DIN EN 14934-2007 Thermal insulation and light weight fill products for civil engineering applications - Factory made products of extruded polystyrene foam (XPS) - Specification En.pdf

1、December 2007DEUTSCHE NORM English price group 16No part of this standard may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS 83.100; 93.010!$JX“13

2、99653www.din.deDDIN EN 14934Thermal insulation and light weight fill products for civil engineeringapplications Factory made products of extruded polystyrene foam (XPS) SpecificationEnglish version of DIN EN 14934:2007-12Wrmedmmung und leichte Fllprodukte fr Anwendungen im Tiefbau Werkmig hergestell

3、te Produkte aus extrudiertem Polystyrolschaum (XPS) SpezifikationEnglische Fassung DIN EN 14934:2007-12See start of validitywww.beuth.deDocument comprises 52 pagesDIN EN 14934:2007-12 2 Start of validity This standard is intended to be valid from 1 June 2008. It should be noted that, in Germany, CE

4、conformity marking of construction products conforming to this standard will be permitted once the standard has been listed in the Bundesanzeiger (German Federal Law Gazette). National foreword This standard has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and product

5、s” (Secretariat: DIN, Germany). The responsible German body involved in its preparation was the Normenausschuss Bauwesen (Building and Civil Engineering Standards Committee), Technical Committee NA 005-56-60 AA Wrmedmmstoffe. The European Standards referred to in clause 2 of the EN have been publish

6、ed as the corresponding DIN EN Standards with the same number. For the International Standard ISO 12491 referred to in this standard there is no national standard available. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 14934September 2007ICS 83.100; 93.010English VersionThermal insulation and l

7、ight weight fill products for civilengineering applications - Factory made products of extrudedpolystyrene foam (XPS) - SpecificationProduits isolants thermiques et de remblayage pour lesapplications de gnie civil - Produits manufacturs enmousse de polystyrne extrud (XPS) - SpcificationsWrmedmmung u

8、nd leichte Fllprodukte frAnwendungen im Tiefbau - Werkmig hergestellteProdukte aus extrudiertem Polystyrolschaum (XPS) -SpezifikationThis European Standard was approved by CEN on 13 July 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

9、 giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official v

10、ersions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium

11、, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STAND

12、ARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14934:2007: EEN 14934:2007 (E) Contents Page Foreword4

13、1 Scope 5 2 Normative references 5 3 Terms, definitions, symbols, units and abbreviated terms.6 3.1 Terms and definitions .6 3.2 Symbols, units and abbreviated terms7 4 Requirements.9 4.1 General9 4.2 For all applications 9 4.3 For specific applications.11 5 Test methods17 5.1 Sampling.17 5.2 Condit

14、ioning.17 5.3 Testing 17 6 Designation code.20 7 Evaluation of conformity.21 8 Marking and labelling 22 Annex A (normative) Determination of the declared values of thermal resistance and thermal conductivity23 A.1 Introduction23 A.2 Input data23 A.3 Declared values23 Annex B (normative) Factory Prod

15、uction Control .25 Annex C (normative) Determination of the aged values of thermal resistance and thermal conductivity29 C.1 Scope 29 C.2 Procedure for XPS foam without diffusion tight laminates.29 C.3 Procedure for XPS foam for use with diffusion tight facings on both sides.30 C.4 Calculation of ag

16、ed value .31 C.5 Blowing agent 32 C.6 Product grouping.32 Annex D (normative) Determination of behaviour under cyclic square wave load33 D.1 Scope 33 D.2 Definitions 33 D.3 Principle34 D.4 Testing equipment.34 D.5 Test specimens35 D.6 Procedure .35 D.7 Calculation and expression of results.37 D.8 Ac

17、curacy of measurement38 D.9 Test report 38 Annex E (informative) Additional properties 39 E.1 General39 E.2 Compressive modulus of elasticity .39 E.3 Determination of volume percentage of open and closed cells .39 2EN 14934:2007 (E) E.4 Determination of shear strength39 Annex ZA (informative) Relati

18、onship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive41 ZA.1 Scope and relevant characteristics .41 ZA.2 Procedures for the attestation of conformity of extruded polystyrene foam products.43 ZA.3 CE Marking and labelling48

19、 Bibliography50 Figures Figure D.1 Required load cycle during the fatigue test35 Figure D.2 Dimensions of the test specimen.36 Figure D.3 Test set-up .37 Figure ZA.1 Example CE marking information 49 Tables Table 1 Tolerances of length, width, squareness and flatness10 Table 2 Classes for thickness

20、tolerances 10 Table 3 Levels for compressive stress at 10 % deformation or compressive strength .11 Table 4 Levels for deformation under specified compressive load and temperature conditions.12 Table 5 Levels for compressive stress at 2 % deformation or compressive strength .13 Table 6 Levels for co

21、mpressive stress at 5 % deformation or compressive strength .13 Table 7 Levels for long term water absorption by total immersion 16 Table 8 Levels for long term water absorption by diffusion .16 Table 9 Levels for Freeze-thaw resistance16 Table 10 Test methods, test specimens and conditions18 Table

22、A.1 Values of k for one sided 90 % tolerance interval with a confidence level of 90 % 24 Table B.1 Minimum product testing frequencies25 Table B.2 Minimum product testing frequencies for the reaction to fire characteristics 27 Table E.1 Test methods, test specimens, conditions and minimum testing fr

23、equencies 40 3Table ZA.1 Relevant clauses.42 Table ZA.2 System(s) of attestation of conformity .44 Table ZA.2.1 A ssignment of evaluation of conformity tasks for products under system 1.45 Table ZA.2.2 Assignment of evaluation of conformity tasks for products under system 3 and 3 (with 4 for RtF)46E

24、N 14934:2007 (E) Foreword This document (EN 14934:2007) has been prepared by Technical Committee CEN/TC 88 “Thermal insulating materials and products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identi

25、cal text or by endorsement, at the latest by March 2008, and conflicting national standards shall be withdrawn at the latest by March 2008. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirem

26、ents of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible

27、 for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Ger

28、many, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. 4EN 14934:2007 (E) 1 Scope This European Standard specifies the requirements for factory made p

29、roducts of extruded polystyrene foam which are used for frost insulation of roads, railways, trafficked areas, light weight fill for reduction of horizontal and vertical earth pressure and other civil engineering applications. The products are manufactured in the form of boards, which are also avail

30、able with special edge and surface treatment (tongue the measured values shall be expressed with three significant figures; the thermal resistance, D, shall always be declared. The thermal conductivity, D, shall be declared where possible; the declared thermal resistance, D, and the declared thermal

31、 conductivity, D, shall be given as limit values representing at least 90 % of the production, determined with a confidence level of 90 %; the value of thermal conductivity, 90/90, shall be rounded upwards to the nearest 0,001 W/(mK) and declared as Din levels with steps of 0,001 W/(mK); the declare

32、d thermal resistance, D, shall be calculated from the nominal thickness, dN,and the corresponding thermal conductivity value, 90/90, unless measured directly; the value of thermal resistance, R90/90, when calculated from the nominal thickness, dN, and the corresponding thermal conductivity, 90/90, s

33、hall be rounded downwards to the nearest 0,05 mK/W, and declared as Din levels with steps of 0,05 mK/W; the value of, R90/90, for those products for which only the thermal resistance is measured directly, shall be rounded downwards to the nearest 0,05 mK/W and declared as Din levels with steps of 0,

34、05 mK/W. 4.3.9 Water absorption 4.3.9.1 Long term water absorption by immersion Water absorption by total immersion, Wlt, shall be determined in accordance with EN 12087 method 2A. No test result shall be higher than the value given in Table 7, for the declared level. 15EN 14934:2007 (E) Table 7 Lev

35、els for long term water absorption by total immersion Level Requirement % by volume WL(T) 3 3 WL(T) 1,5 1,5 WL(T) 0,7 0,7 WL(T) 0,5 0,5 4.3.9.2 Long term water absorption by diffusion Water absorption by diffusion, WdV, shall be determined in accordance with EN 12088. No test result shall be higher

36、than the value given in Table 8 for the declared level. Table 8 Levels for long term water absorption by diffusion Level Requirement % by volume WD (V) 5 5 WD (V) 3 3 4.3.10 Freeze-thaw resistance Freeze-thaw resistance shall be determined in accordance with EN 12091 using the test specimen from 4.3

37、.9.2. The additional water absorption, WV, shall be not higher than the value given in Table 9 for the declared level. Table 9 Levels for Freeze-thaw resistance Level Requirement % by volume FTC 5 5 FTC 4 4 FTC 3 3 FTC 2 2 FTC 1 1 After the freeze-thaw test the reduction in compressive stress at 10

38、% deformation, 10, or the compressive strength, m, of the dry specimens, when tested in accordance with EN 826 shall not exceed 10 % of the initial value. 16EN 14934:2007 (E) 4.3.11 Water vapour transmission Water vapour transmission properties shall be determined in accordance with EN 12086, and de

39、clared as the water vapour diffusion resistance factor, , for homogeneous products and as the water vapour resistance, Z, for faced or non-homogeneous products. No test result of, , shall be less than the declared level, MU, chosen from the following levels: 50, 80, 100, 150, 200, 250, 300. If, Z, i

40、s declared, no test result shall be less than the declared value. 4.3.12 Release of dangerous substances NOTE See Annex ZA. 5 Test methods 5.1 Sampling Test specimens shall be taken from the same sample, with a total area of not less than one board, sufficient to cover the needed tests. 5.2 Conditio

41、ning No special conditioning of test specimens is needed unless otherwise specified in this standard. In case of dispute, conditioning of test specimens shall be stored at (23 2) C and (50 5) % relative humidity for at least 6 h prior to testing unless otherwise specified in this standard. 5.3 Testi

42、ng 5.3.1 General Table 10 gives the dimensions of test specimens, the minimum number of measurements required to get one test result and any specific conditions which are necessary. 5.3.2 Thermal resistance and thermal conductivity Thermal resistance and thermal conductivity shall be determined in a

43、ccordance with EN 12667 or EN 12939 for thick products and under the following conditions: at a mean temperature of (10 0,3) C; after conditioning in accordance with 5.2; taking into account the effect of ageing according to Annex C. NOTE Thermal resistance and thermal conductivity may also be measu

44、red at mean temperatures other than 10 C, providing that the accuracy of the relationship between temperature and thermal properties is well documented. Thermal resistance and thermal conductivity shall be determined directly at the measured thickness. In the event that this is not possible, they sh

45、all be determined by measurements on other thicknesses of the product providing that: the product is of similar chemical and physical characteristics and is produced on the same production unit; 17EN 14934:2007 (E) and it can be demonstrated in accordance with EN 12939 that the thermal conductivity

46、does not vary more than 2 % over the range of thicknesses where the calculation is applied. Table 10 Test methods, test specimens and conditions Dimensions in millimetres Clause Test method Specific conditionsNo Title Test specimen length and widthaMinimum number of measurements to get one test resu

47、lt4.2.1 Length and width EN 822 Full size 1 - 4.2.1 Squareness on length and width EN 824 Full size 1 - 4.2.1 Flatness EN 825 Full size 1 - 4.2.2 Thickness EN 823 Full size 1 Load: (250 5) Pa 4.2.3 Dimensional stability under specified temperature and humidity conditions EN 1604 200 x 200 2 Conditio

48、n specimens for 45 days Test condition: 23 C, 90 % relative humidity 4.2.4 Compressive stress at 10% deformation EN 826 100 x 100 5 Condition specimens for 45 days or compressive strength 150 x 150 3 (Length and width of specimen shall be thickness of specimen) 4.2.5.1 Reaction to fire See EN 13501-

49、1 4.2.5.2 Continuous glowing combustion bDimensional stability at specified temperature EN 1604 200 x 200 2 Condition specimens for 45 days 4.3.2 Dimensional stability under specified temperature and humidity conditions EN 1604 200 x 200 2 Condition specimens for 45 days, Test condition: 70 oC, 90 % relative humidity 18EN 14934:2007 (E) Table 10 (continued) Clause Test method Specific conditionsNo Title Test specimen lengt