DIN EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) .pdf

1、September 2017English price group 15No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 23.040.01; 91.140.80!%mtS“27481

2、48www.din.deDIN EN 1453-1Plastics piping systems with structuredwall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PVCU) Part 1: Specifications for pipes and the system;English version EN 14531:2017 + AC:2017,English translation of

3、 DIN EN 1453-1:2017-09KunststoffRohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebuden Weichmacherfreies Polyvinylchlorid (PVCU) Teil 1: Anforderungen an Rohre und das Rohrleitungssystem;Englische Fassung EN 14531:2017

4、 + AC:2017,Englische bersetzung von DIN EN 1453-1:2017-09Systmes de canalisations en plastique avec des tubes paroi structure pour lvacuation deseauxvannes et des eaux uses ( basse et haute temprature) lintrieur des btiments Poly(chlorure de vinyle) non plastifi (PVCU) Partie 1: Spcifications pour t

5、ubes et le systme;Version anglaise EN 14531:2017 + AC:2017,Traduction anglaise de DIN EN 1453-1:2017-09SupersedesDIN EN 14531:200003www.beuth.deDocument comprises 32 pagesDTranslation by DIN-Sprachendienst.In case of doubt, the German-language original shall be considered authoritative.09.17DIN EN 1

6、453-1:2017-09 2 A comma is used as the decimal marker. National foreword This document (EN 1453-1:2017 + AC:2017) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” (Secretariat: NEN, Netherlands). The responsible German body involved in its preparation

7、 was DIN-Normenausschuss Wasserwesen (DIN Standards Committee Water Practice), Joint Working Committee NAW/FNK NA 119-05-41 GA “Systems for soil and waste discharge within the building structure (CEN/TC 155/WG 6)”. This document includes the European Corrigendum EN 1453-1:2017/AC:2017. The start and

8、 finish of text introduced or altered by amendment is indicated in the text by tags null . Amendments This standard differs from DIN EN 1453-1:2000-03 as follows: a) normative references have been rendered more precise; b) the Scope has been limited to “inside buildings”; c) the use of fillers has b

9、een rendered more precise; d) requirements for the density of pipes have been included; e) the uniaxial tensile test has been included; f) an alternative test method for the degree of gelation according to ISO 18373-1 has been included. Previous editions DIN EN 1453-1: 2000-03 EUROPEAN STANDARD NORM

10、E EUROPENNE EUROPISCHE NORM EN 1453-1 January 2017 +AC July 2017 ICS 23.040.01; 23.040.05; 91.140.80 Supersedes EN 1453-1:2000 English Version Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride

11、) (PVC-U) Part 1: Specifications for pipes and the system Systmes de canalisations en plastique avec des tubes paroi structure pour lvacuation des eaux-vannes et des eaux uses ( basse et haute temprature) lintrieur des btiments Poly(chlorure de vinyle) non plastifi (PVC-U) Partie 1: Spcifications po

12、ur tubes et le systme Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebuden Weichmacherfreies Polyvinylchlorid (PVC-U) Teil 1: Anforderungen an Rohre und das Rohrleitungssystem This European Standard was ap

13、proved by CEN on 29 October 2016. The Corrigendum became effective on 5 July 2017 and has been incorporated into this standard. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard

14、 without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any o

15、ther language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republi

16、c, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUR

17、OPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1453-1:2017 + A

18、C:2017 E Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions, symbols and abbreviations . 6 3.1 Terms and definitions . 6 3.2 Symbols . 8 3.3 Abbreviations . 9 4 Material . 9 4.1 Raw material . 9 4.2 Utilization of non-virgin material . 9 4.3 Sealing ring r

19、etaining means 9 5 General characteristics 10 5.1 Appearance . 10 5.2 Colour . 10 6 Geometrical characteristics . 10 6.1 General . 10 6.2 Dimensions of pipes 10 6.3 Dimensions of sockets 13 7 Mechanical characteristics . 19 7.1 General requirements 19 7.2 Additional requirements . 20 8 Physical char

20、acteristics . 21 9 Performance requirements 22 10 Sealing rings . 22 11 Adhesives 22 12 Marking 22 12.1 General . 22 12.2 Minimum required marking 23 12.3 Additional marking . 23 Annex A (informative) Guidance for calcium carbonate additives . 24 A.1 Composition of calcium carbonate additives . 24 A

21、.2 Physical properties of calcium carbonate additive . 24 Annex B (normative) Utilization of non-virgin material . 25 B.1 Own reprocessed material 25 B.2 External reprocessed and recycled materials with agreed specification 25 B.3 External reprocessed and recycled material not covered by an agreed s

22、pecification . 28 Annex C (informative) Product standards . 29 Bibliography . 30 2 DIN EN 1453-1:2017-09 EN 1453-1:2017 + AC:2017 (E) European foreword This document (EN 1453-1:2017) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”, the secretariat of

23、 which is held by NEN. This document supersedes EN 1453-1:2000. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn at the latest by Ju

24、ly 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This standard is a part of a System Standard for plastics piping systems of a particular mat

25、erial for a specified application. There are a number of such System Standards. System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Organization for Stand

26、ardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 1453 consists of the followin

27、g parts, under the general title Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PVC-U) 1): Part 1: Requirements for pipes and the system (the present standard) Part 2: Guidance for the as

28、sessment of conformity (under preparation) This document includes the corrigendum EN 1453-1:2017/AC:2017 which corrects a reference in Clause 2 and Table B.1. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement thi

29、s European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia,

30、 Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. 1) EN 1453 does not cover a recommended practice for installation. A recommended practice for installation is covered by the following European Technical Report: CEN/TR 13801, Plastics piping systems for soil and waste d

31、ischarge (low and high temperature) within the building structure Thermoplastics Recommended practice for installation. 3 DIN EN 1453-1:2017-09 EN 1453-1:2017 + AC:2017 (E) 1 Scope This part of EN 1453 specifies the requirements for structured-wall unplasticized poly(vinyl chloride) (PVC-U) pipes an

32、d the system intended to be used for soil and waste discharge applications (low and high temperature) inside buildings (application area code “B”) NOTE 1 The intended use is reflected in the marking of products by “B”. This part of EN 1453 is also applicable to structured-wall unplasticized poly(vin

33、yl chloride) (PVC-U) pipes, and the system intended for the following purposes: ventilating part of the pipework in association with discharge applications; rainwater pipework inside building. It also specifies the test parameters for the test methods referred to in this standard. NOTE 2 Single laye

34、r foamed PVC-U pipes and spirally-formed PVC-U pipes are not covered by this standard. This standard covers a range of nominal sizes and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taki

35、ng into account their particular requirements and any relevant national regulations and installation practices or codes. For external above ground application additional requirements depending on the climatic conditions should be agreed between the manufacturer and the user. NOTE 4 Pipes conforming

36、to this standard are normally associated with fittings conforming to EN 13291 1. Pipes, fittings and components conforming to any of the product standards listed in Annex C can also be used with pipes conforming to this standard, provided they conform to the requirements for joint dimensions given i

37、n Clause 6 and to the requirements in Table 11. NOTE 5 Joints and adhesives are considered to be part of the system as covered in the scope. NOTE 6 Products conforming to this standard may be submitted to national requirements on fire regulation. 2 Normative references The following documents, in wh

38、ole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals Materials

39、 requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric Seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 1905, Plastics piping systems Unplasticized poly(vi

40、nyl chloride) (PVC-U) pipes, fittings and material Method for assessment of the PVC content based on total chlorine content EN 10204:2004, Metallic products Types of inspection documents EN 14680, Adhesives for non-pressure thermoplastics piping systems Specifications EN 15346:2014, Plastics Recycle

41、d plastics Characterization of poly(vinyl chloride) (PVC) recyclates 4 DIN EN 1453-1:2017-09 EN 1453-1:2017 + AC:2017 (E) EN ISO 306, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) (nullISO 306null) EN ISO 472, Plastics Vocabulary (ISO 472) EN ISO 1043-1, Plastic

42、s Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics (ISO 1043-1) EN ISO 1183-1, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1) EN ISO 2505, Thermoplastics

43、pipes Longitudinal reversion Test method and parameters (ISO 2505) EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions (ISO 3126) EN ISO 3451-5, Plastics Determination of ash Part 5: Poly(vinyl chloride) (ISO 3451-5) EN ISO 6259-1, Thermoplastics pipes Determination

44、of tensile properties Part 1: General test method (ISO 6259-1) EN ISO 13229, Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the viscosity number and K-value (ISO 13229) ISO 2507-1, Thermoplastics pipes and fi

45、ttings Vicat softening temperature Part 1: General test method ISO 3127, Thermoplastics pipes Determination of resistance to external blows Round-the-clock method ISO 6259-2, Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), ch

46、lorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI) ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method ISO 11173:1994, Thermoplastics pipes Determination of resistance to external blows

47、Staircase method ISO 13254, Thermoplastics piping systems for non-pressure applications Test method for watertightness ISO 13255, Thermoplastics piping systems for soil and waste discharge inside buildings Test method for airtightness of joints ISO 13257:2010, Thermoplastics piping systems for non-p

48、ressure applications Test method for resistance to elevated temperature cycling ISO 18373-1, Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature 5 DIN EN 1453-1:2017-09 EN 1453-1:2017 + AC:2017 (E) 3 Terms and definitions, symbols and abbr

49、eviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 472 and EN ISO 1043-1 and the following apply. 3.1.1 application area code code used in the marking of pipes and fittings to indicate the application area(s) for which they are intended, as follows: B: application area code for components intended for use above ground inside the building Note 1 to ent