DIN EN 14219-2003 Hexagon bolts with flange with metric fine pitch thread - Small series (ISO 15072 1999 modified) German version EN 14219 2003《米制细牙螺纹六角法兰面螺栓 小系列》.pdf

1、ICS 21.060.10Sechskantschrauben mit Flansch mit Feingewinde Leichte Reihe (ISO 15072 : 1999, modifiziert)European Standard EN 14219 : 2003 has the status of a DIN Standard.A comma is used as the decimal marker.National forewordThis standard has been prepared by CEN/TC 185 Threaded and non-threaded m

2、echanical fasteners andaccessories (Secretariat: Germany).The responsible German body involved in its preparation was the Normenausschuss MechanischeVerbindungselemente (Fasteners Standards Committee), Technical Committee Schrauben und Muttern mitAuenantrieb.The DIN Standards corresponding to the In

3、ternational Standards referred to in clause 2 of the EN are asfollows:ISO 724 DIN ISO 724ISO 965-2 DIN ISO 965-2ISO 8992 DIN ISO 8992Ref. No. DIN EN 14219 : 2003-09English price group 08 Sales No. 110801.04DEUTSCHE NORM September 2003EN 14219Continued overleaf.EN comprises 10 pages. No part of this

4、standard may be reproduced without the prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).Hexagon bolts with flange with metric fine pitch threadSmall series(ISO 15072 : 1999,

5、modified)English version of DIN EN 14219English versionICS 21.060.10Hexagon bolts with flange with metric fine pitch threadSmall series(ISO 15072 : 1999, modified) 2003. CEN All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.Ref. No. EN 14219 : 2003 ES

6、echskantschrauben mit Flansch mitFeingewinde Leichte Reihe(ISO 15072 : 1999, modifiziert)This European Standard was approved by CEN on 2003-02-14.CEN members are bound to comply with the CEN/CENELEC Internal Regulationswhich stipulate the conditions for giving this European Standard the status of an

7、ational standard without any alteration.Up-to-date lists and bibliographical references concerning such national stand-ards may be obtained on application to the Management Centre or to anyCEN member.The European Standards exist in three official versions (English, French, German).A version in any o

8、ther language made by translation under the responsibility of aCEN member into its own language and notified to the Management Centre hasthe same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, G

9、reece, Hungary, Iceland,Ireland, Italy, Luxembourg, Malta, the Netherlands, Norway, Portugal, Slovakia,Spain, Sweden, Switzerland, and the United Kingdom.EN 14219April 2003Management Centre: rue de Stassart 36, B-1050 BrusselsEuropean Committee for StandardizationComit Europen de NormalisationEuropi

10、sches Komitee fr NormungVis tte hexagonale embasecylindro-trononique pas fin Srietroite (ISO 15072 : 1999, modifie)G50G61G67G65 G32G45G4E G31G34G32G31G39 G3A G32G30G30G33ForewordThis document (EN 14219:2003) has been prepared by Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fa

11、steners and accessories“, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latestby

12、 October 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, M

13、alta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.Endorsement noticeThe text of the International Standard ISO 15072:1999 was approved by CEN as a European Standard with agreedcommon modifications as given below.Bolts in accordance with this European Sta

14、ndard correspond to those specified in the International StandardISO 15072:1999 with the exception that the width across flats for M12 is 16 mm (instead of 15 mm) and that theproperty class 9.8 was deleted. Moreover, the option for surface coatings according to ISO 10683 was added.G50G61G67G65 G33G4

15、5G4E G31G34G32G31G39 G3A G32G30G30G331 ScopeThis European Standard specifies the characteristics of hexagon bolts with flange with metric fine pitch thread,small series, with product grade A, with nominal thread diameters from 8 mm up to and including 16 mm and prop-erty classes 8.8, 10.9, 12.9 and

16、A2-70.If, in special cases, specifications other than those listed in this European Standard are required, they shall be se-lected from existing European and International Standards, for example ISO 724, ISO 888, EN ISO 898-1,ISO 965-2, EN ISO 3506-1.2 Normative referencesThis European Standard inco

17、rporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this Europ

18、eanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN 20225, Fasteners Bolts, screws, studs and nuts Symbols and designations of dimensions (ISO 225:1983).EN 26157-3, Fasteners Surf

19、ace discontinuities Part 3: Bolts, screws and studs for special requirements(ISO 6157-3:1988).EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws andstuds (ISO 898-1:1999).EN ISO 3269, Fasteners Acceptance inspection (ISO 3269:2000).EN ISO 3506

20、-1, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 1: Bolts, screws andstuds (ISO 3506-1:1997).EN ISO 4042, Fasteners Electroplated coatings (ISO 4042:1999).EN ISO 4753, Fasteners Ends of parts with external ISO metric screw thread (ISO 4753:1999).EN ISO 4759-1, Toleranc

21、es for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C(ISO 4759-1:2000).EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings (ISO 10683:2000).ISO 724, ISO general purpose metric screw threads Basic dimensions.ISO 965-2, ISO general purpose metric screw t

22、hreads Tolerances Part 2: Limits of sizes for general purposeexternal and internal screw threads Medium quality.ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts.G50G61G67G65 G34G45G4E G31G34G32G31G39 G3A G32G30G30G333 DimensionsDimensions shall be in accordance with figures

23、 1 to 4 and table 1.Symbols and designations of dimensions are specified in EN 20225.KeyaThe top of the head shall be either full form or indented at the manufacturers option and shall be either chamfered orrounded. The minimum diameter of the chamfer circle or start of rounding shall be equal to th

24、e maximum width across flats mi-nus 15 %. If the top of the head is indented, the periphery may be rounded.bEdge contour optional.cChamfered end (see EN ISO 4753).d = 15 to 30 ekw is the wrenching height; see the note to table 1.fIncomplete thread u 2 PFigure 1 Hexagon bolt with flange Full shank (s

25、tandard type)Tolerances in millimetresNOTE For other dimensions, see figure 1KeyaRounded or chamfered or conical.bd2is approximately equal to the pitch diameter (rolling diameter).Figure 2 Hexagon bolt with flange Reduced shank, type R (upon request)G50G61G67G65 G35G45G4E G31G34G32G31G39 G3A G32G30G

26、30G33Type F without undercut (upon request or optional) Type U with undercut (upon request or optional)Keyac is measured at dw min.b = 15 to 25cMaximum and minimum underhead fillet.dJunction of fillet with bearing surface to be a smooth blend.Figure 3 Hexagon bolt with flange Underhead configuration

27、 (bearing area)Figure 4 Hexagon bolt with flange threaded to the headG50G61G67G65 G36G45G4E G31G34G32G31G39 G3A G32G30G30G33Table 1 - DimensionsDimensions in millimetresThread size d PaM8 1M10 1M10 1,25M12 1,25M12 1,5(M14 1,5)bM16 1,5max. 3 3 4,5 4,5 4,5Amin. 1 1 1,5 1,5 1,5c22 26 30 34 38d28 32 36

28、40 44 b ref.e 57C min. 1,2 1,5 1,8 2,1 2,4F max. 9,2 11,2 13,7 15,7 17,7da TypesU max. 10 12,5 15,2 17,7 20,5dcmax. 17 20,8 24,7 28,6 32,8max. 8,00 10,00 12,00 14,00 16,00dsmin. 7,78 9,78 11,73 13,73 15,73dvmax. 8,8 10,8 12,8 14,8 17,2dwmin. 14,9 18,7 22,5 26,4 30,6E min. 10,95 14,26 17,62 19,86 23,

29、15K max. 8,5 9,7 12,1 12,9 15,2kwmin. 3,8 4,3 5,4 5,6 6,8lfmax. 2,1 2,1 2,1 2,1 3,2r1 min. 0,4 0,4 0,6 0,6 0,6r2fmax. 0,5 0,6 0,7 0,9 1max. 0,36 0,45 0,54 0,63 0,72r3min. 0,16 0,20 0,24 0,28 0,32r4 ref. 5,7 5,7 5,7 5,7 8,8max. 10,00 13,00 16,00 18,00 21,00smin. 9,78 12,73 15,73 17,73 20,67max. 0,25

30、0,30 0,35 0,45 0,50vmin. 0,10 0,15 0,15 0,20 0,25G50G61G67G65 G37G45G4E G31G34G32G31G39 G3A G32G30G30G33Table 1 (continued)Dimensions in millimetresThread size d PaM8 1 M10 10M10 1,25M12 1,25M 12 1,5(M14 1,5)bM16 1,5lg, hlsand lgi, jnom. min. max. lsmin.lgmax.lsmin.lgmax.lsmin.lgmax.lsmin.lgmax.lsmi

31、n.lgmax.16 15,65 16,35 20 19,58 20,42 25 24,58 25,42 30 29,58 30,42 35 34,5 35,5 6,75 13 40 39,5 40,5 11,75 18 6,5 14 45 44,5 45,5 16,75 23 11,5 19 6,25 15 50 49,5 50,5 21,75 28 16,5 24 11,25 20 6 16 55 54,4 55,6 26,75 33 21,5 29 16,25 25 11 21 7 1760 59,4 60,6 31,75 38 26,5 34 21,25 30 16 26 12 226

32、5 64,4 65,6 36,75 43 31,5 39 26,25 35 21 31 17 2770 69,4 70,6 41,75 48 36,5 44 31,25 40 26 36 22 3280 79,4 80,6 51,75 58 46,5 54 41,25 50 36 46 32 4290 89,3 90,7 56,5 64 51,25 60 46 56 42 52100 99,3 100,7 66,5 74 61,25 70 56 66 52 62110 109,3 110,7 71,25 80 66 76 62 72120 119,3 120,7 81,25 90 76 86

33、72 82130 129,2 130,8 80 90 76 86140 139,2 140,8 90 100 86 96150 149,2 150,8 96 106160 159,2 160,8 106 116NOTE If the product passes the gauging in annex A, the requirements for dimensions c, e and kware satisfied.aP is the pitch of the thread.bThe size in parentheses should be avoided if possible.cF

34、or lengths lnom 125 mm.dFor lengths 125 mm 200 mm.fRadius r2applies both at the corners and at the flats of the hexagon.gScrews with lengths shown above the thick stepped line are threaded to the head.hReduced shank type (type R) only below the dashed stepped line.ilgis the minimum grip length.jlg m

35、ax= lnom bls min= lg max 5 P (P is the pitch of the coarse thread with the corresponding diameter, specified in ISO 724).G50G61G67G65 G38G45G4E G31G34G32G31G39 G3A G32G30G30G334 Specifications and relevant European or International StandardsSee table 2.Table 2 Specifications and relevant European an

36、d International StandardsMaterial Steel Stainless steelGeneralrequirementsInternational Standard ISO 8992Tolerance 6gThreadInternational Standards ISO 724, ISO 965-2Property class 8.8, 10.9, 12.9 A2-70MechanicalpropertiesEuropean Standards EN ISO 898-1 EN ISO 3506-1Product grade ATolerancesEuropean

37、Standard EN ISO 4759-1Finishas processedRequirements for electroplating are covered inEN ISO 4042.Requirements for non-electrolytically applied zincflake coatings are covered in EN ISO 10683.PlainSurface discontinuities Limits for surface disconti-nuities are covered inEN 26157-3.Acceptability For a

38、cceptance procedure, see EN ISO 3269.5 DesignationEXAMPLE 1 A hexagon bolt with flange, small series, product grade A, with metric fine pitch thread M12 1,25, nominallength l = 80 mm, type F or U at the option of the manufacturer, and property class 8.8 shall be designated as follows:Hexagon bolt wi

39、th flange EN 14219 M12 1,25 80 8.8EXAMPLE 2 A hexagon bolt with flange, small series, product grade A, with metric fine pitch thread M12 1,25, nominallength l = 80 mm, type F, and property class 8.8 shall be designated as follows:Hexagon bolt with flange EN 14219 M12 1,25 80 F 8.8EXAMPLE 3 If, in sp

40、ecial cases, a hexagon bolt with flange with reduced shank is required, the letter R shall be included inthe designation:Hexagon bolt with flange EN 14219 M12 1,25 80 R 8.8G50G61G67G65 G39G45G4E G31G34G32G31G39 G3A G32G30G30G33Annex A(normative)Gauging of hexagon flange headsA.1 Recommended method f

41、or gauging of hexagon (see figure A.1 and table A.1)The head shall be gauged using two ring gauges, A and B, to demonstrate the coincidental acceptability of hexagonheight, wrenching height, corner fill and width across corners. Gauge A shall be placed over the hexagon and shallseat on the flange. G

42、auge B shall be placed on the top of the head normal to the bolt axis. The two gauges shall notbe in contact.A.2 Recommended method for gauging of flange thickness (see figure A.1 and table A.1)Gauge C is a flat feeler or ring gauge. It is used to prove that the flange thickness at the junction with

43、 the hexagonportion is equal to or greater than specified values. The acceptance criterion is that gauge C shall fit under gauge Awithout contact when the bolt head is seated on a flat plate.Key1 Gauge A2 Gauge B3 Gauge CNOTE Wa, min= etheoreticalWb, max= emin 0,01 mmTa, max= kw, minFigure A.1G50G61

44、G67G65 G31G30G45G4E G31G34G32G31G39 G3A G32G30G30G33Table A.1Dimensions in millimetresGauge A Gauge B Gauge CWa Ta WbTbWcTcNominal threaddiameter(d)max. min. max. min. max. min. min. Max. max. min.8 11,56 11,55 3,80 3,79 10,94 10,93 4 20 1,31 1,3010 15,02 15,01 4,30 4,29 14,25 14,24 4 24 1,81 1,801218,49 18,485,40 5,39 17,61 17,60 5 29 2,20 2,1914 20,79 20,78 5,60 5,59 19,85 19,84 5 32,5 2,55 2,5416 24,26 24,25 6,80 6,79 23,14 23,13 6 37 2,96 2,95BibliographyISO 888:1976, Bolts, screw and studs Nominal lengths, and thread lengths for general purpose bolts.