred to applies (including amendments).EN 493, Fasteners Surface discontinuities Nuts.EN 20225, Fasteners Bolts, screws, studs and nuts Symbols and designations of dimensions (ISO 225:1983).EN ISO 898-6, Mechanical properties of fasteners Part 6

19、: Nuts with specified proof load values Fine pitchthread (ISO 898-6:1994).EN ISO 3269, Fasteners Acceptance inspection (ISO 3269:2000).EN ISO 3506-2, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 2: Nuts(ISO 3506-2:1997).EN ISO 4042, Fasteners Electroplated coatings (IS

20、O 4042:1999).EN ISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C(ISO 4759-1:2000).EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings (ISO 10683:2000).ISO 724, ISO general purpose metric screw threads Basic dimensions.ISO 965-2

21、, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for general purposeexternal and internal screw threads Medium quality.ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts.G50G61G67G65 G34G45G4E G31G34G32G31G38 G3A G32G30G30G333 DimensionsSee figure

22、 1 and table 1.Symbols and designations of dimensions are specified in EN 20225.KeyamWis the wrenching height; see note to table 1.b = 90 to 120c = 15 to 30 d = 15 to 25ec is measured at dwmin.fEdge contour optionalFigure 1G50G61G67G65 G35G45G4E G31G34G32G31G38 G3A G32G30G30G33Table 1 - DimensionsDi

23、mensions in millimetresThread d x PaM81M101,25M101M121,25M121,5(M141,5)bM161,5 M201,5c min. 1,2 1,5 1,8 2,1 2,4 3min. 8,00 10,00 12 14,0 16,0 20,0damax. 8,75 10,80 13 15,1 17,3 21,6dcmax. 17,9 21,8 26,0 29,9 34,5 42,8dwmin. 15,8 19,6 23,8 27,6 31,9 39,9e min. 14,38 17,77 20,03 23,36 26,75 32,95max.

24、8,00 10,00 12,00 14,0 16,0 20,0mmin. 7,64 9,64 11,57 13,3 15,3 18,7mwmin. 4,6 5,6 6,8 7,7 8,9 10,7max. 13,00 16,00 18,00 21,00 24,00 30,00smin. 12,73 15,73 17,73 20,67 23,67 29,16rcmax. 0,5 0,6 0,7 0,9 1 1,2NOTE If the product passes the gauging given in annex A, the requirements for dimensions e, c

25、 and mware satisfied.aP is the pitch of the thread.bThe size in brackets should be avoided if possible.cRadius r applies both at the corners and at the flats of the hexagon.G50G61G67G65 G36G45G4E G31G34G32G31G38 G3A G32G30G30G334 Specifications and relevant European or International StandardsSee tab

26、le 2.Table 2 Specifications and relevant European or International StandardsMaterial Steel Stainless steelGeneralrequirementsInternationalStandardISO 8992Tolerance 6HThreadInternationalStandardsISO 724, ISO 965-2Property class 8 10 12Style decisivefor mechanicalpropertiesad 16 mmstyle 2d 16 mmstyle

27、1style 2d 16 mmbstyle 2A2-70MechanicalpropertiesEuropeanStandardsEN ISO 898-6 EN ISO 3506-2Product graded 16 mm: Ad 16 mm: BTolerancesEuropeanStandardEN ISO 4759-1FinishAs processedRequirements for electroplating are covered in EN ISO 4042.Requirements for non-electrolytically applied zinc flakecoat

28、ings are covered in EN ISO 10683.PlainSurface discontinuities Limits for surface discontinuities are covered in EN 493.Acceptability For acceptance procedure, see EN ISO 3269.aBased on the nut height (dimension mmin) nuts to this standard are of style 2. However, since for style 2, EN ISO 898-6 does

29、not specifiy mechanical properties for all property classes and sizes as specified in this standard, in some cases nuts have tobe tested according to style 1.bFor d 16 mm property class 12 is not specified.5 DesignationEXAMPLE A hexagon nut with flange, with thread M12 x 1,25 and property class 10 i

30、s designated as follows:Hexagon nut with flange EN 14218 M12 x 1,25 10G50G61G67G65 G37G45G4E G31G34G32G31G38 G3A G32G30G30G33Annex A(normative)Gauging of hexagon flange nutsA.1 Recommended method for gauging of hexagon (see figure A.1 and table A.1)The nut shall be gauged using two plain ring gauges

31、, A and B, to demonstrate the coincidental acceptability ofhexagon height, corner fill and width across corners. Gauge A shall be placed over the nut and shall be seated on theflange. Gauge B shall be placed on the top of the nut normal to the nut axis. The two gauges shall not be in contact.A.2 Rec

32、ommended method for gauging of flange thickness (see figure A.1 and table A.1)Gauge C is a flat feeler or ring gauge. It is used to prove that the flange thickness at the junction with the hexagonportion is equal to or greater than specified values. The acceptance criterion is that gauge C shall fit

33、 under gauge Awithout contact when the nut is seated on a flat plate.Key1 Gauge A2 Gauge B3 Gauge CNOTE Wamin= etheoreticalWb max= emin 0,01 mmTamax= mw minFigure A.1G50G61G67G65 G38G45G4E G31G34G32G31G38 G3A G32G30G30G33Table A.1Dimensions in millimetresGauge A Gauge B Gauge CWa Ta WbTbWcTcNominalt

34、hreaddiameterd max. min. max. min. max. min. min. min. max. min.8101215,0218,4920,7915,0118,4820,784,605,606,804,595,596,7914,3717,7620,0214,3617,7520,014552024291,311,812,201,301,802,1914162024,2627,7234,6524,2527,7134,647,708,9010,707,698,8910,6923,3526,7432,9423,3426,7332,9366632,537452,552,963,702,542,953,69