DIN EN 15202-2012 LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associated equipment connections German version EN 15202 2012《液.pdf

1、September 2012 Translation by DIN-Sprachendienst.English price group 19No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).

2、ICS 23.060.40!$UG“1915036www.din.deDDIN EN 15202LPG equipment and accessories Essential operational dimensions for LPG cylinder valve outlet andassociated equipment connections;English version EN 15202:2012,English translation of DIN EN 15202:2012-09Flssiggas-Gerte und Ausrstungsteile Grundlegende B

3、etriebsmae fr Ausgangsanschlsse von Flaschenventilen frFlssiggas (LPG) und zugehrige Anschlsse fr Gerte;Englische Fassung EN 15202:2012,Englische bersetzung von DIN EN 15202:2012-09quipements pour GPL et leurs accessoires Dimensions oprationnelles essentielles des connexions des robinets et valves d

4、ebouteilles de GPL et des quipements associs;Version anglaise EN 15202:2012,Traduction anglaise de DIN EN 15202:2012-09SupersedesDIN EN 15202:2007-03www.beuth.deIn case of doubt, the German-language original shall be considered authoritative.Document comprises 48 pages 08.12 DIN EN 15202:2012-09 2 A

5、 comma is used as the decimal marker. National foreword This standard has been prepared by CEN/TC 286 “Liquefied Petroleum Gas equipment and accessories” (Secretariat: NSAI, Ireland). The responsible German body involved in its preparation was the Normenausschuss Druckgasanlagen (Pressure Vessels St

6、andards Committee), Working Committee NA 016-00-06 AA Flssiggas-Gerte und Ausrstung; Spiegelausschuss zu CEN/TC 286. The DIN Standards corresponding to the International Standards referred to in this document are as follows: ISO 68-1 DIN ISO 68-1 ISO 3601-1 DIN ISO 3601-1 Amendments This standard di

7、ffers from DIN EN 15202:2007-03 as follows: a) the Introduction has been added; b) the scope has been extended; c) connections type G.65 and type G.66 have been included; d) Annex B (normative) “Unsafe connections” has been added; e) in the German version, the terminology has been revised; f) the st

8、andard has been brought in line with the current rules of presentation. Previous editions DIN EN 15202: 2007-03 National Annex NA (informative) Bibliography DIN ISO 68-1, ISO general purpose metric screw threads Basic profil Part 1: Metric screw threads DIN ISO 3601-1, Fluid power systems O-rings Pa

9、rt 1: Inside diameters, cross-sections, tolerances and designation codes EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15202 May 2012 ICS 23.060.40 Supersedes EN 15202:2006English Version LPG equipment and accessories - Essential operational dimensions for LPG cylinder valve outlet and associ

10、ated equipment connections quipements pour GPL et leurs accessoires - Dimensions oprationnelles essentielles des connexions des robinets et valves de bouteilles de GPL et des quipements associsFlssiggas-Gerte und Ausrstungsteile - Grundlegende Betriebsmae fr Ausgangsanschlsse von Flaschenventilen fr

11、 Flssiggas (LPG) und zugehrige Anschlsse fr Gerte This European Standard was approved by CEN on 13 April 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alte

12、ration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language mad

13、e by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Eston

14、ia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATI

15、ON EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15202:2012: EEN 15202:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normativ

16、e references 53 Terms and definitions .54 Symbols and abbreviations 65 Design .66 Connections in use . 417 Unsafe connections 418 Tightening torque . 419 Marking 41Annex A (informative) Connections by country 42Annex B (normative) Unsafe connections . 45Bibliography . 46DIN EN 15202:2012-09 EN 15202

17、:2012 (E) 3 Foreword This document (EN 15202:2012) has been prepared by Technical Committee CEN/TC 286 “Liquefied Petroleum Gas equipment and accessories”, the secretariat of which is held by NSAI. This European Standard shall be given the status of a national standard, either by publication of an i

18、dentical text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn at the latest by November 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be

19、 held responsible for identifying any or all such patent rights. This document supersedes EN 15202:2006. The revisions to this document include: addition of the Introduction; amendment to the Scope; addition of G65 and G66 connections; amendments to Annex B; and Annex B has been changed to normative

20、. Environmental aspects have been considered in the drafting of this standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic

21、, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. DIN EN 15202:2012-09 EN 15202:2012 (E) 4 Introd

22、uction The primary objective of this European Standard is to ensure the safe connection of LPG cylinder valves to their connectors. This European Standard is the fundamental source for identifying the essential manufacturing dimensions of the LPG cylinder valve connections used in Europe. prEN 16129

23、 is the fundamental source for identifying the essential manufacturing dimensions of other connector types not used with LPG cylinder valves. This European Standard identifies the existing cylinder valves and the connectors that are currently in use with LPG. It is the intention that only connection

24、s which are identified in this standard should be used with LPG cylinder valves. This European Standard lists potentially unsafe connections where it may be possible to connect together, but which, when connected, may not be sound or secure in some operating conditions or orientations. This standard

25、 specifies a marking system that is intended to ensure that only valves and connecters that are marked with the same connector type number are used in combination. DIN EN 15202:2012-09 EN 15202:2012 (E) 5 1 Scope This European Standard specifies basic connection dimensions of LPG cylinder valves (ma

26、nufactured in accordance with EN ISO 14245 and EN ISO 15995) and connectors (including pressure regulators) to enable them to be safely connected together. NOTE 1 Figure 1 (type G.1) to Figure 19 (type G.33) give the types of threaded outlet connections. NOTE 2 Figure 20 (type G.50) to Figure 34 (ty

27、pe G.66) give the types of non-threaded outlet connections. This European Standard lists potentially unsafe connections where it may be possible to connect together, but which, when connected, may not be sound or secure in some operating conditions or orientations. This European Standard specifies a

28、 marking system that is intended to ensure that only valves and connecters that are marked with the same connector type number are used in combination. This European Standard also recommends tightening torques for the attachment of screwed metal-to-metal connections. Quality assurance systems, produ

29、ction testing and particularly certificates of conformity are not covered in this standard. This European Standard excludes connections for automotive vehicles covered by UN/ECE Regulation No. 67 Part 1 and EN 13760. This European Standard excludes connections for gas cartridges covered by EN 417. 2

30、 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendm

31、ents) applies. EN 549, Rubber materials for seals and diaphragms for gas appliances and gas equipment EN 560, Gas welding equipment Hose connections for equipment for welding, cutting and allied processes EN ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dime

32、nsions, tolerances and designation (ISO 228-1) ISO 68-1, ISO general purpose screw threads Basic profile Part 1: Metric screw threads ISO 3601-1, Fluid power systems O-rings Part 1: Inside diameters, cross-sections, tolerances and designation codes ANSI/CGA V-1, American National, Compressed Gas Ass

33、ociation Standard for Compressed Gas Cylinder Valve Outlet and Inlet Connections ANSI/ASME/B1.5, ACME Screw Threads issued by American Society of Mechanical Engineers 1990 DIN 477-1, Gas cylinder valves rated for test pressures up to 300 bar; types, sizes, and outlets 3 Terms and definitions For the

34、 purposes of this document, the following terms and definitions apply. DIN EN 15202:2012-09 EN 15202:2012 (E) 6 3.1 liquefied petroleum gas LPG low pressure gas composed of one or more light hydrocarbons which are assigned to UN 1011, UN 1075, UN 1965, UN 1969 or UN 1978 only and which consists main

35、ly of propane, propene, butane, butane isomers, butene with traces of other hydrocarbon gases 3.2 connector device that attaches to a cylinder valve to allow the passage of LPG to or from the cylinder 3.3 valve operating mechanism mechanism that opens the valve when, or after, a regulator or connect

36、or is fitted and closes the valve automatically when, or before, a regulator or connector is disconnected 4 Symbols and abbreviations NBR Nitrile Butadiene Rubber (Acrylonitrile-butadiene rubber) (see ISO 4658). STP Standard Temperature and Pressure 15,6 C (288,7 K), 1,013 bar absolute (0,1013 MPa a

37、bsolute) IRHD International Rubber Hardness Degrees LH Left hand RH Right hand INT Internal thread EXT External thread ref make reference to 5 Design The dimensions shall be in accordance with those given in the following figures. The travel distance of the valve operating mechanisms is identified w

38、here required. The drawings show the location of sealing elements where required. Any hexagon nut with a left hand (LH) thread shall, for easy identification, have notches (for example a 60V groove) midway at the corners of each adjoining spanner flat. Where concentricity and surface finish are not

39、specified, the requirements shall be as specified by the manufacturer. New valve/connection proposals shall not make an unsafe connection or interference fit with the valves and connectors shown in this European Standard. DIN EN 15202:2012-09 EN 15202:2012 (E) 7 Dimensions in millimetres Key Connect

40、or/Nut Seal Thread 1 nut A1 14,80 - 15 B1 16,8 - 17 T1 20 min 2 connector A2 10,5 - 10,6 B2 10,2 - 10,4 T2 18,838 19,973 3 seal A3 17,4 - 17,5 B3 2,0 2,2 T3 17,696 18,266 4 valve A4 4,8 5,2 Seal material shall be NBR or equivalent, or EN 549 A2/H3 T4 1,814 5 nut thread A5 2,9 3,1 T5 55 6 valve threa

41、d A6 14 min Valve T6 R 0,249 A7 20 x 1,814 LH C1 20 x 1,814 LH T7 19,589 19,98 A8 15,15 - 15,26 C2 14,3 14,7 T8 18,703 18,838 A9 2,9 3,1 C3 11,1 11,3 T9 17,317 17,676 A10 11 min C4 6,8 - 7,2 A11 15,8 16,2 C5 R0,3 R0,7 A12 25 A/F C6 6,0 6,313 8,4 max C7 7,0 10,0 C8 11 minC9 0,5 x 90Figure 1 Type G.1

42、Threaded connection 20 x 1,814 LH - Spanner tightenedDIN EN 15202:2012-09 EN 15202:2012 (E) 8 Dimensions in millimetres Key Nut Connector Black Seal1 nut A1 21,8 x 1,814 LH B1 18,5 18,7 C1 17,7 - 18,0 2 connector A2 16 max B2 12,2 12,3 C2 10,7 - 11,0 3 black seal A3 24,6 min B3 11,1 11,3 C3 1,7 2,0

43、4 seal A4 7,5 min B4 0,9 1,0 Material shall be: a) NBR or equivalent; or 5 valve A5 7,5 8,1 B5 2,0 2,2 b) EN 549 A2/H3 6 nut thread A6 9,9 10,5 B6 2,4 2,6 Thread 7 valve thread A7 12,5 min B7 9,0 max T1 21,8 min A8 5 wings equally spaced B8 A2 0,10,3T2 20,622 20,722 Valve Seal T3 19,444 19,544 D1 21

44、,7 x 1,814 LH E1 13,35 - 13,65 T4 1,814 D2 13 13,1 E2 8,0 - 8,4 T5 60 D3 7,8 8,0 E3 7,5 7,8 T6 R 0,249 D4 8,6 8,7 Material shall be: a) NBR or equivalent; or b) EN 549 A2/H3 T7 21,6 21,7 T8 20,422 20,522 T9 18,7 18,8 Figure 2 Type G.2 Threaded connection 21,7 x 1,814 LH - 60 Hand tightened DIN EN 15

45、202:2012-09 EN 15202:2012 (E) 9 Dimensions in millimetres Key Connector Seal 1 connector A1 27 - 27,21 B1 25,7 - 26,3 2 seal A2 13,9 - 14,1 B2 14,0 - 14,6 3 gasket A3 3,0 - 3,2 B3 1,35 1,65 4 valve A4 6,4 - 6,6 Material shall be: a) NBR or equivalent; or b) EN 549 A2/H3 5 example of one configuratio

46、n of the inlet/gas passage to the connector A5 13,7 - 13,9 A6 M16 x 1,5-6g A7 1,6 1,8 Valve A8 1,4 1,6 D1 M16 x 1,5 6H A9 3,9 4,1 D2 8,4 8,6 10 1,2 1,4 D3 26,5 27,3 A11 13,4 13,6 D4 1 x 45 Gasket D5 10,3 10,5 C1 7,5 0,15 D6 10,2 10,6 C2 17,0 0,1 D7 1,0 min C3 1,5 0,15 C4 4,0 0,15 Figure 3 Type G.3 T

47、hreaded connection M16 x 1,5 RH - Hand tightened DIN EN 15202:2012-09 EN 15202:2012 (E) 10 Dimensions in millimetres Key Connector/Nut Seal 1 nut A1 18,8 - 19,2 B1 19,8 - 19,2 2 connector A2 Ra 3,2 B2 11,6 - 12 3 seal A3 11,3 - 11,7 B3 1,9 2,1 4 valve A4 10,8 - 11,2 Material shall be: a) NBR or equivalent; or b) EN 549 A2/H3 A5 11,89 - 12,0 A6 1,7 1,9 A7 4,9 5,1 Valve A8 5,9 6,1 C1 W 21,8 x 1,814 LH DIN 477-1 A9 8 max C2 12,7 13,3 A10 30 A/F C3 6,8